In preparation for 64-bit stats interface, the following cleanups help
streamline the code:
1) made some more rx/tx stats stored by driver 64 bit
2) made some HW stas (err/drop counters) stored in be_drv_stats 32 bit to
   keep the code simple as BE provides 32-bit counters only.
3) removed duplication of netdev stats in ethtool
4) removed some un-necessary stats and fixed some names
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On a recent compile, I got this warning:

  CC [M]  drivers/net/pcmcia/smc91c92_cs.o
drivers/net/pcmcia/smc91c92_cs.c: In function ‘smc91c92_probe’:
drivers/net/pcmcia/smc91c92_cs.c:812:12: warning: ‘j’ may be used uninitialized in this function

However, "j" is only used in a branch which has the same condition as
a previous branch, where j is set, e.g.

	int j;

	if (CONDITION)
	    j = VALUE

	...

	if (CONDITION)
	   printk(j)

Still, avoid this warning, as it is easy to circumvent.
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>

Without CONFIG_HERMES_PRISM, only match cards that have "Version 01.01"
as the third product ID.  Those have Agere firmware.

With CONFIG_HERMES_PRISM, match all 0x0156:0x0002 cards.
Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>

Cards with numeric ID 0x0156:0x0002 and third ID "Version 01.02" can be
assumed to have Intersil firmware.  Cards with Agere firmware use
"Version 01.01".
Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>

Only Sparc and PPC actually have the asm/prom.h include and as such they
can't be moved outside of the ifdefs.
Reported-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The D-Link DGE-530T rev C1 is a re-badged Realtek 8169 named DLG10028C,
unlike the previous revisions which were skge based.  It is probably
the same as the discontinued DGE-528T (0x4300) other than the PCI ID.

The PCI ID is 0x1186:0x4302.

Adding it to r8169.c where 0x1186:0x4300 is already found makes the card
be detected and work.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=38862Signed-off-by: NLen Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Addresses https://bugzilla.kernel.org/show_bug.cgi?id=34552Signed-off-by: NKlement Fish <klement2@azet.sk>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The A0 revision of this chip is the only device that requires these
features to be disabled.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 5719 has bug where RDMAs larger than 4k can cause problems.  This
patch works around the problem by dividing larger DMA requests into
something the hardware can handle.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As the driver breaks large skb fragments into smaller submissions to the
hardware, there is a new danger that BDs might get exhausted before all
fragments have been mapped.  This patch adds code to make sure tx BDs
aren't oversubscribed and flag the condition if it happens.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch consolidates all code that populates tx BDs into a single
routine.  Setting tx BDs needs to be more carefully controlled to see if
workarounds need to be applied.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The following patches are going to break skb fragments into smaller
sizes.  This patch attempts to make the change easier to digest by only
addressing the skb teardown portion.

The patch modifies the driver to skip over any BDs that have a flag set
that indicates the BD isn't the beginning of an skb fragment.  Such BDs
were a result of segmentation and do not need a pci_unmap_page() call.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the following patches, unmapping skb fragments will get just as
complicated as mapping them.  This patch generalizes
tg3_skb_error_unmap() and makes it the one-stop-shop for skb unmapping.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The first fragment of an skb should always be greater than 8 bytes.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the following patches, the process the driver will use to assign skb
fragments to transmit BDs will get more complicated.  To prepare for
that new code, this patch seeks to simplify how transmit BDs are
populated.  It does this by separating the code that assigns the BD
members from the logic that controls how the fields are set.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The following patches will require the use of an additional flag in the
ring_info structure.  The use of this flag is tx path specific, so this
patch defines a specialized ring_info structure.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The AX88772B uses only 11 bits of the header for the actual size. The other bits
are used for something else. This causes dmesg full of messages:

	asix_rx_fixup() Bad Header Length

This patch trims the check to only 11 bits. I believe on older chips, the
remaining 5 top bits are unused.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Try to send to correct address this time!

----------  Forwarded Message  ----------

Subject: [PATCH] Fix cdc-phonet build
Date: Saturday 23 Jul 2011
From: Chris Clayton <chris2553@googlemail.com>
To: linux-net@vger.kernel.org

cdc-phonet does not presently build on linux-3.0 because there is no entry for it in
drivers/net/Makefile. This patch adds that entry.
Signed-off-by: NChris Clayton <chris2553@googlemail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On Tue, Jul 26, 2011 at 05:40:27PM -0700, Joe Perches wrote:
> On Tue, 2011-07-26 at 17:37 -0700, Jay Vosburgh wrote:
> > Joe Perches <joe@perches.com> wrote:
> > >I'd prefer you don't separate the format string
> > >into multiple pieces.
> > Why not?  To me, it looks easier to read split into sections
> > that don't wrap lines.
>
> Harder to grep for a dmesg and the
> defect rate of these split formats is
> typically higher than single strings
> because of bad spacing between string
> segments.
>

I noticed that you took some time back in late 2009 to 'consolidate' the
split format-strings present in the bonding driver at the time and I've
decided I'm fine to leave them the way they are.  The main point of my
patch was to change the output and I would like to get that included.
Here is my updated patch...

