This patch adds Multi channel support on Renesas R-Car sound.
This patch is tested on Salvator-X board, but it can't use
Multi channel, because supported format is different between
codec chip and R-Car.
Thus, it was tested on board which doesn't mount codec chip,
with oscilloscope.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NMark Brown <broonie@kernel.org>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current rsnd driver is using complex macro to parse DAI connection.
This patch adds new rsnd_parse_connect_common() and replace current
macro to it.
This is prepare for multi channel support
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

TDM will use 6 or 8 slots on 1 SSI, and Multi channel will use
6 or 8 slots on few SSI (each SSI uses 2 slots).
Thus, this adds new slot control functions which can be prepare
for Multi channel support.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

rsnd_get_slot_rdai() returns total slots (it returns 6 if total 6
channels) , and rsnd_get_slot_extend() returns extended SSI width
(it returns 8 if total 6 channels). This will be used on SSI multi
channel support too (It will return 2 if total 6 channels with 3 SSI).
But, it is using confusable naming.
This patch changes rsnd_get_slot_rdai() -> rsnd_get_slot(),
rsnd_get_slot_extend() -> rsnd_get_slot_width()
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current Renesas sound driver is using rsnd_get_slot_runtime(), but
it is same as runtime->channels. This patch removes
rsnd_get_slot_runtime()
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current SSI/SSIU are using rsnd_get_slot_runtime() to check TDM,
but using rsnd_get_slot_extend() is more sane.
This patch fix it up
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

It can't output corrent dma name *before* rsnd_mod_init().
It goes to *after* rsnd_mod_init() by this patch
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Renesas sound driver has rsnd_get_adinr_bit/chan() functions.
It is assuming _bit() returns ADINR :: OTBL,
and _chan() returns ADINR :: CHNUM.
Current _bit() returns both OTBL and CHNUM. This patch fixup it.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

SSIU should be controlled after SSI. This patch fix up it
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

rsrc-card is DPCM supported version of simple-card. Thus it has similar
DT format. OTOH, snd_soc_dai_link requests cpu/codec, but one of them
will be snd-soc-dummy in DPCM case, and DPCM requests frontend/backend
dai_link. This means it might have multi backend/codec.
And, SND_SOC_DAIFMT_xxx is based on "codec". Because of these
difference, current rsrc card can't detect correct dai_fmt.
This patch detect correct dai fmt from 1st "codec".
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

1efb53a2 ("ASoC: simple-card: Remove support for setting differing
DAI formats") removed set_fmt support from simple-card.
rsrc-card follows same style, because it is based on simple-card.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Renesas sound driver will use tdm slot on TDM Multi Mode support.
This patch enables tdm slot on rsrc card driver on DT.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

We use ret as the return value from the rsnd_mix_probe() but if there
are no child nodes and no errors then we will never initialize ret leading
to build warnings. Ensure ret is initialized before we iterate over the
child nodes to avoid this.
Signed-off-by: NMark Brown <broonie@kernel.org>

We use ret as the return value from the rsnd_dvc_probe() but if there
are no child nodes and no errors then we will never initialize ret leading
to build warnings. Ensure ret is initialized before we iterate over the
child nodes to avoid this.
Signed-off-by: NMark Brown <broonie@kernel.org>

We use ret as the return value from the rsnd_ctu_probe() but if there
are no child nodes and no errors then we will never initialize ret leading
to build warnings. Ensure ret is initialized before we iterate over the
child nodes to avoid this.
Signed-off-by: NMark Brown <broonie@kernel.org>

L/R channel data has been treated as inverted on R-Car sound 16bit mode,
Thus, 4689032b("ASoC: rsnd: tidyup data align position") tidyuped data
align position. But it couldn't care about capture case. This patch
cares both playback/capture
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

SSICR::SWSP bit controls WS signal low/high, but in case of TDM
it is inverted. This patch solves this issue.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

This patch adds missing check of snd_soc_of_get_dai_name().
It might not be able to use sound card, because it might returns
-EPROBE_DEFER.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

drv pointer should be "base + offset" instead of
"current + offset". This patch fixup this issue, otherwise
third and subsequent pointer will be broken
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Renesas R-Car can out TDM by
1) 6ch x 1 DAI as TDM Extend Mode
2) 2ch x 4 x 1 DAI as TDM split Mode
3) 2ch x 3 DAI or
   2ch x 4 DAI as TDM Multichannel Mode

This patch adds 1) TDM Extend Mode. Because of HW design,
this 6ch data will be outputed via 8ch data width.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current DVC is assuming that the sound is always stereo.
This patch makes it more flexible
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current SSI is assuming that the sound is always stereo. But, SSI needs
to calculate its frequency when master mode. Then This frequency depends
on each SSI's slots, and TDM mode (= TDM Extend Mode, TDM split Mode,
TDM Multichannel Mode).
This patch enables to use non-stereo sound.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

It will have TDM settings on SSIWSR. Actually, we would like to set
it on rsnd_ssi_config_init(), but we can't. Because SSI might be used
as clock master (It doesn't need to call rsnd_ssi_config_init() when
clock master mode).
This patch adds new ssi->wsr and set it on rsnd_ssi_start().
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

In order to enhance code readability, this patch adds
rsnd_ssi_config_init() and moves SSICR register settings to it.
This is prepare patch for TDM support
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Based on datasheet process
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Based on datasheet process
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Based on datasheet process
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Based on datasheet naming
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Based on datasheet naming
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Based on datasheet naming
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

SRC_BUSIF_MODE has both IN/OUT register. Current src driver sets
IN register only. This patch sets missing OUT register.
IN/OUT register are using default setting, so, there is no
HW effect.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

DVC/SRC/SSIU needs ADINR::CHNUM settings too. This patch adds
these missing value.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

adg.c is used from ssi/src/cmd. Thus don't use confusable *mod here.
This patch rename it to ssi_mod/src_mod/cmd_mod
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Simply document new compat strings.
There appears to be no need for a driver updates.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Acked-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

rsnd_ssi_record_error() should recorde error, but it clears error too.
this patch fixes up semantic of rsnd_ssi_record_error that it records
error but doesn't clear error.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

rsnd_src_error_record() should recorde error, but it clears error too.
this patch fixes up semantic of rsnd_src_error_record that it records
error but doesn't clear error.
And this patch renames
rsnd_src_error_clear()  to rsnd_src_status_clear()
rsnd_src_error_record() to rsnd_src_record_error()
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current rsnd driver is indicating how to use regmap debug method
on gen.c comment area.
regmap debug method indicates address and value, but rsnd driver is
using too many IPs (SSI/SSIU/SRC/CTU/MIX/DVC/CMD), and address.
Thus, we would like to know more useful information for debugging.
This patch indicates address name for debugging.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>