The MODULE_FIRMWARE() for 3160 should be using the 7260 version as
it's done in the device configuration struct instead of referencing
IWL3160_UCODE_API_OK which doesn't even exist.

Cc: <stable@vger.kernel.org> [3.8+]
Reported-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The csa_countdown flag was not cleared when the AP is stopped.
As a result, if the AP was stopped after csa_countdown had started,
all the folowing channel switch commands would fail.
Fix that by clearing the csa_countdown flag when the AP is stopped.

Cc: <stable@vger.kernel.org> [3.17+]
Signed-off-by: NAvraham Stern <avraham.stern@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The code to send the RX PN data (for each TID) to the firmware
has a devastating bug: it overwrites the data for TID 0 with
all the TID data, leaving the remaining TIDs zeroed. This will
allow replays to actually be accepted by the firmware, which
could allow waking up the system.

Cc: <stable@vger.kernel.org> [3.1+]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The code to send the RX PN data (for each TID) to the firmware
has a devastating bug: it overwrites the data for TID 0 with
all the TID data, leaving the remaining TIDs zeroed. This will
allow replays to actually be accepted by the firmware, which
could allow waking up the system.

Cc: <stable@vger.kernel.org> [3.1+]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When going into/coming out of D3, the TX PN must be programmed into
and restored from the firmware respectively. The restore was broken
due to my previous commit to move PN assignment into the driver.
Sending the PN to the firmware still worked since we now use the
counter that's shared with mac80211, but accessing it through the
mac80211 API makes no sense now.

Fix this by reading/writing the counter directly. This actually
simplifies the code since we don't need to round-trip through the
key_seq structure.

Fixes: ca8c0f4b ("iwlwifi: mvm: move TX PN assignment for CCMP to the driver")
Cc: <stable@vger.kernel.org> [4.1+]
Reported-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Pull networking updates from David Miller:
 "Another merge window, another set of networking changes.  I've heard
  rumblings that the lightweight tunnels infrastructure has been voted
  networking change of the year.  But what do I know?

   1) Add conntrack support to openvswitch, from Joe Stringer.

   2) Initial support for VRF (Virtual Routing and Forwarding), which
      allows the segmentation of routing paths without using multiple
      devices.  There are some semantic kinks to work out still, but
      this is a reasonably strong foundation.  From David Ahern.

   3) Remove spinlock fro act_bpf fast path, from Alexei Starovoitov.

   4) Ignore route nexthops with a link down state in ipv6, just like
      ipv4.  From Andy Gospodarek.

   5) Remove spinlock from fast path of act_gact and act_mirred, from
      Eric Dumazet.

   6) Document the DSA layer, from Florian Fainelli.

   7) Add netconsole support to bcmgenet, systemport, and DSA.  Also
      from Florian Fainelli.

   8) Add Mellanox Switch Driver and core infrastructure, from Jiri
      Pirko.

   9) Add support for "light weight tunnels", which allow for
      encapsulation and decapsulation without bearing the overhead of a
      full blown netdevice.  From Thomas Graf, Jiri Benc, and a cast of
      others.

  10) Add Identifier Locator Addressing support for ipv6, from Tom
      Herbert.

  11) Support fragmented SKBs in iwlwifi, from Johannes Berg.

  12) Allow perf PMUs to be accessed from eBPF programs, from Kaixu Xia.

  13) Add BQL support to 3c59x driver, from Loganaden Velvindron.

  14) Stop using a zero TX queue length to mean that a device shouldn't
      have a qdisc attached, use an explicit flag instead.  From Phil
      Sutter.

  15) Use generic geneve netdevice infrastructure in openvswitch, from
      Pravin B Shelar.

  16) Add infrastructure to avoid re-forwarding a packet in software
      that was already forwarded by a hardware switch.  From Scott
      Feldman.

  17) Allow AF_PACKET fanout function to be implemented in a bpf
      program, from Willem de Bruijn"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1458 commits)
  netfilter: nf_conntrack: make nf_ct_zone_dflt built-in
  netfilter: nf_dup{4, 6}: fix build error when nf_conntrack disabled
  net: fec: clear receive interrupts before processing a packet
  ipv6: fix exthdrs offload registration in out_rt path
  xen-netback: add support for multicast control
  bgmac: Update fixed_phy_register()
  sock, diag: fix panic in sock_diag_put_filterinfo
  flow_dissector: Use 'const' where possible.
  flow_dissector: Fix function argument ordering dependency
  ixgbe: Resolve "initialized field overwritten" warnings
  ixgbe: Remove bimodal SR-IOV disabling
  ixgbe: Add support for reporting 2.5G link speed
  ixgbe: fix bounds checking in ixgbe_setup_tc for 82598
  ixgbe: support for ethtool set_rxfh
  ixgbe: Avoid needless PHY access on copper phys
  ixgbe: cleanup to use cached mask value
  ixgbe: Remove second instance of lan_id variable
  ixgbe: use kzalloc for allocating one thing
  flow: Move __get_hash_from_flowi{4,6} into flow_dissector.c
  ixgbe: Remove unused PCI bus types
  ...

