Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 23 9月, 2009 4 次提交
  3. 20 6月, 2009 2 次提交
  5. 11 6月, 2009 1 次提交
  7. 21 5月, 2009 1 次提交
  9. 07 5月, 2009 1 次提交
  11. 27 1月, 2009 1 次提交
  13. 07 1月, 2009 1 次提交
    • D
      spi_gpio driver · d29389de
      由 David Brownell 提交于 
      Generalize the old at91rm9200 "bootstrap" bitbanging SPI master driver as
"spi_gpio", so it works with arbitrary GPIOs and can be configured through
platform_data.  Such SPI masters support:

 - any number of bus instances (bus_num is the platform_device.id)
 - any number of chipselects (one GPIO per spi_device)
 - all four SPI_MODE values, and SPI_CS_HIGH
 - i/o word sizes from 1 to 32 bits;
 - devices configured as with any other spi_master controller

When configured using platform_data, this provides relatively low clock
rates.  On platforms that support inlined GPIO calls, significantly
improved transfer speeds are also possible with a semi-custom driver.
(It's still painful when accessing flash memory, but less so.)

Sanity checked by using this version to replace both native controllers on
a board with six different SPI slaves, relying on three different
SPI_MODE_* values and both SPI_CS_HIGH settings for correct operation.

[akpm@linux-foundation.org: cleanups]
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NMagnus Damm <damm@igel.co.jp>
Tested-by: NMagnus Damm <damm@igel.co.jp>
Cc: Torgil Svensson <torgil.svensson@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      d29389de
  15. 06 8月, 2008 1 次提交
  17. 25 7月, 2008 1 次提交
  19. 13 5月, 2008 1 次提交
  21. 28 4月, 2008 1 次提交
  23. 07 2月, 2008 2 次提交
  25. 26 1月, 2008 1 次提交
    • E
      [ARM] pxa: make pxa2xx_spi driver use ssp_request()/ssp_free() · 2f1a74e5
      由 eric miao 提交于 
      1. make pxa2xx_spi.c use ssp_request() and ssp_free() to get the common
   information of the designated SSP port.

2. remove those IRQ/memory request code, ssp_request() has done that for
   the driver

3. the SPI platform device is thus made psuedo, no resource (memory/IRQ)
   has to be defined, all will be retreived by ssp_request()

4. introduce ssp_get_clk_div() to handle controller difference in clock
   divisor setting

5. use clk_xxx() API for clock enable/disable, and clk_get_rate() to
   handle the different SSP clock frequency between different processors
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
      2f1a74e5
  27. 23 11月, 2007 1 次提交
  29. 17 10月, 2007 1 次提交
  31. 18 7月, 2007 6 次提交
  33. 11 5月, 2007 1 次提交
  35. 10 5月, 2007 1 次提交
  37. 09 5月, 2007 2 次提交
    • J
      au1550 SPI controller driver · 63bd2359
      由 Jan Nikitenko 提交于 
      Here is a driver for the Alchemy au1550 PSC (Programmable Serial
Controller) in SPI master mode.

It supports dma transfers using the Alchemy descriptor based dma controller
for 4-8 bits per word SPI transfers.  For 9-24 bits per word transfers, pio
irq based mode is used to avoid setup of dma channels from scratch on each
number of bits per word change.

Tested with au1550; this may also work on other MIPS Alchemy cpus, like
au1200/au1210/au1250.  Used extensively with SD card connected via SPI;
this handles 8.1MHz SPI clock transfers using dma without any problem (the
highest SPI clock freq possible with au1550 running on 324MHz).

The driver supports sharing of SPI bus by multiple devices.  All features
of Alchemy SPI mode are supported (all SPI modes, msb/lsb first, bits per
word in 4-24 range).

As the SPI clock of the controller depends on main input clock that shall
be configured externally, platform data structure for au1550 SPI controller
driver contains mainclk_hz attribute to define the input clock rate.  From
this value, dividers of the controller for SPI clock are set up for
required frequency.
Signed-off-by: NJan Nikitenko <jan.nikitenko@gmail.com>

Whitespace and section fixups.  Remove partial workaround for platform
setup bug in dma_mask setup; it couldn't work with multiple controllers.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      63bd2359
    • A
      /dev/spidevB.C interface · 814a8d50
      由 Andrea Paterniani 提交于 
      Add a filesystem API for <linux/spi/spi.h> stack.  The initial version of
this interface is purely synchronous.

dbrownell@users.sourceforge.net:

 Cleaned up, bugfixed; much simplified; added preliminary documentation.

 Works with mdev given CONFIG_SYSFS_DEPRECATED; and presumably udev.

 Updated SPI_IOC_MESSAGE ioctl to full spi_message semantics, supporting
 groups of one or more transfers (each of which may be full duplex if
 desired).

 This is marked as EXPERIMENTAL with an explicit disclaimer that the API
 (notably the ioctls) is subject to change.
Signed-off-by: NAndrea Paterniani <a.paterniani@swapp-eng.it>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      814a8d50
  39. 08 5月, 2007 1 次提交
  41. 15 2月, 2007 1 次提交
  43. 13 2月, 2007 4 次提交
  45. 30 11月, 2006 1 次提交
  47. 22 5月, 2006 3 次提交