Subject: [PATCH net-next-2.6 v2] bonding: reduce noise during init

Many are using sysfs to configure bonding rather than module options, so
there is no need for bonding to throw this warning in normal cases.

Keep the message around when debugging is enabled as it might be useful
for someone desperate enough to enable debugging, but eliminate it
otherwise.
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a bond contains a device where one name is the subset of another
(eth1 and eth10, for example), one cannot properly set the primary
device or the currently active device.

This was reported and based on work by Takuma Umeya.  I also verified
the problem and tested that this fix resolves it.

V2: A few did not like the the current code or my changes, so I
refactored bonding_store_primary and bonding_store_active_slave to be a
bit cleaner, dropped the use of strnicmp since we did not really need
the comparison to be case insensitive, and formatted the input string
from sysfs so a comparison to IFNAMSIZ could be used.

I also discovered an error in bonding_store_active_slave that would
modify bond->primary_slave rather than bond->curr_active_slave before
forcing the bonding driver to choose a new active slave.

V3: Actually sending the proper patch....
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Reported-by: NTakuma Umeya <tumeya@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After the last patch, We are left in a state in which only drivers calling
ether_setup have IFF_TX_SKB_SHARING set (we assume that drivers touching real
hardware call ether_setup for their net_devices and don't hold any state in
their skbs.  There are a handful of drivers that violate this assumption of
course, and need to be fixed up.  This patch identifies those drivers, and marks
them as not being able to support the safe transmission of skbs by clearning the
IFF_TX_SKB_SHARING flag in priv_flags
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
CC: Karsten Keil <isdn@linux-pingi.de>
CC: "David S. Miller" <davem@davemloft.net>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Patrick McHardy <kaber@trash.net>
CC: Krzysztof Halasa <khc@pm.waw.pl>
CC: "John W. Linville" <linville@tuxdriver.com>
CC: Greg Kroah-Hartman <gregkh@suse.de>
CC: Marcel Holtmann <marcel@holtmann.org>
CC: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For some reason, when rxaccel is disabled, NV_RX3_VLAN_TAG_PRESENT is
still set and some pseudorandom vids appear. So check for
NETIF_F_HW_VLAN_RX as well. Also set correctly hw_features and set vlan
mode on probe.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 87c288c6 "gianfar: do vlan cleanup" has two issues:
# permutation of rx and tx flags
# enabling vlan tag insertion by default (this leads to unusable connections on some configurations)

If VLAN insertion is requested (via ethtool) it will be set at an other point ...
Signed-off-by: NSebastian Poehn <sebastian.poehn@belden.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It adds device tree probe support for fec driver.
Signed-off-by: NJason Liu <jason.hui@linaro.org>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NDavid S. Miller <davem@davemloft.net>

The patch extends 'enum phy_interface_t' and of_get_phy_mode a little
bit with PHY_INTERFACE_MODE_NA and PHY_INTERFACE_MODE_SMII added,
and then converts ibm_newemac net driver to use of_get_phy_mode
getting phy mode from device tree.

It also resolves the namespace conflict on phy_read/write between
common mdiobus interface and ibm_newemac private one.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NDavid Miller <davem@davemloft.net>

On the recent i.mx (mx25/50/53), there is a gasket inside fec
controller which needs to be enabled no matter phy works in MII
or RMII mode.

The current code enables the gasket only when phy interface is RMII.
It's broken when the driver works with a MII phy.  The patch uses
platform_device_id to distinguish the SoCs that have the gasket and
enables it on these SoCs for both MII and RMII mode.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Reported-by: NTroy Kisky <troy.kisky@boundarydevices.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: NDavid S. Miller <davem@davemloft.net>

This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: NArun Sharma <asharma@fb.com>
Reviewed-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

wldev is freed in b43_one_core_detach() and should not be accessed after
that call.  Keep wldev->dev in a local variable.
Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We've fixed the last issue with BCMA support which caused memory
corruption on loading and unloading b43. Support for BCMA in b43 was
tested with 14e4:4353, 14e4:4357, 14e4:4727 and 14e4:4331. First two
cards (BCM43224 and BCM43225) are supported.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fixes bug described in:
https://bugzilla.kernel.org/show_bug.cgi?id=39172Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Take Eric's patch one step further.
Use netdev_skb_ip_align to do setup the receive skb.
Compile tested only.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NShmulik Ravid <shmulikr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch includes:
 - Counting statistics ramrods as EQ ramrods the way they should be. This
   accounting is meant to prevent MC asserts in case of software bugs.
 - Fixes in debug facilities which were added while working on one of such
   bugs.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Also fixes minor formatting in that function.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As a result of DCBX negotiation some priorities maybe untouched and still
unmapped to any COS; instead of sending them to COS0 we assign them
to the same COS as L2 traffic - to avoid collisions with storage class of
service.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove duplicated #include('s) in
  drivers/net/via-velocity.c
Signed-off-by: NHuang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>