- 16 5月, 2015 2 次提交
-
-
由 Ariel D'Alessandro 提交于
Add basic support for Hitex LPC4350 Evaluation Board. Board features a LPC4350 Soc, 8 MB SDRAM, 8 MB SPI Flash, USB and Ethernet. More information can be found on: http://www.hitex.com/index.php?id=3212Signed-off-by: NAriel D'Alessandro <ariel.dalessandro@gmail.com> Signed-off-by: NJoachim Eastwood <manabian@gmail.com> Signed-off-by: NArnd Bergmann <arnd@arndb.de>
-
由 Joachim Eastwood 提交于
Adds basic support for Embedded Artists' LPC4357 Developer's Kit. Board features a LPC4357 Soc, 32 MB SDRAM, 128 MB NAND Flash, 16 MB SPI Flash, USB and Ethernet. More information can be found on: http://www.embeddedartists.com/products/kits/lpc4357_kit.phpSigned-off-by: NJoachim Eastwood <manabian@gmail.com> Signed-off-by: NArnd Bergmann <arnd@arndb.de>
-
- 14 5月, 2015 4 次提交
-
-
由 Rafał Miłecki 提交于
Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
-
由 Rafał Miłecki 提交于
Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
-
由 Rafał Miłecki 提交于
Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
-
由 Felix Fietkau 提交于
Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
-
- 12 5月, 2015 2 次提交
-
-
由 Masahiro Yamada 提交于
Initial device trees for UniPhier SoCs: PH1-sLD3, PH1-LD4, PH1-Pro4, and PH1-sLD8. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: NArnd Bergmann <arnd@arndb.de>
-
由 Dinh Nguyen 提交于
Rename the socfpga_arria10_socdk board file to socfpga_arria10_socdk_sdmmc as Arria 10 devkit cannot support SDMMC and QSPI at the same time. Thus we will need to have 2 separate board files, one for SDMMC and one for QSPI. We also add a new base board dtsi file, socfpga_arria10_socdk.dtsi so that we use common peripherals for each flavor of the devkits. Add the sdmmc node to the socfpga_arria10_socdk_sdmmc.dts board file. Signed-off-by: NDinh Nguyen <dinguyen@opensource.altera.com>
-
- 11 5月, 2015 4 次提交
-
-
由 Sebastian Hesselbarth 提交于
With reworked device tree files for Compulab CM-A510 SoM and SBC-A510 base board, now add the correspoding board file to Makefile again. Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
-
由 Sebastian Hesselbarth 提交于
Prior reworking Dove based Compulab CM-A510 device tree, remove it from the compiled device tree files. Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
-
由 Gaël PORTAY 提交于
Add DT file for Kizbox 2 board. This board is based on Atmel's SAMA5D31 Cortex-A5 SoC. Signed-off-by: NGaël PORTAY <g.portay@overkiz.com> Acked-by: NBoris Brezillon <boris.brezillon@free-electrons.com> Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
-
由 Gaël PORTAY 提交于
Add DT file for Kizbox mini board. This board is based on Atmel's AT91SAM9G25 SoC. Signed-off-by: NGaël PORTAY <g.portay@overkiz.com> Acked-by: NBoris Brezillon <boris.brezillon@free-electrons.com> Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
-
- 30 4月, 2015 2 次提交
-
-
由 Gaël PORTAY 提交于
Rename to match AT91 naming convention. Signed-off-by: NGaël PORTAY <g.portay@overkiz.com> Acked-by: NBoris Brezillon <boris.brezillon@free-electrons.com> Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
-
由 Marcus Cooper 提交于
The MK808C is an A20 based android stick, with 1G RAM, 8G NAND flash, a RTL8723au wifi + bt combo chip, a USB host ports using USB-A receptacles, a mini USB-B receptacle for USB OTG, mini HDMI and a TRS connector for AV. This patch adds basic support for the device, more information can be found here (http://linux-sunxi.org/MK808C). Signed-off-by: NMarcus Cooper <codekipper@gmail.com> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
- 27 4月, 2015 10 次提交
-
-
由 Hans de Goede 提交于
The Jesurun Q5 has a black plastic casing with the approximate dimensions of 100mm x 100mm x 24mm with rounded edges. In terms of hardware it features an Allwinner A10 SoC with 1GB RAM and 8GB of NAND flash. The external connectors are: 2x USB-A female supporting USB2.0, 3.5mm female jack for audio, HDMI female, SPDIF, RJ45 LAN and Power. In addition the device has 1x red LED (hard wired to power) and an programmable green led. On the board there is also an unpopulated IR receiver and the UART. The devices is equipped with an AXP209 PMU. For more details see: http://linux-sunxi.org/Jesurun_Q5Signed-off-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Hans de Goede 提交于
The Orangepi mini is a development board using the Allwinner A20 SoC, with 1G RAM, 2 microsd slots (use the top side one for booting), HDMI, 1Gbit ethernet, USB wifi, Micro USB (otg), sata, 4 USB A ports, ir receiver and a headphones jack. Also see: http://linux-sunxi.org/Xunlong_Orange_Pi_Mini http://www.orangepi.org/Signed-off-by: NHans de Goede <hdegoede@redhat.com> [maxime: Added /chosen/stdout-path] Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Hans de Goede 提交于
The Orangepi is a development board using the Allwinner A20 SoC, with 1G RAM, microsd slot, HDMI, 1Gbit ethernet, USB wifi, Micro USB (otg), sata, 4 USB A ports, ir receiver and a headphones jack. Also see: http://linux-sunxi.org/Xunlong_Orange_Pi http://www.orangepi.org/Signed-off-by: NHans de Goede <hdegoede@redhat.com> [maxime: Added /chosen/stdout-path] Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Tyler Baker 提交于
