Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/wireless/orinoco/orinoco.c

This patch adds two new device ids to the asix driver.

One comes directly from the asix driver on their web site, the other was
reported by Armani Liao as needed for the MSI X320 to get the driver to
work properly for it.
Reported-by: NArmani Liao <aliao@novell.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently there are two paths for filling rx buffer queues. One is
used during initialization and the other during runtime.  This patch
removes ql_alloc_sbq_buffers() and ql_alloc_lbq_buffers() and replaces
them with a call to the runtime functions ql_update_lbq() and
ql_update_sbq().
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RX Buffers are refilled in chunks of 16 at a time before notifying the
hardware with a register write.  This can cause several writes to take
place in a given napi poll call.  This change causes the write to take place
only once at the end of the call.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of taking/giving the hw semaphore repeatedly when iterating over
several frame to queue route settings, we have the caller hold it until
all are done.
This reduces PCI bus chatter and possible waits.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of taking/giving the semaphore repeatedly when iterating over
several adderesses, we have the caller hold it until all are done.  This
reduces PCI bus chatter and possible waits.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Setting MAC addresses and routing frames to various queues will need to
be done in response to firmware events as well as during initialization.
This change encapsulates the facilities into a single call that can
later me made from other places.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The functions time_before is more robust for comparing
jiffies against other values.
Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The functions time_before is more robust for comparing
jiffies against other values.
Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The functions time_before is more robust for comparing
jiffies against other values.
Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove some pointless conditionals before kfree_skb().

The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
expression E;
@@
- if (E)
- 	kfree_skb(E);
+ kfree_skb(E);
// </smpl>
Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes the return value of nlmsg_notify() as follows:

If NETLINK_BROADCAST_ERROR is set by any of the listeners and
an error in the delivery happened, return the broadcast error;
else if there are no listeners apart from the socket that
requested a change with the echo flag, return the result of the
unicast notification. Thus, with this patch, the unicast
notification is handled in the same way of a broadcast listener
that has set the NETLINK_BROADCAST_ERROR socket flag.

This patch is useful in case that the caller of nlmsg_notify()
wants to know the result of the delivery of a netlink notification
(including the broadcast delivery) and take any action in case
that the delivery failed. For example, ctnetlink can drop packets
if the event delivery failed to provide reliable logging and
state-synchronization at the cost of dropping packets.

This patch also modifies the rtnetlink code to ignore the return
value of rtnl_notify() in all callers. The function rtnl_notify()
(before this patch) returned the error of the unicast notification
which makes rtnl_set_sk_err() reports errors to all listeners. This
is not of any help since the origin of the change (the socket that
requested the echoing) notices the ENOBUFS error if the notification
fails and should resync itself.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Acked-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A receive coalescing timeout of 250 usec appears to strike a good
balance between allowing enough received frames to be aggregated for
LRO to do its job and not allowing the connection to stall due to
delaying ACKs to the remote end for too long.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the netif_carrier_off() call in ->open() to port probe, so that
ethtool doesn't report the link as being up before we have up'd the
interface.

Move initialisation of the rx/tx coalescing timers from ->open() to
port probe, so that we don't reset the coalescing timers every time
the interface is up'd.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Split pci probe function into smaller logical blocks.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add ethtool wake on lan support.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

it was pointed out on the list that ixgbe was failing when using 64kB pages
and large 16kB MTU.

since with a 64kB PAGE_SIZE MAX_SKB_FRAGS = 3, the way the driver was
configuring page usage was assuming 2kB is half a page, and was only
ever dmaing that much data to a half page.

(16kB - header size) / 2048 = 7 or 8 pages, which would far exceed 3

adjust the driver to account for these large pages, the hardware can
support DMA to up to 16kB for each descriptor.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

From: Shannon Nelson <shannon.nelson@intel.com>

The ring_feature member of ixgbe_adapter is statically allocated based on
the supported features of the device.  When a new feature is added, we need
to manually update the static allocation.  This patch makes the feature
list an enum, eliminating the need for multiple updates to the code when
adding a new feature.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix regression introduded by commit 079aa88f (netfilter: xt_recent: IPv6 support):

From http://bugzilla.kernel.org/show_bug.cgi?id=12753:

Problem Description:
An uninitialized buffer causes IPv4 addresses added manually (via the +IP
command to the proc interface) to never match any packets. Similarly, the -IP
command fails to remove IPv4 addresses.

Details:
In the function recent_entry_lookup, the xt_recent module does comparisons of
the entire nf_inet_addr union value, both for IPv4 and IPv6 addresses. For
addresses initialized from actual packets the remaining 12 bytes not occupied
by the IPv4 are zeroed so this works correctly. However when setting the
nf_inet_addr addr variable in the recent_mt_proc_write function, only the IPv4
bytes are initialized and the remaining 12 bytes contain garbage.

Hence addresses added in this way never match any packets, unless these
uninitialized 12 bytes happened to be zero by coincidence. Similarly, addresses
cannot consistently be removed using the proc interface due to mismatch of the
garbage bytes (although it will sometimes work to remove an address that was
added manually).

Reading the /proc/net/xt_recent/ entries hides this problem because this only
uses the first 4 bytes when displaying IPv4 addresses.

Steps to reproduce:
$ iptables -I INPUT -m recent --rcheck -j LOG
$ echo +169.254.156.239 > /proc/net/xt_recent/DEFAULT
$ cat /proc/net/xt_recent/DEFAULT
src=169.254.156.239 ttl: 0 last_seen: 119910 oldest_pkt: 1 119910

[At this point no packets from 169.254.156.239 are being logged.]

$ iptables -I INPUT -s 169.254.156.239 -m recent --set
$ cat /proc/net/xt_recent/DEFAULT
src=169.254.156.239 ttl: 0 last_seen: 119910 oldest_pkt: 1 119910
src=169.254.156.239 ttl: 255 last_seen: 126184 oldest_pkt: 4 125434, 125684, 125934, 126184

[At this point, adding the address via an iptables rule, packets are being
logged correctly.]

$ echo -169.254.156.239 > /proc/net/xt_recent/DEFAULT
$ cat /proc/net/xt_recent/DEFAULT
src=169.254.156.239 ttl: 0 last_seen: 119910 oldest_pkt: 1 119910
src=169.254.156.239 ttl: 255 last_seen: 126992 oldest_pkt: 10 125434, 125684, 125934, 126184, 126434, 126684, 126934, 126991, 126991, 126992
$ echo -169.254.156.239 > /proc/net/xt_recent/DEFAULT
$ cat /proc/net/xt_recent/DEFAULT
src=169.254.156.239 ttl: 0 last_seen: 119910 oldest_pkt: 1 119910
src=169.254.156.239 ttl: 255 last_seen: 126992 oldest_pkt: 10 125434, 125684, 125934, 126184, 126434, 126684, 126934, 126991, 126991, 126992

[Removing the address via /proc interface failed evidently.]

Possible solutions:
- initialize the addr variable in recent_mt_proc_write
- compare only 4 bytes for IPv4 addresses in recent_entry_lookup
Signed-off-by: NPatrick McHardy <kaber@trash.net>