Pull device mapper update from Mike Snitzer:

 - a couple small cleanups in dm-cache, dm-verity, persistent-data's
   dm-btree, and DM core.

 - a 4.1-stable fix for dm-cache that fixes the leaking of deferred bio
   prison cells

 - a 4.2-stable fix that adds feature reporting for the dm-stats
   features added in 4.2

 - improve DM-snapshot to not invalidate the on-disk snapshot if
   snapshot device write overflow occurs; but a write overflow triggered
   through the origin device will still invalidate the snapshot.

 - optimize DM-thinp's async discard submission a bit now that late bio
   splitting has been included in block core.

 - switch DM-cache's SMQ policy lock from using a mutex to a spinlock;
   improves performance on very low latency devices (eg. NVMe SSD).

 - document DM RAID 4/5/6's discard support

[ I did not pull the slab changes, which weren't appropriate for this
  tree, and weren't obviously the right thing to do anyway.  At the very
  least they need some discussion and explanation before getting merged.

  Because not pulling the actual tagged commit but doing a partial pull
  instead, this merge commit thus also obviously is missing the git
  signature from the original tag ]

* tag 'dm-4.3-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm cache: fix use after freeing migrations
  dm cache: small cleanups related to deferred prison cell cleanup
  dm cache: fix leaking of deferred bio prison cells
  dm raid: document RAID 4/5/6 discard support
  dm stats: report precise_timestamps and histogram in @stats_list output
  dm thin: optimize async discard submission
  dm snapshot: don't invalidate on-disk image on snapshot write overflow
  dm: remove unlikely() before IS_ERR()
  dm: do not override error code returned from dm_get_device()
  dm: test return value for DM_MAPIO_SUBMITTED
  dm verity: remove unused mempool
  dm cache: move wake_waker() from free_migrations() to where it is needed
  dm btree remove: remove unused function get_nr_entries()
  dm btree: remove unused "dm_block_t root" parameter in btree_split_sibling()
  dm cache policy smq: change the mutex to a spinlock

Fengguang reported, that some randconfig generated the following linker
issue with nf_ct_zone_dflt object involved:

  [...]
  CC      init/version.o
  LD      init/built-in.o
  net/built-in.o: In function `ipv4_conntrack_defrag':
  nf_defrag_ipv4.c:(.text+0x93e95): undefined reference to `nf_ct_zone_dflt'
  net/built-in.o: In function `ipv6_defrag':
  nf_defrag_ipv6_hooks.c:(.text+0xe3ffe): undefined reference to `nf_ct_zone_dflt'
  make: *** [vmlinux] Error 1

Given that configurations exist where we have a built-in part, which is
accessing nf_ct_zone_dflt such as the two handlers nf_ct_defrag_user()
and nf_ct6_defrag_user(), and a part that configures nf_conntrack as a
module, we must move nf_ct_zone_dflt into a fixed, guaranteed built-in
area when netfilter is configured in general.

Therefore, split the more generic parts into a common header under
include/linux/netfilter/ and move nf_ct_zone_dflt into the built-in
section that already holds parts related to CONFIG_NF_CONNTRACK in the
netfilter core. This fixes the issue on my side.

Fixes: 308ac914 ("netfilter: nf_conntrack: push zone object into functions")
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While testing various Kconfig options on another issue, I found that
the following one triggers as well on allmodconfig and nf_conntrack
disabled:

  net/ipv4/netfilter/nf_dup_ipv4.c: In function ‘nf_dup_ipv4’:
  net/ipv4/netfilter/nf_dup_ipv4.c:72:20: error: ‘nf_skb_duplicated’ undeclared (first use in this function)
    if (this_cpu_read(nf_skb_duplicated))
  [...]
  net/ipv6/netfilter/nf_dup_ipv6.c: In function ‘nf_dup_ipv6’:
  net/ipv6/netfilter/nf_dup_ipv6.c:66:20: error: ‘nf_skb_duplicated’ undeclared (first use in this function)
    if (this_cpu_read(nf_skb_duplicated))

Fix it by including directly the header where it is defined.

Fixes: bbde9fc1 ("netfilter: factor out packet duplication for IPv4/IPv6")
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch just to re-submit the patch "db3421c1" because the
patch "4d494cdc" remove the change.

Clear any pending receive interrupt before we process a pending packet.
This helps to avoid any spurious interrupts being raised after we have
fully cleaned the receive ring, while still allowing an interrupt to be
raised if we receive another packet.

