Don't operate under the assumption that every device that uses the em2820
default USB ID is a Prolink PlayTV USB.  We have an eeprom hash, so use that,
since otherwise we cannot support other devices with the 2820 default USB ID
(such as the ADS Tech Instant TV USB USBAV-704)
Signed-off-by: NDevin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add the em2870 to the list of known em28xx chip ids.
Signed-off-by: NDevin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Changes/fixes on em28xx dev->lock:

- em28xx_init_dev() were unlocking without a previous lock;

- some read ioctls need to lock after the removal of KBL, since a write
  may be happening at the same time an ioctl is reading;

- keep the device locked during all device initialization;

- lock/unlock while reading/writing registers.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

vidioc_try_fmt_vid_cap() just checks if a given resolution is supported.
It doesn't touch on struct em28xx device descriptor. so, there's no need
to lock.

While there, use unlikely() for those values that aren't likely to
occur.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Added specific entry for WinTV-HVR 850
Signed-off-by: NDouglas Schilling Landgraf <dougsland@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

em28xx devices generally get hot when xc3028 tuner is powered on. This
patch solves this by turning power off when the device is not used, at the
expense of having a higher load time, when calling a TV application.

Since firmware load happens on 1 or 2 seconds on most devices, this is not a pain.

Also, it helps to save the planet by saving some power :)
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Change log format to look more like URB transactions. In fact, setup and
IN/OUT transactions are merged. This helps to debug the driver.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Print manufacturer/product info from USB device and also card entry.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Prints usb speed used by em28xx interface. While there, fixes USB ID's
endiannes.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Several chips may be turned off when the device is not used, like audio,
video and dvb demods. This patch adds a gpio callback at the core
structs to allow turning off such devices.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

A previous changeset moved gpio from em28xx struct into em28xx_board.
However, the driver were not updated to properly honor those gpio's.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Before this patch, several devices without tuner were kept the value 0
for tuner_type. However, this means TUNER_TEMIC_PAL. Replace those
entries for the proper TUNER_ABSENT value.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Instead of using magic vmux/amux, let's use an alias where possible.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Instead of a large, ugly switch specifying the gpio tables for each
device, let's move it into the boards struct. This also helps to see
what boards have already the gpio's for DVB.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Replaces all occurrences of em28xx_write_regs_req() and em28xx_write_reg()
used to setup register names by em28xx_write_reg().

Also, documents the register names that are known.

This patch were generated by this small perl script:

my %reg_map = (
	# Register table - the same as defined on parse_em28xx.pl script
);

while (<>) {
	if (m/(.*)em28xx_write_regs_req\(dev\,\s*0x00\,\s*(.*)\,\s*\"\\x(..)\",\s*1\)\;(.*)/) {
		my $reg = $2;
		my $val = $3;
		$val =~ tr/A-f/a-f/;
		$reg = $reg_map{$reg} if defined($reg_map{$reg});
		printf "$1em28xx_write_reg(dev, %s, 0x%s);$4\n", $reg, $val;
	} elsif (m/(.*)em28xx_write_regs\(dev\,\s*(.*)\,\s*\"\\x(..)\",\s*1\)\;(.*)/) {
		my $reg = $2;
		my $val = $3;
		$val =~ tr/A-f/a-f/;
		$reg = $reg_map{$reg} if defined($reg_map{$reg});
		printf "$1em28xx_write_reg(dev, %s, 0x%s);$4\n", $reg, $val;
	} else {
		print $_;
	}
}
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Now, the first message states board names. Also, removed printing the alternate
settings by default. I2C messages are now clearer.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Since saa7115 has saa711x chip auto-detection, there's no need on differenciating
it at cards table. Just use the generic name for all boards that use a philips
saa711x decoder.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Several fields are duplicated on both structs. Let's just copy em28xx_board instead.

A later cleanup could just copy the fields that are changed, in order to keep em28xx_board
const.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Remove unused em28xx_board.vchannels and em28xx.video_channels.
Also, .is_em2800 = 0 is not needed, as all data is zeroed by kernel loader.

The table also included a notice that svideo weren't test on Hauppauge
USB2. Remove this notice, since this input also works properly.

Also, it does some whitespace cleanups.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The previous patches removed XCLK and I2C magic. Now, we finally know
what those registers do. Also, only a very few cards need different
setups for those.

Instead of keeping the setups for those values inside the per-device
hack magic switch, move the uncommon values to the board-specific
struct, and have a common setup for all other boards.

So, almost 100 lines of hacking magic were removed.

A co-lateral effect of this patch is that it also fixes a bug at em28xx-core, where xclk
were set, without taking any care about not overriding a previous xclk setup.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Cleanup the calls to set the GPIOs and GPOs for various devices,
replacing the register number with the #define from em28xx-reg.h and
converting over to using em28xx_write_reg()
Signed-off-by: NDevin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Convert over to setting the XCLK register usage with the new em28xx_write_reg()
function.

Thanks to Ray Lu from Empia for providing the em2860/2880 datasheet.
Signed-off-by: NDevin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

On some em28xx devices, there's an unused interface. This is printed on
the logs as an error. We can just ignore that interface.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

If removing and reiserting the driver on some devices, tuner type will
be unset at the second time. This patch fixes this issue.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch cleans up the entries of xc2028/3028, since those devices
don't need or use a tda9887.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Pixelview uses a Sigmatel stac codec. It has an external line out pin,
connected to AC97_MASTER_VOL. It also provides I2S output, but using a
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Some devices use more than one AC97 outputs. This patch allows such
devices to properly work.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Some boards use different AC97 setups for output. This patch adds the
capability of specifying the output to be used. Currently, only one
output is selected, but the better is to allow user to select it via a
mixer, on alsa driver.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Convert the calls that write the i2c clock register over to the new
em28xx_write_reg() function that allows for or'ing bits
Signed-off-by: NDevin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Introduce a new function that writes to a single register.  This is
useful because the vast majority of register writes are a single
register, and this format permits or'ing register value bits together.
Signed-off-by: NDevin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

AC97 devices provide several input and outputs. However, before this
patch, em28xx device weren't properly allowing the usage of ac97
possible combinations. Also, several input volumes were left untouched,
instead of making sure that the volumes were set on mute state.

This patch improves support for ac97 devices by allowing to use any
inputs, and making sure that unused inputs are set on mute state.

Yet, some work is still needed to select the AC97 output.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This makes easier to identify vendor ID, since AC97 vendors are
generally identified by 3 bytes. The remaining byte is used by the
vendor to identify its devices.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>