Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 03 2月, 2008 4 次提交
  3. 02 2月, 2008 2 次提交
  5. 27 1月, 2008 6 次提交
  7. 26 1月, 2008 8 次提交
  9. 11 1月, 2008 1 次提交
  11. 13 12月, 2007 1 次提交
    • B
      ide: DMA reporting and validity checking fixes (take 3) · 3ab7efe8
      由 Bartlomiej Zolnierkiewicz 提交于 
      * ide_xfer_verbose() fixups:
  - beautify returned mode names
  - fix PIO5 reporting
  - make it return 'const char *'

* Change printk() level from KERN_DEBUG to KERN_INFO in ide_find_dma_mode().

* Add ide_id_dma_bug() helper based on ide_dma_verbose() to check for invalid
  DMA info in identify block.

* Use ide_id_dma_bug() in ide_tune_dma() and ide_driveid_update().

  As a result DMA won't be tuned or will be disabled after tuning if device
  reports inconsistent info about enabled DMA mode (ide_dma_verbose() does the
  same checks while the IDE device is probed by ide-{cd,disk} device driver).

* Remove no longer needed ide_dma_verbose().

This patch should fix the following problem with out-of-sync IDE messages
reported by Nick Warne:

       hdd: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache<7>hdd:
       skipping word 93 validity check
        , UDMA(66)

and later debugged by Mark Lord to be caused by:

        ide_dma_verbose()
                printk( ... "2048kB Cache");
        eighty_ninty_three()
                printk(KERN_DEBUG "%s: skipping word 93 validity check\n");
        ide_dma_verbose()
                printk(", UDMA(66)"

Please note that as a result ide-{cd,disk} device drivers won't report the
DMA speed used but this is intended since now DMA mode being used is always
reported by IDE core code.

v2:
* fixes suggested by Randy:
  - use KERN_CONT for printk()-s in ide-{cd,disk}.c
  - don't remove argument name from ide_xfer_verbose() declaration

v3:
* Remove incorrect check for (id->field_valid & 1) from ide_id_dma_bug()
  (spotted by Sergei).

* "XFER SLOW" -> "PIO SLOW" in ide_xfer_verbose() (suggested by Sergei).

* Fix ide_find_dma_mode() to report the correct mode ('mode' after being
  limited by 'req_mode').

Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Nick Warne <nick@ukfsn.org>
Cc: Mark Lord <lkml@rtr.ca>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      3ab7efe8
  13. 28 11月, 2007 3 次提交
  15. 06 11月, 2007 2 次提交
  17. 27 10月, 2007 1 次提交
  19. 20 10月, 2007 1 次提交
  21. 17 10月, 2007 1 次提交
    • B
      ide: remove ->ide_dma_check (take 2) · 0ae2e178
      由 Bartlomiej Zolnierkiewicz 提交于 
      * Add IDE_HFLAG_TRUST_BIOS_FOR_DMA host flag for host drivers that depend
  on BIOS for programming device/controller for DMA.  Set it in cy82c693,
  generic, ns87415, opti621 and trm290 host drivers.

* Add IDE_HFLAG_VDMA host flag for host drivers using VDMA.  Set it in cs5520
  host driver.

* Teach ide_tune_dma() about IDE_HFLAG_TRUST_BIOS_FOR_DMA flag.

* Add generic ide_dma_check() helper and remove all open coded ->ide_dma_check
  implementations.  Fix all places checking for presence of ->ide_dma_check
  hook to check for ->ide_dma_on instead.

* Remove no longer needed code from config_drive_for_dma().

* Make ide_tune_dma() static.

v2:
* Fix config_drive_for_dma() return values.

* Fix ide-dma.c build for CONFIG_BLK_DEV_IDEDMA_PCI=n by adding
  dummy config_drive_for_dma() inline.

* Fix IDE_HFLAG_TRUST_BIOS_FOR_DMA handling in ide_dma_check().

* Fix init_hwif_it8213() comment.

There should be no functionality changes caused by this patch.

Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      0ae2e178
  23. 13 10月, 2007 6 次提交
    • B
      ide: remove CONFIG_IDEDMA_IVB config option · 76bb7782
      由 Bartlomiej Zolnierkiewicz 提交于 
      Devices which don't set word 93 validation bit should be now handled by
ide-iops.c::ivb_list[] and for debugging purposes cable detection can be
completely overriden with "idex=ata66" parameter.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      76bb7782
    • B
      ide: change master/slave IDENTIFY order · b140b99c
      由 Bartlomiej Zolnierkiewicz 提交于 
      Need to probe slave device first to make it release PDIAG-
(this is required for correct device side cable detection).

