Current code does not check whether main_work_queue or
rx_work_queue is running when preparing to do queue_work,
this code fix add check before calling queue_work, reducing
unnecessary queue_work switch.

This change instead sets more_task flag to ensure we run main_process
superloop once again.
Signed-off-by: NShengzhen Li <szli@marvell.com>
Signed-off-by: NZhaoyang Liu <liuzy@marvell.com>
Reviewed-by: NCathy Luo <cluo@marvell.com>
Reviewed-by: NAmitkumar Karwar <akarwar@marvell.com>
Reviewed-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

SD8897 support buffers of 4K and 16 such ports can be accomodated.
So basically 64K buffer size in single aggregation is supported.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Rename this function to reflect its purpose correctly.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

A crash was detected while changing virtual interface type is in
progress. This was tracked to race condition in accessing bss_priority
table while change is in progress. This patch ensures that main_process
and rx_process works are locked while we change virtual interface.
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

In struct wl18xx_acx_rx_rate_stat, rx_frames_per_rates field is an
array, not a number.  This means WL18XX_DEBUGFS_FWSTATS_FILE can't be
used to display this field in debugfs (it would display a pointer, not
the actual data).  Use WL18XX_DEBUGFS_FWSTATS_FILE_ARRAY instead.

This bug has been found by adding a __printf attribute to
wl1271_format_buffer.  gcc complained about "format '%u' expects
argument of type 'unsigned int', but argument 5 has type 'u32 *'".

Fixes: c5d94169 ("wl18xx: use new fw stats structures")
Signed-off-by: NNicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

I have here FRITZ!WLAN USB Stick N v2 / idVendor=057c, idProduct=8501
and every single of this requests ends up with:

|ieee80211 phy0: rt2x00usb_vendor_request: Error - Vendor Request 0x0c  failed for offset 0x0000 with error -32

I was browsing the the vedor code and I haven't seen such request so I
remove it with this patch. If I wasn't look enough or if this error is
expected then please excuse :)
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

rt2800usb_autorun_detect() blindly assumes assumes that it worked while
it could have failed. Check the error code here.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

My understanding ist that rt2x00usb_register_read() is void and so the
reader is unaware of read errors and assumes that whatever was on the
stack as it was about to read.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

We might be in interrupt context at few places. So replace
del_timer_sync() with del_timer(). This patch fixes a kernel
trace problem seen occasionally during our testing.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds support for auto ARP feature in mwifiex.
The device will respond to ARP requests from the network
with ARP response in suspended state without waking up the host.
This feature is enabled in the driver by default.
Signed-off-by: NMaithili Hinge <maithili@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

It's been observed Rx aggregated packets are always followed
by a single Rx packet. This patch improves our logic to add
that extra packet in next aggregation.
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This function is used only by rtl8821ae so move it there
Signed-off-by: NPriit Laes <plaes@plaes.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NPriit Laes <plaes@plaes.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

In HT40 modes, pulse events on primary and extension
channel are processed individually. If valid, a pulse
event will be fed into the detector
* for primary frequency, or
* for extension frequency (+/-20MHz based on HT40-mode)
* or both

With that, a 40MHz radar will result in two individual
radar events.
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

To support HT40 DFS mode, a triggering detector must
reset only itself but not other detector lines.
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This reverts commit b09f5ec1.

Now that we have fully working BCMA_DRIVER_PCI symbol (in can be safely
disabled), there is no risk bcma will try to use PCI code without PCI
available.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

It isn't required for bcma bus on SoCs, so provide some empty functions
and allow disabling it.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This function isn't really related to any bus core. It touches PCI
device config registers only, so move it to the (PCI) host file.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Remove unnecessary parameter in rtl8192cu/hw.c
Signed-off-by: NTaehee Yoo <ap420073@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r@
type T;
identifier f;
@@

static T f (...) { ... }

@@
identifier r.f;
declarer name EXPORT_SYMBOL_GPL;
@@

-EXPORT_SYMBOL_GPL(f);
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The watchdog timer is used to put the device in a low-power mode when
it is idle for some time. This timer is stopped during that mode and
should be restarted upon activity. This has been broken by commit
d4150fced0365 ("brcmfmac: Simplify watchdog sleep."). This patch
restores the behaviour as it was before that commit.
Reported-by: NPontus Fuchs <pontusf@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The firmware provides pointer to SDIO shared information at end of
RAM during firmware initialization. End of RAM is obviously determined
by the actual ram size, but part of that may be used for save&restore
memory. In that case another location in RAM will hold the pointer.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Instead of hard-coded memory sizes it is possible to obtain that
information from the internal memory registers.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Make the brcmf_chip_attach() function responsible for putting the
device in a state where it is accessible for firmware download.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The functions brcmf_chip_[enter/exit]_download() are not exclusively
used for firmware download so rename these more appropriate.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Instead of checking the cores in the chip only if CONFIG_BRCMDBG
is selected perform the check always and extend it with more sanity
checking.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Removing the ramsize from the brcmf_sdio structure to avoid
duplication. The information is available in brcmf_chip
structure.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

pre-requisite to shrink size of ieee80211_tx_info which in turn is
needed to shrink skb->cb to 40 bytes again.
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

If we want to shrink skb->cb then we'd have to see about
reducing struct ieee80211_tx_info, which gets embedded inside
skb->cb[].

It provides a scratch space to be used by wireless drivers.
ar5523 uses the maximum space available today (40 bytes), but it seems
we don't need this -- data->skb pointer seems to always point back to the
skb whose cb buffer the data structure resides, iow, given a pointer to the
embedded control buffer we can infer the skb address.
Tested-by: NPontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Since the RTT registers need to be configured for all
valid chains irrespective of the runtime chainmask,
use the actual chainmask of the chip.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When assigning the initvals for PCIE sleep/awake
registers, check the configuration that has been
assigned to pll_pwrsave during initialization. Also,
display a warning if we don't have valid arrays.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Cards based on AR9462/AR9565 support more PCIE
power save mechanisms, so register them correctly.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Use the value in ah->config.pll_pwrsave to determine
which array needs to be loaded. Also, initialize
pll_pwrsave to 1 by default.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

These will be used to handle chip-specific
power save configuration.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

For the AP, configuration may say not to bridge traffic between
wireless clients. This is conveyed from user space (ex: hostapd has
ap_isolate parameter) with NL80211_CMD_SET_BSS, to the driver's
cfg80211 ops method change_bss

Add support for this setting.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This is for AP only. If Rx data frame targeted to one of associated clients,
transmit it back to the wireless media and don't deliver to the host.
For the multicast frames, deliver to both host and wireless media.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

It is expected that driver completes NAPI when less than
full budget is consumed.

Fulfill this requirement.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

These changes add support for BCM4345 SDIO chipset.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: NSyed Asifful Dayyan <syedd@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Msgbuf is using a wait_event_timeout to wait for the response on
an ioctl. The wakeup routine uses waitqueue_active to see if
wait_event_timeout has been called. There is a chance that the
response arrives before wait_event_timeout is called, this
will result in situation that wait_event_timeout never gets
woken again and assumed result will be a timeout. This patch
removes that errornous situation by always setting the
ctl_completed var before checking for queue active.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>