The position of this is critical: we must do this prior to reading the
next packet status to avoid potentially dropping an interrupt when a
packet is still pending.
Acked-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We previously register IPPROTO_ROUTING offload under inet6_add_offload(),
but in error path, we try to unregister it with inet_del_offload(). This
doesn't seem correct, it should actually be inet6_del_offload(), also
ipv6_exthdrs_offload_exit() from that commit seems rather incorrect (it
also uses rthdr_offload twice), but it got removed entirely later on.

Fixes: 3336288a ("ipv6: Switch to using new offload infrastructure.")
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull SG updates from Jens Axboe:
 "This contains a set of scatter-gather related changes/fixes for 4.3:

   - Add support for limited chaining of sg tables even for
     architectures that do not set ARCH_HAS_SG_CHAIN.  From Christoph.

   - Add sg chain support to target_rd.  From Christoph.

   - Fixup open coded sg->page_link in crypto/omap-sham.  From
     Christoph.

   - Fixup open coded crypto ->page_link manipulation.  From Dan.

   - Also from Dan, automated fixup of manual sg_unmark_end()
     manipulations.

   - Also from Dan, automated fixup of open coded sg_phys()
     implementations.

   - From Robert Jarzmik, addition of an sg table splitting helper that
     drivers can use"

* 'for-4.3/sg' of git://git.kernel.dk/linux-block:
  lib: scatterlist: add sg splitting function
  scatterlist: use sg_phys()
  crypto/omap-sham: remove an open coded access to ->page_link
  scatterlist: remove open coded sg_unmark_end instances
  crypto: replace scatterwalk_sg_chain with sg_chain
  target/rd: always chain S/G list
  scatterlist: allow limited chaining without ARCH_HAS_SG_CHAIN

Pull block driver updates from Jens Axboe:
 "On top of the 4.3 core block IO changes, here are the driver related
  changes for 4.3.  Basically just NVMe and nbd this time around:

   - NVMe:
      - PRACT PI improvement from Alok Pandey.
      - Cleanups and improvements on submission queue doorbell and
        writing, using CMB if available.  From Jon Derrick.
      - From Keith, support for setting queue maximum segments, and
        reset support.
      - Also from Jon, fixup of u64 division issue on 32-bit archs and
        wiring up of the reset support through and ioctl.
      - Two small cleanups from Matias and Sunad

  - Various code cleanups and fixes from Markus Pargmann"

* 'for-4.3/drivers' of git://git.kernel.dk/linux-block:
  NVMe: Using PRACT bit to generate and verify PI by controller
  NVMe:Remove unreachable code in nvme_abort_req
  NVMe: Add nvme subsystem reset IOCTL
  NVMe: Add nvme subsystem reset support
  NVMe: removed unused nn var from nvme_dev_add
  NVMe: Set queue max segments
  nbd: flags is a u32 variable
  nbd: Rename functions for clearness of recv/send path
  nbd: Change 'disconnect' to be boolean
  nbd: Add debugfs entries
  nbd: Remove variable 'pid'
  nbd: Move clear queue debug message
  nbd: Remove 'harderror' and propagate error properly
  nbd: restructure sock_shutdown
  nbd: sock_shutdown, remove conditional lock
  nbd: Fix timeout detection
  nvme: Fixes u64 division which breaks i386 builds
  NVMe: Use CMB for the IO SQes if available
  NVMe: Unify SQ entry writing and doorbell ringing

Pull core block updates from Jens Axboe:
 "This first core part of the block IO changes contains:

   - Cleanup of the bio IO error signaling from Christoph.  We used to
     rely on the uptodate bit and passing around of an error, now we
     store the error in the bio itself.

   - Improvement of the above from myself, by shrinking the bio size
     down again to fit in two cachelines on x86-64.

   - Revert of the max_hw_sectors cap removal from a revision again,
     from Jeff Moyer.  This caused performance regressions in various
     tests.  Reinstate the limit, bump it to a more reasonable size
     instead.

   - Make /sys/block/<dev>/queue/discard_max_bytes writeable, by me.
     Most devices have huge trim limits, which can cause nasty latencies
     when deleting files.  Enable the admin to configure the size down.
     We will look into having a more sane default instead of UINT_MAX
     sectors.

   - Improvement of the SGP gaps logic from Keith Busch.

   - Enable the block core to handle arbitrarily sized bios, which
     enables a nice simplification of bio_add_page() (which is an IO hot
     path).  From Kent.

   - Improvements to the partition io stats accounting, making it
     faster.  From Ming Lei.

   - Also from Ming Lei, a basic fixup for overflow of the sysfs pending
     file in blk-mq, as well as a fix for a blk-mq timeout race
     condition.

   - Ming Lin has been carrying Kents above mentioned patches forward
     for a while, and testing them.  Ming also did a few fixes around
     that.

   - Sasha Levin found and fixed a use-after-free problem introduced by
     the bio->bi_error changes from Christoph.

