This patch adds Multi channel support on Renesas R-Car sound.
This patch is tested on Salvator-X board, but it can't use
Multi channel, because supported format is different between
codec chip and R-Car.
Thus, it was tested on board which doesn't mount codec chip,
with oscilloscope.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NMark Brown <broonie@kernel.org>

L/R channel data has been treated as inverted on R-Car sound 16bit mode,
Thus, 4689032b("ASoC: rsnd: tidyup data align position") tidyuped data
align position. But it couldn't care about capture case. This patch
cares both playback/capture
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Renesas R-Car can out TDM by
1) 6ch x 1 DAI as TDM Extend Mode
2) 2ch x 4 x 1 DAI as TDM split Mode
3) 2ch x 3 DAI or
   2ch x 4 DAI as TDM Multichannel Mode

This patch adds 1) TDM Extend Mode. Because of HW design,
this 6ch data will be outputed via 8ch data width.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current DVC is assuming that the sound is always stereo.
This patch makes it more flexible
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

SRC_BUSIF_MODE has both IN/OUT register. Current src driver sets
IN register only. This patch sets missing OUT register.
IN/OUT register are using default setting, so, there is no
HW effect.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current rsnd driver is indicating how to use regmap debug method
on gen.c comment area.
regmap debug method indicates address and value, but rsnd driver is
using too many IPs (SSI/SSIU/SRC/CTU/MIX/DVC/CMD), and address.
Thus, we would like to know more useful information for debugging.
This patch indicates address name for debugging.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current Renesas sound driver requests struct platform_device on
probe/remove for each modules. But driver can get it by
rsnd_priv_to_pdev(). This patch removes unnecessary parameter
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

No board is using Renesas sound driver via platform boot now.
This means all user is using DT boot. Platform boot support is
no longer needed. But, it strongly depends on platform boot style.
Now, platform boot style was removed from driver.
This is cleanup patch, and remove pointless struct rsnd_of_data
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

No board is using Renesas sound driver via platform boot now.
This means all user is using DT boot. Platform boot support is
no longer needed. But, it strongly depends on platform boot style.
This patch removes platform boot support from gen.c
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

This patch removes SRC Gen1 support which has no user on upstream.
Historically, SRC Gen1 was created as prepare for SRC Gen2 support.
It works well for Gen2 support, but Gen1 is not same as Gen2.
So now, Gen1 support is no longer needed. Thanks Gen1 and Bye-bye.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

struct rsnd_gen :: res array size should be RSND_BASE_MAX,
not RSND_REG_MAX. This patch fixup it, and indicates whether
each data array size is based on what
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

debug meesage for rsnd_mod_read() should be prints after read
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

This patch adds MIX (Mixer) initial support for rsnd driver.
It is assuming that this MIX is used via DPCM.

This is sample code for playback.

	CPU0  : [MEM] -> [SRC1] -> [CTU02] -+
					    |
					    +-> [MIX0] -> [DVC0] -> [SSI0]
	                                    |
	CPU1  : [MEM] -> [SRC2] -> [CTU03] -+

	sound {
		compatible = "renesas,rsrc-card";

		...

		cpu@0 {
			sound-dai = <&rcar_sound 0>;
		};

		cpu@1 {
			sound-dai = <&rcar_sound 1>;
		};

		codec {
			...
		};
	};

	rcar_sound {

		...

		rcar_sound,dai {
			dai0 {
				playback = <&src1 &ctu02 &mix0 &dvc0 &ssi0>;
			};
			dai1 {
				playback = <&src2 &ctu03 &mix0 &dvc0 &ssi0>;
			};
		};
	};
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: NKeita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

This patch adds CTU (Channel Transfer Unit) support for rsnd driver.
But, it does nothing to data at this point, but is required for MIX
support.

CTU design is a little different from other IPs (CTU0 is including
CTU00 - CTU03, and CTU1 is including CTU10 - CTU13, these have different
register mapping) We need to care about it on this driver.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: NKeita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Sound L/R order of SSI is different from Linux sound data order.
So current rsnd driver is using DALIGN (= data align) to exchange data
align on SSIU. OTOH, CMD/SRC/SSIU have DALIGN register. Now inverted
sound volume will be exchanged if user used volume control on DVC.
Because SSIU which exchanges data align is located after DVC.

