MegaRAID older Firmware does not support uneven span configuration for PRL11.
E.g User wants to create 34 Driver PRL11 config, it was not possible using old
firmware, since it was not supported configuration in old firmware

Old Firmware expect even number of Drives in each span and same number of
physical drives at each span.  Considering above design, 17 Drives at Span-0
and 17 drives at span-1 was not possible.

Now, using this new feature Firmware and Driver both required changes.  New
Firmware can allow user to create 16 Drives at span-0 and 18 Drives at
span-1. This will allow user to create 34 Drives Uneven span PRL11.

RAID map is interface between Driver and FW to fetch all required
fields(attributes) for each Virtual Drives.  Since legacy RAID map consider
Even Span design, there was no place to keep Uneven span information in
existing Raid map.  Because of this limitation, for Uneven span VD, driver can
not use RAID map.

This patch address the changes required in Driver to support Uneven span PRL11
support.

1. Driver will find if Firmware has UnevenSpanSupport or not by reading
   Controller Info.
2. If Firmware has UnvenSpan PRL11 support, then Driver will inform about its
   capability of handling UnevenSpan PRL11 to the firmware.
3. Driver will update its copy of span info on each time Raid map update is
   called.
4. Follow different IO path if it is Uneven Span. (For Uneven Span, Driver
   uses Span Set info to find relavent fields for that particular Virtual
   Disk)

More verbose prints will be available by setting "SPAN_DEBUG" to 1 at
compilation time.
Signed-off-by: NSumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This Driver will use more than 8 MSI-x support provided by Invader/Fury max
upto 128 MSI-x.

[jejb: fix checkpatch warning]
Signed-off-by: NSumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NSumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NSumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NSumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NSumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Free event detail memory from more common place, instead of doing it for
limited device types.
Signed-off-by: NSumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: NAdam Radford <aradford@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NSumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NSumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Do not return SCSI_MLQUEUE_HOST_BUSY, but send DID_ERROR to SCSI mid-layer, if
adapter is in critical error state.  "SCSI_MLQUEUE_HOST_BUSY" will keep same
SCSI command in loop and it is not a right return value, if controller is
hardware critical error.
Signed-off-by: NSumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Make the driver return appropriate sense data when an unsupported
operation is queued. This will cause the SCSI layer to stop issuing the
offending command.
Reported-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Acked-by: NAdam Radford <aradford@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Not all disks fill out the VPD pages correctly. Add a blacklist flag
that allows us ignore the SBC-3 VPD pages for a given device. The
BLIST_SKIP_VPD_PAGES flag triggers our existing skip_vpd_pages
scsi_device parameter to bypass VPD scanning.

Also blacklist the offending Seagate drive model.
Reported-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

If CONFIG_SCSI_MPT2SAS_LOGGING is undefined, then these warnings are emitted

drivers/scsi/mpt2sas/mpt2sas_scsih.c: In function '_scsih_sas_broadcast_primitive_event'
drivers/scsi/mpt2sas/mpt2sas_scsih.c:5810:40: warning: unused variable 'event_data'

Use pr_info() function instead of dewtprintk().
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

[jejb: checkpatch fixes]
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

When SCSI command is received with task attribute not set, set it to SIMPLE.
Previously it is set to untagged. This causes the firmware to fail the commands.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@lsi.com>
Cc: stable@vger.kernel.org
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Modified device scan routine so each configuration page read breaks from the
while loop when the ioc_status is not equal to MPI2_IOCSTATUS_SUCCESS.

[jejb: checkpatch fixes]
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@lsi.com>
Cc: stable@vger.kernel.org
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Updated the mpt2sas driver code that issues hard reset to comply with the
timing requirements mentioned in MPI specifications rev V.