   - Small blk cgroup cleanup from Viresh Kumar"

* 'for-4.3/core' of git://git.kernel.dk/linux-block: (26 commits)
  blk: Fix bio_io_vec index when checking bvec gaps
  block: Replace SG_GAPS with new queue limits mask
  block: bump BLK_DEF_MAX_SECTORS to 2560
  Revert "block: remove artifical max_hw_sectors cap"
  blk-mq: fix race between timeout and freeing request
  blk-mq: fix buffer overflow when reading sysfs file of 'pending'
  Documentation: update notes in biovecs about arbitrarily sized bios
  block: remove bio_get_nr_vecs()
  fs: use helper bio_add_page() instead of open coding on bi_io_vec
  block: kill merge_bvec_fn() completely
  md/raid5: get rid of bio_fits_rdev()
  md/raid5: split bio for chunk_aligned_read
  block: remove split code in blkdev_issue_{discard,write_same}
  btrfs: remove bio splitting and merge_bvec_fn() calls
  bcache: remove driver private bio splitting code
  block: simplify bio_add_page()
  block: make generic_make_request handle arbitrarily sized bios
  blk-cgroup: Drop unlikely before IS_ERR(_OR_NULL)
  block: don't access bio->bi_error after bio_put()
  block: shrink struct bio down to 2 cache lines again
  ...

Pull first round of SCSI updates from James Bottomley:
 "This includes one new driver: cxlflash plus the usual grab bag of
  updates for the major drivers: qla2xxx, ipr, storvsc, pm80xx, hptiop,
  plus a few assorted fixes.

  There's another tranch coming, but I want to incubate it another few
  days in the checkers, plus it includes a mpt2sas separated lifetime
  fix, which Avago won't get done testing until Friday"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (85 commits)
  aic94xx: set an error code on failure
  storvsc: Set the error code correctly in failure conditions
  storvsc: Allow write_same when host is windows 10
  storvsc: use storage protocol version to determine storage capabilities
  storvsc: use correct defaults for values determined by protocol negotiation
  storvsc: Untangle the storage protocol negotiation from the vmbus protocol negotiation.
  storvsc: Use a single value to track protocol versions
  storvsc: Rather than look for sets of specific protocol versions, make decisions based on ranges.
  cxlflash: Remove unused variable from queuecommand
  cxlflash: shift wrapping bug in afu_link_reset()
  cxlflash: off by one bug in cxlflash_show_port_status()
  cxlflash: Virtual LUN support
  cxlflash: Superpipe support
  cxlflash: Base error recovery support
  qla2xxx: Update driver version to 8.07.00.26-k
  qla2xxx: Add pci device id 0x2261.
  qla2xxx: Fix missing device login retries.
  qla2xxx: do not clear slot in outstanding cmd array
  qla2xxx: Remove decrement of sp reference count in abort handler.
  qla2xxx: Add support to show MPI and PEP FW version for ISP27xx.
  ...

Pull MTD updates from Brian Norris:
 "SPI NOR:
   - reduce virtual address space requirements for fsl-quadspi memory map
   - new fsl-quadspi IP support: imx6ul-qspi and imx7d-qspi
   - add new NOR flash device support
   - add new driver for NXP SPI Flash Interface (SPIFI)
   - stop abusing SPI API structs for non-SPI framework
   - fixup DT table matching for new "jedec,spi-nor" string

  NAND:
   - brcmnand: fix big endian MIPS macro usage
   - denali: refactor to use devres, dev_*() printing, etc.
   - OMAP ELM: change the module alias to actually be usable
   - pxa3xx_nand: fixup a few command sequencing issues -- both new and old
      - race conditions in the IRQ handler status clearing
      - problems when a bootloader left interrupts pending
      - config issues when overriding the bootloader configuration
   - new flash device support
   - sunxi_nand:
      - optimize timing configuration by calculation, rather than fixed
        fail-safe values
      - use EDO setting from ONFI
   - r852: fix compiler warnings
   - davinci: add 4KB page support

  Core:
   - oobtest: correct debug print information"

* tag 'for-linus-20150901' of git://git.infradead.org/linux-mtd: (42 commits)
  mtd: mtd_oobtest: Fix the address offset with vary_offset case
  mtd: blkdevs: fix switch-bool compilation warning
  mtd: spi-nor: stop (ab)using struct spi_device_id
  mtd: nand: add Toshiba TC58NVG0S3E to nand_ids table
  mtd: dataflash: Export OF module alias information
  nand: pxa3xx: Increase READ_ID buffer and make the size static
  mtd: nand: pxa3xx-nand: fix random command timeouts
  mtd: nand: pxa3xx_nand: fix early spurious interrupt
  mtd: pxa3xx_nand: add a default chunk size
  mtd: omap_elm: Fix module alias
  mtd: physmap_of: fix null pointer deference when kzalloc returns null
  mtd: nettel: do not ignore mtd_device_register() failure in nettel_init()
  mtd: denali_pci: switch to dev_err()
  mtd: denali_pci: refactor driver using devres API
  mtd: denali_pci: use module_pci_driver() macro
  mtd: denali: hide core part from user in Kconfig
  mtd: spi-nor: add Spansion S25FL204K support
  mtd: spi-nor: Improve Kconfig help text for SPI_FSL_QUADSPI
  mtd: spi-nor: add driver for NXP SPI Flash Interface (SPIFI)
  doc: dt: add documentation for nxp,lpc1773-spifi
  ...

