Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 15 9月, 2012 3 次提交
  3. 14 9月, 2012 4 次提交
  5. 20 7月, 2012 3 次提交
  7. 17 5月, 2012 7 次提交
  9. 27 3月, 2012 4 次提交
  11. 19 2月, 2012 1 次提交
  13. 15 12月, 2011 2 次提交
  15. 01 11月, 2011 1 次提交
  17. 17 10月, 2011 2 次提交
    • J
      [SCSI] lpfc 8.3.27: T10 additions for SLI4 · f9bb2da1
      由 James Smart 提交于 
      Added T10 DIFF error injection code.
Added T10 DIFF structure definitions for SLI4 devices.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
      f9bb2da1
    • J
      [SCSI] lpfc 8.3.27: Miscellanous logic and interface fixes · 73d91e50
      由 James Smart 提交于 
      Miscellanous logic and interface fixes

- Fix lpfc_init_vfi_cmpl to check the interface type for interface type 0
  before parsing the results.
- Cast uint32_t values that are multiplied to uint64_t before the
  multiplication.
- Instead of "break" statement when PCI read returned error, use the goto
  statement to the end of the routine after setting return value
- moved the msleep(10) to the beginning of the wait loop for checking the
  SLIPort_Status register
- Added the code to follow the existing wait for SLIPort_Status register RDY,
  ERR, and RN bits to be set by the port before proceeding to perform PCI
  function reset.
- Do not override ulpCt_h and ulpCt_l for SLI 4 ports.
- For vport delete, call lpfc_nlp_put when the vport's vpi state is not
  marked with VPI_REGISTERED.
- Added missed fields into the driver's Controller Attributes Structure
- Changed ringing EQ/CQ/RQ doorbell register to be dependent on the size
  of the queue.
- Return -EACCES in issue_reset if cfg_enable_hba_reset is zero.
- Added new logging flag LOG_FCP_UNDER 0x00040000 to qualify underrun logging.
- Add a check in the fabric name display routine to display 0 if the port
  state is <= FLOGI.
- Add a check to the switch statement in lpfc_decode_firmware_rev to check
  for an 'X'.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
      73d91e50
  19. 29 8月, 2011 1 次提交
  21. 27 7月, 2011 1 次提交
  23. 27 5月, 2011 2 次提交
    • J
      [SCSI] lpfc 8.3.24: Add resource extent support · 6d368e53
      由 James Smart 提交于 
      This patch adds support for hardware that returns resource ids via
extents rather than contiguous ranges.

[jejb: checkpatch.pl fixes]
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>
      6d368e53
    • J
      [SCSI] lpfc 8.3.24: Miscellaneous Fixes and Corrections · 0558056c
      由 James Smart 提交于 
      Miscellaneous Fixes and Corrections
- Remove the memset in the lpfc_sli4_remove_rpi_hdrs call.
- Correct swapping of SGE word 2 relative to offset value
- Reorganize CQ and EQ usage to comply with SLI4 Specification.
- Expand the driver to check the rn bit. Only detect an error if the error bit
  is set and the RN bit is NOT set.
- If mailbox completion code is not success AND the mailbox status is success,
  then and only then will the driver overwrite the mailbox status.
- When driver initializing device, if the device is on a PCIe bus, set
  PCI's "needs fundamental reset" bit so that EEH uses fundamental reset
  instead of hot reset for recovery.
- Prevent driver from using new WWN when changed in firmware (until driver
  reload)
- When HBA reports maximum SGE size > 0xffffffff (infinite), override
  with 0x80000000.
- Fixed potential missed SLI4 device initialization failure conditions.
- Added 100ms delay before driver action following IF_TYPE_2 function reset.
- Reverted patch to UNREG/REG on PLOGI to mapped/unmapped node.
- Add a check for the CVL received flag in the fcf inuse routine to avoid
  unregistering the fcf if Devloss fires before Delay discover timer fires.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>
      0558056c
  25. 01 5月, 2011 1 次提交
  27. 31 3月, 2011 1 次提交
  29. 24 3月, 2011 2 次提交
  31. 01 3月, 2011 2 次提交
  33. 19 2月, 2011 3 次提交