	MEM -> SRC -> DVC -> SSI

This patch exchanges data align SRC if possible
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: NKeita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

based on datasheet
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: NKeita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

based on datasheet
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: NKeita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

rsnd_force_write() is similar to rsnd_write(),
but rsnd_force_write() write data to register even though
it is same value.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

This patch removes useless debug message. especially some kind of
"probed" message will be printed from core.c if it has #define DEBUG
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Renesas sound driver needs SSI/SRC/DVC regmaps, but it didn't have
regmap_config::name for devm_regmap_init_mmio().
Thus, debugfs initialization code tried to use same driver name
many times, and failed.
This patch adds eacy own name for regmap_config::name
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Now, we have dma.c for Audio DMAC / Audio DMAC peri peri.
rsnd_gen_dma_addr() should go there.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

physical address is required from Audio DMAC peri peri.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

rsnd driver needs to support Audio DMAC peri peri inside sound driver.
getting resource by name is useful for it
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

L/R channel will be switched if under/over flow error happen on
Renesas R-Car sound device by the HW bugs. Then, HW restart is required
for salvage. This patch add salvage support for SRC.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

This patch adds Volume Ramp to Renesas sound driver.

amixer set "DVC Out" 100%
amixer set "DVC Out Ramp Up Rate"   "0.125 dB/64 steps"
amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
amixer set "DVC Out Ramp" on
aplay xxx.wav &
amixer set "DVC Out"  80%  // Volume Down
amixer set "DVC Out" 100%  // Volume Up
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current Renesas R-Car sound driver debug message
is using random format
(ex "ssi0: xxx" / "SSI0 xxx" / "ssi[0]: xxx")
and confusable timing
("xxx probe failed" and "xxx probed" are shown in same time)
This patch fixes these
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

b8c63786
(ASoC: rsnd: use regmap_mmio instead of original regmap bus)
added regmap_mmio support on Renesas R-Car sound driver.
Then, debug information of register read/write
indicates regmap index, not register address.
This is a little bit confusable information.
This patch tidyup debug message, and added regmap debug hint
on comment area.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Sparse spits out the following warning:
	sound/soc/sh/rcar/gen.c:250:21: warning: dubious: x & !y

It does this because sometimes mixing boolean and bit-wise logic has not the
intended result. In this case we are fine, but replacing the bit-wise '&' with
the boolean '&&' silences the sparse warning. The generated code for both cases
is the same.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

b8c63786
(ASoC: rsnd: use regmap_mmio instead of original regmap bus)
used regmap_mmio and modified dev_dbg() for rsnd_read/write().
But rsnd_bset() is missing it.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

R-Car sound uses Audio Local Bus which uses Lch/Rch format.
This bus is used if driver uses BUSIF.
But sound data is written as Rch/Lch format in register.
This means Rch <-> Lch will be inverted.
SSIU :: BUSIF_DALIGN is used to controlling data format.
Reported-by: NJun Watanabe <jun.watanabe.ue@renesas.com>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Current rsnd driver is using regmap and regmap_field.
It used original regmap bus which is
single regmap instance for multi register mapping.
This patch modifies it to use regmap_mmio bus,
and tidyuped probe method
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Current R-Car sound SSI/SRC/DVC selection has feature limit.
(It is assuming that SSI/SRC are using same index number)

So that enabling SSI/SRC flexible selection,
this patch modifies DMA settings.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Sound data needs to be sent to R-Car sound SSI when playback.
But, there are 2 interfaces for it.
1st is SSITDR/SSIRDR which are mapped on SSI.
2nd is SSIn_BUSIF which are mapped on SSIU.

2nd SSIn_BUSIF is used when DMA transfer,
and it is always used if sound data came from via SRC.
But, we can use it when SSI+DMA case too.
(Current driver is assuming 1st SSITDR/SSIRDR for it)

2nd SSIn_BUSIF can be used as FIFO.
This is very helpful/useful for SSI+DMA.

But DMA address / DMA ID are not same between 1st/2nd cases.
This patch care about these settings.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

ad32d0c7
(ASoC: rsnd: add rsnd_gen_dma_addr() for DMAC addr)
added rsnd_gen_dma_addr() to calculate DMA addr,
but, it is necessary only for Gen2.
This patch ignores Gen1 case.
Kernel will be panic without this patch.
Special thanks to Simon
Reported-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NMark Brown <broonie@linaro.org>

The DMAC src/dst addr needs to be set from driver when DT case.
(It was set from SoC/DMAEngine code when non-DT case)
This patch adds rsnd_gen_dma_addr() to set DMAC src/dst addr.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Use the %pap printk specifier to print resource_size_t variables. This
fixes warnings on platforms where resource_size_t has a different size
than int.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

This patch adds DVC (Digital Volume Controller)
support which is member of CMD unit.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Support for loading the Renesas R-Car sound driver via DeviceTree.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Now, rsnd_xxx_remove() do nothing.
remove these
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>