Xen's PV network protocol includes messages to add/remove ethernet
multicast addresses to/from a filter list in the backend. This allows
the frontend to request the backend only forward multicast packets
which are of interest thus preventing unnecessary noise on the shared
ring.

The canonical netif header in git://xenbits.xen.org/xen.git specifies
the message format (two more XEN_NETIF_EXTRA_TYPEs) so the minimal
necessary changes have been pulled into include/xen/interface/io/netif.h.

To prevent the frontend from extending the multicast filter list
arbitrarily a limit (XEN_NETBK_MCAST_MAX) has been set to 64 entries.
This limit is not specified by the protocol and so may change in future.
If the limit is reached then the next XEN_NETIF_EXTRA_TYPE_MCAST_ADD
sent by the frontend will be failed with NETIF_RSP_ERROR.
Signed-off-by: NPaul Durrant <paul.durrant@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Acked-by: NWei Liu <wei.liu2@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit a5597008 ("phy: fixed_phy: Add gpio to determine link up/down.")
added a new argument to fixed_phy_register(), but missed to update bgmac
driver, causing the following build failure:

drivers/net/ethernet/broadcom/bgmac.c:1450:2: error: too few arguments to function 'fixed_phy_register'

Add the missing argument.
Reported-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

diag socket's sock_diag_put_filterinfo() dumps classic BPF programs
upon request to user space (ss -0 -b). However, native eBPF programs
attached to sockets (SO_ATTACH_BPF) cannot be dumped with this method:

Their orig_prog is always NULL. However, sock_diag_put_filterinfo()
unconditionally tries to access its filter length resp. wants to copy
the filter insns from there. Internal cBPF to eBPF transformations
attached to sockets don't have this issue, as orig_prog state is kept.

It's currently only used by packet sockets. If we would want to add
native eBPF support in the future, this needs to be done through
a different attribute than PACKET_DIAG_FILTER to not confuse possible
user space disassemblers that work on diag data.

Fixes: 89aa0758 ("net: sock: allow eBPF programs to be attached to sockets")
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: NAlexei Starovoitov <ast@plumgrid.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull cgroup updates from Tejun Heo:

 - a new PIDs controller is added.  It turns out that PIDs are actually
   an independent resource from kmem due to the limited PID space.

 - more core preparations for the v2 interface.  Once cpu side interface
   is settled, it should be ready for lifting the devel mask.
   for-4.3-unified-base was temporarily branched so that other trees
   (block) can pull cgroup core changes that blkcg changes depend on.

 - a non-critical idr_preload usage bug fix.

* 'for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup: pids: fix invalid get/put usage
  cgroup: introduce cgroup_subsys->legacy_name
  cgroup: don't print subsystems for the default hierarchy
  cgroup: make cftype->private a unsigned long
  cgroup: export cgrp_dfl_root
  cgroup: define controller file conventions
  cgroup: fix idr_preload usage
  cgroup: add documentation for the PIDs controller
  cgroup: implement the PIDs subsystem
  cgroup: allow a cgroup subsystem to reject a fork

Pull percpu updates from Tejun Heo:
 "Minor cleanups"

* 'for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
  percpu: clean up of schunk->map[] assignment in pcpu_setup_first_chunk
  percpu: update incorrect comment for this_cpu_*() operations

Pull workqueue updates from Tejun Heo:
 "Only three trivial changes for workqueue this time - doc, MAINTAINERS
  and EXPORT_SYMBOL updates"

* 'for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
  workqueue: fix some docbook warnings
  workqueue: Make flush_workqueue() available again to non GPL modules
  workqueue: add myself as a dedicated reviwer

Pull libata updates from Tejun Heo:
 "Nothing interesting.  A couple device specific minor updates and a
  kernel doc change"

* 'for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  ata: pata_arasam_cf: Use devm_clk_get
  libata: fix libata-core.c kernel-doc warning
  ata: sata_rcar: Remove obsolete sata-r8a779* platform_device_id entries

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit c6cc1ca7 ("flowi: Abstract out functions to get flow hash
based on flowi") introduced a bug in __skb_set_sw_hash where we
require a dependency on evaluating arguments in a function in order.
There is no such ordering enforced in C, so this incorrect. This
patch fixes that by splitting out the arguments. This bug was
found via a compiler warning that keys may be uninitialized.
Signed-off-by: NTom Herbert <tom@herbertland.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2015-09-01

This series contains updates to i40e, ixgbe and ixgbevf.