[jejb: checpatch fixes]
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Change set in MPI 2.0 Rev W(2.00.15) specification and 2.00.27 header files

1. Added a bit to the IOCExceptions field of the IOCFacts Reply to indicate
   that the IOC detected a partial memory failure.
2. Added ElapsedSeconds field to RAID Volume Indicator Structure. Added
   Elapsed Seconds Valid flag to Flags field of this structure.
3. Added ElapsedSeconds field to Integrated RAID Operations Status Event Data.
4. In the IOCSettings field of BIOS Page 1, modified the Adapter Support bits
   description to specify X86 BIOS.
5. Toolbox Diagnostic CLI Tool Request may now use chain elements in the SGL.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Missing delay is not getting set properly. The reason is that it is not
defined in the same file from where it is being invoked.  The fix is to move
the missing delay module parameter from mpt2sas_base.c to mpt2sas_scsh.c.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@lsi.com>
Cc: stable@vger.kernel.org
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

- Retain firmware defined configuration settings in the absence of
user-provided configuration by eliminating the global RSS and the
PF/VF capabilities mailbox commands.
- Remove S_IRUGO from sysfs parameters that don't have 'show'
functionality.
Signed-off-by: NNaresh Kumar Inna <naresh@chelsio.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Resending the patch as it didn't make the linux-scsi list.

This patch fixes fcs rport state machine to address ocassional Brocade
FC Direct Attach LUN discovery failure due to not sending PLOGI accept
to the target.
Signed-off-by: NVijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

When a switch disable/enable or a reboot is done, the HBA port gets an
offline and a subsequent online notification. When the port comes up a
link up notification is sent to bfa from the firmware. The bfa then send
an FLOGI to the firmware which is sent out on the wire.
The switch port meanwhile goes offline (presumably for diagnostics)
which causes the switch not to respond to the FLOGI.
The link down notification is sent to the HBA driver. However owing to a
bug in the lps state machine handling the lps state machine does not
move to sm_init state (it remains in sm_login state and send a login
complete message to fcs). This results in a zero PID assignment as the
login is not really complete.

This fix is to correctly handle the events in lps state machine.
Signed-off-by: NVijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Introduce eh_timeout which can be used for error handling purposes. This
was previously hardcoded to 10 seconds in the SCSI error handling
code. However, for some fast-fail scenarios it is necessary to be able
to tune this as it can take several iterations (bus device, target, bus,
controller) before we give up.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

When multipathed systems run into an all-paths-down scenario
all devices might be dropped, too. This causes 'del_gendisk'
to be called, which will unregister the kobj_map->probe()
function for all disk device numbers.
When the device comes back the default ->probe() function
is run which will call __request_module(), which will
deadlock.
As 'del_gendisk' typically does _not_ trigger a module unload
the default ->probe() function is pointless anyway.
This patch implements a dummy ->probe() function, which will
just return NULL if the disk is not registered.
This will avoid the deadlock. Plus it'll speed up device
scanning.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Defined target_ids,array_ids and vsets_ids as unsigned long to avoid
target_destroy accessing memory after it was freed.
Signed-off-by: NWen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

If NO_DMA=y:

drivers/built-in.o: In function `ufshcd_transfer_req_compl':
drivers/scsi/ufs/ufshcd.c:1182: undefined reference to `scsi_dma_unmap'
drivers/built-in.o: In function `ufshcd_map_sg':
drivers/scsi/ufs/ufshcd.c:377: undefined reference to `scsi_dma_map'
drivers/built-in.o: In function `ufshcd_do_reset':
drivers/scsi/ufs/ufshcd.c:912: undefined reference to `scsi_dma_unmap'
drivers/built-in.o: In function `ufshcd_memory_alloc':
drivers/scsi/ufs/ufshcd.c:565: undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `ufshcd_free_hba_memory':
drivers/scsi/ufs/ufshcd.c:185: undefined reference to `dma_free_coherent'
drivers/scsi/ufs/ufshcd.c:192: undefined reference to `dma_free_coherent'
drivers/scsi/ufs/ufshcd.c:199: undefined reference to `dma_free_coherent'
drivers/scsi/ufs/ufshcd.c:185: undefined reference to `dma_free_coherent'
drivers/scsi/ufs/ufshcd.c:192: undefined reference to `dma_free_coherent'
drivers/built-in.o:drivers/scsi/ufs/ufshcd.c:199: more undefined references to `dma_free_coherent' follow
drivers/built-in.o: In function `ufshcd_abort':
drivers/scsi/ufs/ufshcd.c:1498: undefined reference to `scsi_dma_unmap'
drivers/built-in.o: In function `ufshcd_device_reset':
drivers/scsi/ufs/ufshcd.c:1436: undefined reference to `scsi_dma_unmap'
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NSantosh Y <santoshsy@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Commit 0998d063 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NSantosh Y <santoshsy@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Coccinelle complains about the inconsistent NULL checking on "t".  It
turns out the check isn't needed because we verified that "t" is
non-NULL at the start of the function.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NAnand Kumar Santhanam <AnandKumar.Santhanam@pmcs.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Remove the arbitrary expectation in libsas that all SCSI commands are 16 bytes
or less.  Instead do all copies via cmd->cmd_len (and use a pointer to this in
the libsas task instead of a copy).  Note that this still doesn't enable > 16
byte CDB support in the underlying drivers because their internal format has
to be fixed and the wire format of > 16 byte CDBs according to the SAS spec is
different.  the libsas drivers (isci, aic94xx, mvsas and pm8xxx are all
updated for this change.

Cc: Lukasz Dorau <lukasz.dorau@intel.com>
Cc: Maciej Patelczyk <maciej.patelczyk@intel.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Jack Wang <xjtuwjp@gmail.com>
Cc: Lindar Liu <lindar_liu@usish.com>
Cc: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This fixes a bug where the iscsi class/driver did not do a put_device
when a sess/conn device was found. This also simplifies the interface
by not having to pass in some arguments that were duplicated and did
not need to be exported.
Reported-by: NZhao Hongjiang <zhaohongjiang@huawei.com>
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Acked-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

These enums have been separate since the dawn of SAS, mainly because the
latter is a procotol only enum and the former includes additional state
for libsas.  The dichotomy causes endless confusion about which one you
should use where and leads to pointless warnings like this:

drivers/scsi/mvsas/mv_sas.c: In function 'mvs_update_phyinfo':
drivers/scsi/mvsas/mv_sas.c:1162:34: warning: comparison between 'enum sas_device_type' and 'enum sas_dev_type' [-Wenum-compare]

Fix by eliminating one of them.  The one kept is effectively the sas.h
one, but call it sas_device_type and make sure the enums are all
properly namespaced with the SAS_ prefix.
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Modified thermal configuration to happen after interrupt registration
Added SAS controller configuration during initialization
Added error handling logic to handle I_T_Nexus errors and variants

[jejb: fix up tabs and spaces issues]
Signed-off-by: NAnand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: NJack Wang <jack_wang@usish.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Handled NCQ errors in the low level driver as the FW
is not providing the faulty tag for NCQ errors for libsas
to recover.

[jejb: fix checkpatch issues]
Signed-off-by: NAnand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: NJack Wang <jack_wang@usish.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Individual WWN read operations based on controller.
PM8081 - Read WWN from Flash VPD.
PM8088/89 - Read WWN from EEPROM.
PM8001 - Read WWN from NVM.
Signed-off-by: NSakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: NAnand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: NJack Wang <jack_wang@usish.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Changed name in driver to pm80xx. Updated debug messages.
Signed-off-by: NSakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: NAnand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: NJack Wang <jack_wang@usish.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Performing pci_free_consistent in tasklet had result in a core dump. So
allocated a new memory region for it. Fix for passing proper address
and operation in firmware flash update.
Signed-off-by: NSakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: NAnand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: NJack Wang <jack_wang@usish.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Additional bar shift for new SPC firmware, applicable to device
id 0x8081 only.
Signed-off-by: NSakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: NAnand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: NJack Wang <jack_wang@usish.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Implementation of SPCv/ve specific hardware functionality and
macros. Changing common functionalities wrt SPCv/ve operations.
Conditional checks for SPC specific operations.
Signed-off-by: NSakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: NAnand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: NJack Wang <jack_wang@usish.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>