Based on libata commit f31f0cc2.

Thanks to Craig for testing this patch.

Cc: Craig Block <chblock3@yahoo.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      b140b99c
    • B
      ide: move ide_config_drive_speed() calls to upper layers (take 2) · 88b2b32b
      由 Bartlomiej Zolnierkiewicz 提交于 
      * Convert {ide_hwif_t,ide_pci_device_t}->host_flag to be u16.

* Add IDE_HFLAG_POST_SET_MODE host flag to indicate the need to program 
  the host for the transfer mode after programming the device.  Set it
  in au1xxx-ide, amd74xx, cs5530, cs5535, pdc202xx_new, sc1200, pmac
  and via82cxxx host drivers.

* Add IDE_HFLAG_NO_SET_MODE host flag to indicate the need to completely
  skip programming of host/device for the transfer mode ("smart" hosts).
  Set it in it821x host driver and check it in ide_tune_dma().

* Add ide_set_pio_mode()/ide_set_dma_mode() helpers and convert all
  direct ->set_pio_mode/->speedproc users to use these helpers.

* Move ide_config_drive_speed() calls from ->set_pio_mode/->speedproc
  methods to callers.

* Rename ->speedproc method to ->set_dma_mode, make it void and update
  all implementations accordingly.

* Update ide_set_xfer_rate() comments.

* Unexport ide_config_drive_speed().

v2:
* Fix issues noticed by Sergei:
  - export ide_set_dma_mode() instead of moving ->set_pio_mode abuse wrt
    to setting DMA modes from sc1200_set_pio_mode() to do_special()
  - check IDE_HFLAG_NO_SET_MODE in ide_tune_dma()
  - check for (hwif->set_pio_mode) == NULL in ide_set_pio_mode()
  - check for (hwif->set_dma_mode) == NULL in ide_set_dma_mode()
  - return -1 from ide_set_{pio,dma}_mode() if ->set_{pio,dma}_mode == NULL
  - don't set ->set_{pio,dma}_mode on it821x in "smart" mode
  - fix build problem in pmac.c
  - minor fixes in au1xxx-ide.c/cs5530.c/siimage.c
  - improve patch description

Changes in behavior caused by this patch:
- HDIO_SET_PIO_MODE ioctl would now return -ENOSYS for attempts to change
  PIO mode if it821x controller is in "smart" mode
- removal of two debugging printk-s (from cs5530.c and sc1200.c)
- transfer modes 0x00-0x07 passed from user space may be programmed twice on
  the device (not really an issue since 0x00 is not supported correctly by
  any host driver ATM, 0x01 is not supported at all and 0x02-0x07 are invalid)
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      88b2b32b
    • B
      ide-pmac: remove pmac_ide_do_setfeature() (take 2) · aedea591
      由 Bartlomiej Zolnierkiewicz 提交于 
      Use ide_config_drive_speed() instead of pmac_ide_do_setfeature() and remove
the latter, also  ide-iops.c::__ide_wait_stat() could be static again.

Since for IDE PMAC host driver IDE_CONTROL_REG is always true, device's
->quirk_list is always zero and ->ide_dma_host_{on,off} are nops than
the only changes in behavior are:

* if PIO mode is set then ->dma_off_queitly is called to disable DMA

* if setting transfer mode fails ide_dump_status() is called to dump status

v2:
* IDE PMAC controllers allow separate PIO and DMA timings and PPC userland
  depends on this fact, and calls "hdparm -p" without calling "hdparm -d".

  Therefore to compensate for DMA being disabled by ide_config_drive_speed()
  for PIO modes:

  - add IDE_HFLAG_SET_PIO_MODE_KEEP_DMA flag and set it in PMAC host driver

  - add handling of the new flag to ide-io.c::do_special()

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      aedea591
    • B
      ide-pmac: use __ide_wait_stat() · ddf15102
      由 Bartlomiej Zolnierkiewicz 提交于 
      * Use __ide_wait_stat() instead of wait_for_ready() in pmac_ide_do_setfeature().