Anjali fixes a bug in i40e where the port is not receiving multicast or VLAN
tagged packets in promiscuous mode.  Which can occur when a software bridge
is created on top of the device.

Don adds support in ixgbe that indicates the presence of management firmware.
Added support for entering low power link up state on devices that support
it when the device is closing or suspending.  Updated the driver to report
unknown bus speed and width since IOSF does not report a PCIe bus speed or
width for X550 devices.  Also added the new bus type for integrated I/O
interface (IOSF).  Cleaned up of redundant code in ixgbe.

Mark adds support for UDP-encapsulation transmit checksum and for VXLAN
receive offloads.  Introduces a helper function to do the register access
and processing to avoid needless PHY access on copper PHYs.  Added support
for reporting 2.5G link speed.  Fixed warnings resulting from redundant
initializations of the get_bus_info field.

Maninder Singh updates the ixgbe driver to use kzalloc instead of kcalloc
for allocation of one thing.

Tom Barbette adds support for ethtool to change the rxfh indirection table
and/or key using ethtool interface.

Emil resolves an issue where users were not able to dynamically set number
of queues for 82598 via ethtool -L.

Alex Williamson removes bimodal SR-IOV disabling behavior since it is
confusing to users and results in a state where the PF is broken for other
uses unless the user sets sriov_numvfs to zero prior to unbinding the
device.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull power management and ACPI updates from Rafael Wysocki:
 "From the number of commits perspective, the biggest items are ACPICA
  and cpufreq changes with the latter taking the lead (over 50 commits).

  On the cpufreq front, there are many cleanups and minor fixes in the
  core and governors, driver updates etc.  We also have a new cpufreq
  driver for Mediatek MT8173 chips.

  ACPICA mostly updates its debug infrastructure and adds a number of
  fixes and cleanups for a good measure.

  The Operating Performance Points (OPP) framework is updated with new
  DT bindings and support for them among other things.

  We have a few updates of the generic power domains framework and a
  reorganization of the ACPI device enumeration code and bus type
  operations.

  And a lot of fixes and cleanups all over.

  Included is one branch from the MFD tree as it contains some
  PM-related driver core and ACPI PM changes a few other commits are
  based on.

  Specifics:

   - ACPICA update to upstream revision 20150818 including method
     tracing extensions to allow more in-depth AML debugging in the
     kernel and a number of assorted fixes and cleanups (Bob Moore, Lv
     Zheng, Markus Elfring).

   - ACPI sysfs code updates and a documentation update related to AML
     method tracing (Lv Zheng).

   - ACPI EC driver fix related to serialized evaluations of _Qxx
     methods and ACPI tools updates allowing the EC userspace tool to be
     built from the kernel source (Lv Zheng).

   - ACPI processor driver updates preparing it for future introduction
     of CPPC support and ACPI PCC mailbox driver updates (Ashwin
     Chaugule).

   - ACPI interrupts enumeration fix for a regression related to the
     handling of IRQ attribute conflicts between MADT and the ACPI
     namespace (Jiang Liu).

   - Fixes related to ACPI device PM (Mika Westerberg, Srinidhi
     Kasagar).

   - ACPI device registration code reorganization to separate the
     sysfs-related code and bus type operations from the rest (Rafael J
     Wysocki).

   - Assorted cleanups in the ACPI core (Jarkko Nikula, Mathias Krause,
     Andy Shevchenko, Rafael J Wysocki, Nicolas Iooss).

   - ACPI cpufreq driver and ia64 cpufreq driver fixes and cleanups (Pan
     Xinhui, Rafael J Wysocki).

   - cpufreq core cleanups on top of the previous changes allowing it to
     preseve its sysfs directories over system suspend/resume (Viresh
     Kumar, Rafael J Wysocki, Sebastian Andrzej Siewior).

   - cpufreq fixes and cleanups related to governors (Viresh Kumar).

   - cpufreq updates (core and the cpufreq-dt driver) related to the
     turbo/boost mode support (Viresh Kumar, Bartlomiej Zolnierkiewicz).

   - New DT bindings for Operating Performance Points (OPP), support for
     them in the OPP framework and in the cpufreq-dt driver plus related
     OPP framework fixes and cleanups (Viresh Kumar).

   - cpufreq powernv driver updates (Shilpasri G Bhat).

   - New cpufreq driver for Mediatek MT8173 (Pi-Cheng Chen).

   - Assorted cpufreq driver (speedstep-lib, sfi, integrator) cleanups
     and fixes (Abhilash Jindal, Andrzej Hajda, Cristian Ardelean).

