Use the macros provided by mac80211 and remove redundant
declarations inside the drivers.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On lower WLAN signal strength, WLAN downlink traffic might suffer
from retransmissions. At the mean time, playing SCO/A2DP profiles
is affecting WLAN stability. In such scenario, by stomping SCO/A2DP
BT traffic completely for a BTCOEX period, gives WLAN traffic an
oppertunity to recover PHY rate. It also improves WLAN stability at
lower RSSI without sacificing BT traffic.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch reverts the commit "ath9k_hw: Wait BT calibration to complete"
and bail out from MCI interrupt routine for chip reset. The above commit
stalls the WLAN TCP traffic while bringing up and down the BT interface
iteratively. Fixing this properly by queueing up chip reset and bailing
out properly from tasklet routine.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

FATAL and WATCHDOG interrupts should be processed first followed
by others.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The debugfs file for dumping btcoex parameters unconditionally
assumes a MCI-based device. This will not work for older btcoex
chips. Fix this by branching out the routine into separate
functions.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit "ath9k: improve suspend/resume reliability" broke ath9k_htc
and bringing up the device would hang indefinitely. Fix this.

Cc: stable@vger.kernel.org
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

2484 Mhz (Japan) usage requires filter coefficients to
be programmed in the CCK TX FIR registers. This is required
for AR9331, AR9485 and AR9462. Fix this and also remove
a few useless macros and a duplicate variable.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

'|' has higher precedence than ?:.  Since AR5K_PHY_TURBO_MODE is 0x1 and
"AR5K_PHY_TURBO_MODE | (ah->ah_radio == AR5K_RF2425)" is true then we
always set turbo to zero.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Simplify the code by make use of module_platform_driver macro.
Signed-off-by: NSyam Sidhardhan <s.syam@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The workaround for ASPM/L0s is needed only for AR9485 1.0,
which was never sold and is not supported by ath9k.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

An issue is reported in AR9462 & AR9565 that NF_cal_not_done is
not observed when HW peak detector calibration is disabled. At that
state, the HW is stuck at NF calibration which prevents tx output.
The root cause is wrong peak detector offset calibrated by HW. To
resolve this issue, peak detector calibration is done manually by SW
for AR9462 and AR9565.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add 5% width tolerance for radar patterns defined by ETSI.
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As ath6kl firmware can't do intersections the driver should only listen
to regdom changes from cellular base stations, all other requests need to
be refused.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

A missing else caused a potential NULL dereference.
Reported-by: NYuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: NPontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

__be32 variables where used a little careless leading to sparse warnings.
Treat them a little more gentle.
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NPontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Just use WARN_ON rather than an if containing only WARN_ON(1).

A simplified version of the semantic patch that makes this transformation
is as follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression e;
@@
- if (e) WARN_ON(1);
+ WARN_ON(e);
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the module_usb_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.

dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is pretty pointless. Lets kill this to stop people from
thinking that its actually used. Maybe we should go on
a crusade and kill this completely from the kernel.

Cc: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Acked-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Free instance of pattern detector if requested DFS domain is
not supported.
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

set_domain() is already defined in /arch/arm/asm/domain.h
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

During hardware restart, all interfaces are iterated even
though they haven't been re-added to the driver, document
this behaviour. The same also happens during resume, which
is even more confusing since all of the interfaces were
previously removed from the driver. Make this optional so
drivers relying on the current behaviour can still use it,
but to let drivers that don't want this behaviour disable
it.

Also convert all API users, keeping the old semantics
except in hwsim, where the new normal ones are desired.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

A negative buffer size doesn't make sense and it breaks this check in
ar5523_get_max_rxsz():

	if (!ar->rxbufsz || ar->rxbufsz > AR5523_SANE_RXBUFSZ) { ...
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ath9k xmit functions for AMPDUs can send frames as non-aggregate in case
only one frame is currently available. The client will then answer using a
normal Ack instead of a BlockAck. This acknowledgement has no TID stored and
therefore the hardware is not able to provide us the corresponding TID.

The TID set by the hardware in the tx status descriptor has to be seen as
undefined and not as a valid TID value for normal acknowledgements. Doing
otherwise results in a massive amount of retransmissions and stalls of
connections.

Users may experience low bandwidth and complete connection stalls in
environments with transfers using multiple TIDs.

This regression was introduced in b11b160d
("ath9k: validate the TID in the tx status information").
Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Cc: stable@vger.kernel.org
Acked-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The TX power setting is currently per wiphy (hardware
device) but with multi-channel capabilities that doesn't
make much sense any more.

Allow drivers (and mac80211) to advertise support for
per-interface TX power configuration. When the TX power
is configured for the wiphy, the wdev will be NULL and
the driver can still handle that, but when a wdev is
given the TX power can be set only for that wdev now.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Whenever WLAN receives scheduling msg from BT, it reduces tx power
based on RSSI level. And then BT starts simultaneous transmission
along with WLAN. Sometimes HW MAC compares tx power that is used
prior to power reduction which is causing BT transmission to defer.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reduced the power consumption to half in full and network sleep.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reduced the power consumption to half in full and network sleep.

Cc: stable@vger.kernel.org
Cc: Paul Stewart <pstew@chromium.org>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This driver is for the AR5523 chipset from Atheros. It was created
in 2007 by Christoph Hellwig but it was never finished. I found it a
couple of months ago and after some polishing it's working pretty
fine.

The driver was written with the FreeBSD driver (uath) as reference,
which was written with the reverse-engineered windows driver as
reference, hence the feature set is very limited. Station mode
only, no HW crypto offload.
Signed-off-by: NPontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

carl9170_handle_mpdu is the final part of the
rx path of the driver. It splits the raw data
streams from the device into skb packets and
passes them on to mac80211. As a result of
continuous updates, it grew over the years when
new code was added by the following commits:
	- report A-MPDU status
	- fix HT peer BA session corruption
	- A-MPDU frame type filter
	- ...

This patch splits the routine into two stages.
The first stage only deals with the details
about extracting and verifying the data from
the incoming stream. Whereas the second stage
packs it into skbs and passes it on to mac80211.
Reported-by: NJavier Lopez <jlopex@cozybit.com>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the BT connection is initiated by headset, it's possible that headset
requests to make one A2DP and one Voice connection over the same link.
BT firmware will send a new profile A2DP_Voice in this case. So WLAN
has to take care of this new profile for tuning BTCOEX parameters.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Whenever i_coff of IQ calibration is too high, AR9565 drops max
rx rate to MCS4. Skipping IQ update at this time can avoid this
problem for AR9565.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

While resuming from S3, BT host issues HCI reset command and it
causes BT firmware to busy with security key calculation. At this
movement, WLAN detects MCI hardware error of MCI_CONT_INFO_TIMEOUT
and then it starts the recovery sequence repeatedly. Too many
recovery sequences would exhaust the BT kernel message pool. This
patch imposes a duration between consecutive BT recovery procedure.
Thus it solves BT firmware panic issue reported in AR9565.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

TXIQ and RXIQ share the same data path to upload the measurement
result, we should turn off RXIQ calibration while re-calibrating radio
Signed-off-by: NBala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>