While at it do following changes to match __ide_wait_stat() call in
ide_config_drive_speed():

* Wait WAIT_CMD time (20 sec) instead of 2 sec for device to clear BUSY_STAT.

* Check DRQ_STAT bit (shouldn't be set for good device status).

Also remove no longer needed wait_for_ready() from ide-iops.c.
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      ddf15102
    • B
      ide: add __ide_wait_stat() helper · 74af21cf
      由 Bartlomiej Zolnierkiewicz 提交于 
      * Split off checking of the status register from ide_wait_stat() to
  __ide_wait_stat() helper.

* Use the new helper in ide_config_drive_speed().  The only change in the
  functionality is that the function now fails if after 20 sec (WAIT_CMD)
  device is still busy (BUSY_STAT bit is set) while previously instead of
  failing the function continued with checking for the correct device status
  (which would give the device additional 10 usec to clear BUSY_STAT bit).

* Remove stale comment for ide_config_drive_speed().

* Remove duplicate comment for ide_wait_stat() from <linux/ide.h>.

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      74af21cf
  25. 12 10月, 2007 1 次提交
    • B
      ide: add ide_set{_max}_pio() (take 4) · 26bcb879
      由 Bartlomiej Zolnierkiewicz 提交于 
      * Add IDE_HFLAG_ABUSE_{PREFETCH,FAST_DEVSEL,DMA_MODES} flags
  and set them in ht6560, cmd640, cmd64x and sc1200 host drivers.

* Add set_pio_mode_abuse() for checking if host driver has a non-standard
  ->tuneproc() implementation and use it in do_special().

* Add ide_set_pio() for setting PIO mode (it uses hwif->pio_mask to find
  the maximum PIO mode supported by the host), also add ide_set_max_pio()
  wrapper for ide_set_pio() to use for auto-tuning.  Convert users of
  ->tuneproc to use ide_set{_max}_pio() where possible.  This leaves only
  do_special(), set_using_pio(), ide_hwif_restore() and ide_set_pio() as
  a direct users of ->tuneproc.

* Remove no longer needed ide_get_best_pio_mode() calls and printk-s
  reporting PIO mode selected from ->tuneproc implementations.

* Rename ->tuneproc hook to ->set_pio_mode and make 'pio' argument const.

* Remove stale comment from ide_config_drive_speed().

v2:
* Fix "ata_" prefix (Noticed by Jeff).

v3:
* Minor cleanups/fixups per Sergei's suggestions.

v4:
* Fix compile problem in drivers/ide/pci/cmd640.c
  (Noticed by Andrew Morton).

* Improve some ->set_pio_mode comments.
Reviewed-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      26bcb879
  27. 12 9月, 2007 1 次提交
  29. 21 8月, 2007 2 次提交
    • B
      ide-disk: workaround for buggy HPA support on ST340823A (take 3) · b0244a00
      由 Bartlomiej Zolnierkiewicz 提交于 
      This disk reports total number of sectors instead of maximum sector address
in response to READ_NATIVE_MAX_ADDRESS command and also happily accepts
SET_MAX_ADDRESS command with the bogus value.  This results in +1 sector
capacity being used and errors on attempts to use the last sector.

...
hdd: Host Protected Area detected.
        current capacity is 78165360 sectors (40020 MB)
        native  capacity is 78165361 sectors (40020 MB)
hdd: Host Protected Area disabled.
...
hdd: reading: block=78165360, sectors=1, buffer=0xc1e63000
hdd: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdd: dma_intr: error=0x10 { SectorIdNotFound }, LBAsect=78165360, sector=78165360
...

Add hpa_list[] table and workaround the issue in idedisk_check_hpa().

v2:
* Add missing export and improve patch description a bit.

v3:
* Add list termination.  (From Mikko)

Fixes kernel bugzilla bug #8816.

Thanks to Mikko for investigating the issue and helping with this patch.

Cc: Mikko Rapeli <mikko.rapeli@iki.fi>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      b0244a00
    • B
      ide: ide_config_drive_speed() bugfixes · adcd33d4
      由 Bartlomiej Zolnierkiewicz 提交于 
      * Use ->OUTBSYNC instead of ->OUTB when writing command register
  (needed for scc_pata and pmac host drivers).

* Don't check DRDY bit of the status register on ATAPI devices
  (ATAPI devices are free to ignore DRDY bit).

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Cc: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      adcd33d4