   - intel_pstate driver updates including Skylake-S support, support
     for enabling HW P-states per CPU and an additional vendor bypass
     list entry (Kristen Carlson Accardi, Chen Yu, Ethan Zhao).

   - cpuidle core fixes related to the handling of coupled idle states
     (Xunlei Pang).

   - intel_idle driver updates including Skylake Client support and
     support for freeze-mode-specific idle states (Len Brown).

   - Driver core updates related to power management (Andy Shevchenko,
     Rafael J Wysocki).

   - Generic power domains framework fixes and cleanups (Jon Hunter,
     Geert Uytterhoeven, Rajendra Nayak, Ulf Hansson).

   - Device PM QoS framework update to allow the latency tolerance
     setting to be exposed to user space via sysfs (Mika Westerberg).

   - devfreq support for PPMUv2 in Exynos5433 and a fix for an incorrect
     exynos-ppmu DT binding (Chanwoo Choi, Javier Martinez Canillas).

   - System sleep support updates (Alan Stern, Len Brown, SungEun Kim).

   - rockchip-io AVS support updates (Heiko Stuebner).

   - PM core clocks support fixup (Colin Ian King).

   - Power capping RAPL driver update including support for Skylake H/S
     and Broadwell-H (Radivoje Jovanovic, Seiichi Ikarashi).

   - Generic device properties framework fixes related to the handling
     of static (driver-provided) property sets (Andy Shevchenko).

   - turbostat and cpupower updates (Len Brown, Shilpasri G Bhat,
     Shreyas B Prabhu)"

* tag 'pm+acpi-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (180 commits)
  cpufreq: speedstep-lib: Use monotonic clock
  cpufreq: powernv: Increase the verbosity of OCC console messages
  cpufreq: sfi: use kmemdup rather than duplicating its implementation
  cpufreq: drop !cpufreq_driver check from cpufreq_parse_governor()
  cpufreq: rename cpufreq_real_policy as cpufreq_user_policy
  cpufreq: remove redundant 'policy' field from user_policy
  cpufreq: remove redundant 'governor' field from user_policy
  cpufreq: update user_policy.* on success
  cpufreq: use memcpy() to copy policy
  cpufreq: remove redundant CPUFREQ_INCOMPATIBLE notifier event
  cpufreq: mediatek: Add MT8173 cpufreq driver
  dt-bindings: mediatek: Add MT8173 CPU DVFS clock bindings
  PM / Domains: Fix typo in description of genpd_dev_pm_detach()
  PM / Domains: Remove unusable governor dummies
  PM / Domains: Make pm_genpd_init() available to modules
  PM / domains: Align column headers and data in pm_genpd_summary output
  powercap / RAPL: disable the 2nd power limit properly
  tools: cpupower: Fix error when running cpupower monitor
  PM / OPP: Drop unlikely before IS_ERR(_OR_NULL)
  PM / OPP: Fix static checker warning (broken 64bit big endian systems)
  ...

Pull devicetree updates from Rob Herring:
 - added Frank Rowand as DT maintainer in preparation for Grant's
   retirement.
 - generic MSI binding documentation and a few other minor doc updates
 - fix long standing issue with DT platorm device unregistration
 - fix loop forever bug in of_find_matching_node_by_address()

* tag 'devicetree-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  MAINTAINERS: Add Frank Rowand as DT maintainer
  mtd: nand: pxa3xx: add optional dma for pxa architecture
  Documentation: DT: cpsw: document missing compatible
  Docs: dt: add generic MSI bindings
  drivercore: Fix unregistration path of platform devices
  of/address: Don't loop forever in of_find_matching_node_by_address().
  of: Add vendor prefix for JEDEC Solid State Technology Association
  of/platform: add function to populate default bus
  of: Add vendor prefix for Sharp Corporation

Pull trivial tree updates from Jiri Kosina:
 "The usual stuff from trivial tree for 4.3 (kerneldoc updates, printk()
  fixes, Documentation and MAINTAINERS updates)"

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
  MAINTAINERS: update my e-mail address
  mod_devicetable: add space before */
  scsi: a100u2w: trivial typo in printk
  i2c: Fix typo in i2c-bfin-twi.c
  treewide: fix typos in comment blocks
  Doc: fix trivial typo in SubmittingPatches
  proportions: Spelling s/consitent/consistent/
  dm: Spelling s/consitent/consistent/
  aic7xxx: Fix typo in error message
  pcmcia: Fix typo in locking documentation
  scsi/arcmsr: Fix typos in error log
  drm/nouveau/gr: Fix typo in nv10.c
  [SCSI] Fix printk typos in drivers/scsi
  staging: comedi: Grammar s/Enable support a/Enable support for a/
  Btrfs: Spelling s/consitent/consistent/
  README: GTK+ is a acronym
  ASoC: omap: Fix typo in config option description
  mm: tlb.c: Fix error message
  ntfs: super.c: Fix error log
  fix typo in Documentation/SubmittingPatches
  ...

