Use the value in ah->config.pll_pwrsave to determine
which array needs to be loaded. Also, initialize
pll_pwrsave to 1 by default.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Registering the card as a wakeup source needs to
be done once, during initialization. When the WOW
configuration changes, the card's status as wakeup
source needs to be changed too and this is done
via the set_wakeup() callback. Also, make sure
the device is removed properly using ath9k_deinit_wow().
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

ath9k and ath9k_htc use the variable name "led_blink" to indicate
whether the module parameter "blink" is on. This name is easy to
conflict with other variables, and has caused a compiler error found
by kbuild test bot. The compiler error is as following:

drivers/net/wireless/ath/ath9k/ath9k_htc.o:(.data+0x47c): multiple definition of `led_blink'
drivers/net/wireless/ath/ath9k/ath9k.o:(.bss+0x20): first defined here

Fixes: 3a939a67 ("ath9k_htc: Add a module parameter to disable blink")
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NHong Xu <hong@topbug.net>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

IRQs are suppressed if ah == NULL and ATH_OP_INVALID being set in
common->op_flags. Close a short time window between those two.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On some x86 platforms, the LED gpio is active high
instead of active low. Identify such cards and modify
the GPIO usage to make sure LED works properly.

Cc: Russell Hu <rhu@qca.qualcomm.com>
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

drivers/net/wireless/ath/ath9k/init.c:91:6: sparse: symbol 'ath9k_op_ps_wakeup' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/init.c:96:6: sparse: symbol 'ath9k_op_ps_restore' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/init.c:101:19: sparse: symbol 'ath9k_ps_ops' was not declared. Should it be static?
Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

spectral code mostly depends on ath_hw, not on ath_softc
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Track it per channel context instead of in the softc
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some devices have multiple bands enables in the EEPROM data, even though
they are only calibrated for one. Allow platform data to disable
unsupported bands.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On some devices (especially little-endian ones), the flash EEPROM data
has a different endian, which needs to be detected.
Add a flag to the platform data to allow overriding that behavior
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The initvals use up quite a bit of space, and PC-OEM support is
typically not needed on embedded systems
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enabling HW queue control for normal (non-mcc) mode
causes problems with queue management, resulting
in traffic stall. Since it is mainly required for
fairness in MCC mode, disable it for the general case.

Bug: https://dev.openwrt.org/ticket/18164

Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reduces code duplication.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since CTWindow can be used for improving discoverability,
fill this field in the NoA Attribute properly.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is no reason why managed/p2p interfaces have to
be limited to one. IBSS is the only type that needs
a restriction.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds a routine to setup the offchannel
instance in ath_softc.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Setup the offchannel/sched timers and the chanctx work
inside the new function.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch ensures that the module parameter "use_chanctx" is
visible only when CONFIG_ATH9K_CHANNEL_CONTEXT is selected.
Also register the channel context callbacks with mac80211 only
when it is explicitly enabled and compile them out of the driver
when CONFIG_ATH9K_CHANNEL_CONTEXT is not selected.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use CONFIG_ATH9K_CHANNEL_CONTEXT to conditionally
compile P2P-PS code.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Earlier the listen interval is used to decide switching between
operating and off-channels during bgscan and to improve throughput,
the listen interval is reduced to 1. After optimiztion in scan
state machine, listen period is not used for decision making and
hence reverting it back to original value.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use seperate tx queue for each AC in each channel context and expose
these information to mac80211 to avoid stopping one channel context
leads to stopping the entire traffic for that AC even on other contexts.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Configure the TSF based hardware timer for a channel switch.
Also set up backup software timer, in case the gen timer fails.
This could be caused by a hardware reset.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add channel context operations (add, remove, change, assign and
unassign) to enable support for multiple channels.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add remain on channel support in order to enable multi-channel
concurrency.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Implement hw_scan support for enabling multi-channel cuncurrency.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The channel context worker is used to switch to next requested
channel context.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The channel context structure is defined to enable
multi-channel concurrency support.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently mac80211 does not support WDS and DFS with channel context
drivers. So advertise these features only when the driver is not
supporting channel context and modparam "use_chanctx" is introduced
for preparing channel context support in ath9k.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add a new platform data flag "use_eeprom" that indicates that the eeprom
found on the card itself should be used instead of the one present in
the platform data.

This allows to override the MAC address of a PCI card while preserving
the eeprom data from the card itself.

The default behavior is preserved.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This will enable AP mode to change channel width dynamically
based on 20/40 intolerance report sent by associated client.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit "ath9k: move sc_flags to ath_common" moved setting
ATH_OP_INVALID flag below ieee80211_register_hw. This is causing
the flag never being cleared randomly as the drv_start is called
prior to setting flag. Fix this by setting the flag prior to
register_hw.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use generic TSF timers to trigger powersave state changes based
information from the P2P NoA attribute.
Opportunistic Powersave is not handled, because the driver does not
support powersave at the moment.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>