Pull livepatching fix from Jiri Kosina:
 "Livepatching error handling fix"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching:
  livepatch: Improve error handling in klp_disable_func()

Pull HID updates from Jiri Kosina:
 "to receive patches queued for 4.3 merge window in HID tree. Highlights:

   - a lot of improvements (regarding supported features and devices) to
     Wacom driver, from Aaron Skomra and Jason Gerecke
   - a lot of functional fixes and support for large I2C transfer to
     cp2112 driver, from Ellen Wang
   - HW support improvements to RMI driver, from Andrew Duggan
   - quite some small fixes and device ID additions all over the place"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (44 commits)
  HID: wacom: wacom_setup_numbered_buttons is local to wacom_wac
  HID: wacom: Add support for Express Key Remote.
  HID: wacom: Set button bits based on a new numbered_buttons
  HID: quirks: add QUIRK_NOGET for an other TPV touchscreen
  HID: usbhid: Fix the check for HID_RESET_PENDING in hid_io_error
  HID: i2c-hid: Only disable irq wake if it was successfully enabled during suspend
  HID: wacom: Use tablet-provided touch height/width values for INTUOSHT
  HID: gembird: add new driver to fix Gembird JPD-DualForce 2
  HID: lenovo: Hide middle-button press until release
  HID: lenovo: Add missing return-value check
  HID: lenovo: Use constants for axes names
  HID: wacom: Simplify 'wacom_pl_irq'
  HID: wacom: Do not repeatedly attempt to set device mode on error
  HID: wacom: Do not repeatedly attempt to set device mode on error
  HID: wacom: Remove WACOM_QUIRK_NO_INPUT
  HID: wacom: Replace WACOM_QUIRK_MONITOR with WACOM_DEVICETYPE_WL_MONITOR
  HID: wacom: Use calculated pkglen for wireless touch interface
  HID: sony: Fix DS4 controller reporting rate issues
  HID: chicony: Add support for Acer Aspire Switch 12
  HID: hid-lg: Add USBID for Logitech G29 Wheel
  ...

Pull EDAC fixes from Borislav Petkov:
 "Two minor fixlets this time: AMD MCE decoding correction and
  xgene_edac cleanup"

* tag 'edac_for_4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
  EDAC, mce_amd: Don't emit 'CE' for Deferred error
  EDAC, xgene: Drop owner assignment from platform_driver

Resolve warnings resulting from redundant initialization of the
get_bus_info field in the mac_ops_X550* structures.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When unbinding an SR-IOV device with VFs configured from ixgbe, the
driver behaves in one of two ways.  If max_vfs was specified, the
SR-IOV state is disabled, removing the VFs.  The occurs regardless of
whether the VF count was later modified through sysfs.  If however
max_vfs is zero, such as by not specifying the module parameter, the
VFs persist after the PF is unbound from ixgbe.  If the PF is then
bound to vfio-pci to be assigned to a VM, the PF is non-functional.

>From the comment, commit da36b647 ("ixgbe: Implement PCI SR-IOV
sysfs callback operation") clearly intended this alternate behavior,
but probably didn't realize the PF doesn't work in this mode.

This bimodal behavior is confusing to users and results in a state
where the PF is broken for other uses unless the user sets
sriov_numvfs to zero prior to unbinding the device.  Remove this
behavior so that VFs are removed and the PF is functional for other
uses after unbind, regardless of the way VFs are enabled.
Signed-off-by: NAlex Williamson <alex.williamson@redhat.com>
Acked-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Now that we can do 2.5G link speed, we need to be able to report it.
Also change the nested triadic involved in creating the log message
to instead use a simpler switch statement to set a string pointer.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch resolves an issue where users were not able to dynamically
set number of queues for 82598 via ethtool -L
Reported-by: NTal Abudi <talabudi@gmail.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Allows to change the rxfh indirection table and/or key using
ethtool interface.
Signed-off-by: NTom Barbette <tom.barbette@ulg.ac.be>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Avoid a needless PHY access on copper phys to save the 10ms wait
time for each PHY access. A helper function is introduced to
actually do the register access and process the contents.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We already cache this FW/SW semaphore mask so might as well use it
for consistency.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch removes the redundant lan_id in the phy struct and uses
the bus version.  Both variables exist and intend to represent the
STATUS register LAN_ID field.  However, phy.lan_id is not bit shifted
so the phy.lan_id = 0x0 for LAN Id 0 and phy.lan_id = 0x4 for LAN Id 1.
Where bus.lan_id is bit shifted so bus.lan_id = 0x0 for LAN Id 0 and
bus.lan_id = 0x1 for LAN Id 1. There seems no need for the additional
lan_id variable and this should make the code less confusing.
Signed-off-by: NDonald C Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>