Add a Cubietech Cubieboard4 device tree and instruct make to build it. This device tree has been derived from the sun9i-a80-optimus.dts as they are very similar in design[1]. Notably, I2C3 is not used on Cubieboard4 and the LED/PWM definitions will need to be updated in the future. [1] http://dl.cubieboard.org/model/cc-a80/Hardware/CC-A80-HW-V1.1.pdfSigned-off-by: NTyler Baker <tyler.baker@linaro.org> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Aleksei Mamlin 提交于
This patch add support for Wexler TAB7200 tablet. The Wexler TAB7200 is a A20 based tablet with 7 inch display(800x480), capacitive touchscreen(5 fingers), 1G RAM, 4G NAND, micro SD card slot, mini HDMI port, 3.5mm audio plug, 1 USB OTG port and 1 USB 2.0 port. Signed-off-by: NAleksei Mamlin <mamlinav@gmail.com> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Hans de Goede 提交于
The UTOO P66 is a 6" A13 tablet / lcd ereader. It features a 6" 480x800 ips lcd screen, 512MB RAM & 4GB emmc. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Hans de Goede 提交于
The auxtek-t004: http://www.fasttech.com/products/1110/10004200/1318603-auxtek-t004-allwinner-a10s-single-core-android-ics Is an Allwinner A10s based hdmi tv stick with with 512M RAM, 4G nand flash, toc9002 (bcm43362) sdio wifi, 1 USB host ports using an USB-A receptacle and a 2 micro-usb receptacles, one for power and one for USB OTG. The sdio wifi appears to not have an oob irq hooked up, so we rely on sdio-irq support for it. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Marcus Cooper 提交于
The Mele I7 is a Allwinner A31 based Android TV box, with 1G RAM, 8GB NAND flash, a RTL8188etv wifi chip, 3 USB Host ports using USB-A receptacles, a micro USB-B receptacle for USB OTG, HDMI out, a TRS connector for A/V, SPDIF and IrDA. This patch adds basic support for the device, more information can be found here (http://linux-sunxi.org/Mele_I7). Signed-off-by: NMarcus Cooper <codekipper@gmail.com> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Adam Sampson 提交于
Add support for the LinkSprite pcDuino 3 Nano board. This is a low-cost Allwinner A20 board with Arduino-style GPIO headers; it features 1G RAM, 4G NAND flash, 1 micro-SD, 2 USB sockets, 1 micro USB socket for OTG and another for power in, HDMI, SATA, 5V power for SATA devices, gigabit Ethernet, an IR receiver, 3.5mm audio out and a MIPI camera connector. For more details, see: http://linux-sunxi.org/LinkSprite_pcDuino3_Nano Changes in v3: - rename LEDs to pcduino3-nano:green:usr[12] - remove optional features on Arduino headers (i2c2, spi0, uart2) Signed-off-by: NAdam Sampson <ats@offog.org> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Priit Laes 提交于
Gemei G9 is an A10 based tablet, with 1G RAM, 16G NAND, 1024x768 IPS LCD display, stereo speakers, 1.3MP front camera and 5 MP rear camera, 8000mAh battery, GT901 2+1 touchscreen, Bosch BMA250 accelerometer and RTL8188CUS USB wifi. It also has MicroSD slot, miniHDMI, 1 x MicroUSB OTG port and 1 x MicroUSB host port and 3.5mm headphone jack. Changes since v2: * Fix syntax error (brown paper bag release) Changes since v1: * Added sun4i-lradc keymap * Added TODO note about missing IRQ pins for bma250 * Fixed formatting issues and removed external URLs Signed-off-by: NPriit Laes <plaes@plaes.org> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
- 02 4月, 2015 1 次提交
-
-
由 Olof Johansson 提交于
File uses dash in the filename, not underscore. Reported-by: NRussell King <linux@arm.linux.org.uk> Signed-off-by: NOlof Johansson <olof@lixom.net>
-
- 30 3月, 2015 3 次提交
-
-
由 Otavio Salvador 提交于
The WaRP Board is a Wearable Reference Plaform. The board features: - Freescale i.MX6 SoloLite processor with 512MB of RAM - Freescale FXOS8700CQ 6-axis Xtrinsic sensor - Freescale Kinetis KL16 MCU - Freescale Xtrinsic MMA955xL intelligent motion sensing platform The board implements a hybrid architecture to address the evolving needs of the wearables market. The platform consists of a main board and an example daughtercard with the ability to add additional daughtercards for different usage models. For more information about the project, visit: http://www.warpboard.org/Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Peter Chen 提交于
Since imx6sx-sdb reva board is experimental and will not be used formally (eg, no software release based on it), we set revb board as the formal imx6sx-sdb board. The imx6sx-sdb uses pfuse200 as pmic which has only one power supply for both VDDARM_IN and VDDSOC_IN, so VDDARM_IN and VDDSOC_IN have to use the same (higher one in the same frequency) one as its power supply, that's the reason we override the OPP setting in board dts file. Signed-off-by: NPeter Chen <peter.chen@freescale.com> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Peter Chen 提交于
The imx6sx sdb board has two revisions, the current mainline one is reva which is experimental and mainly for internal use. In this commit, we rename imx6sx-sdb.dts to imx6sx-sdb.dtsi, and move the reva dedicated contents to imx6sx-sdb-reva.dts. Signed-off-by: NPeter Chen <peter.chen@freescale.com> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
- 24 3月, 2015 1 次提交
-
-
由 Tomeu Vizoso 提交于
It's commercial name is HP Chromebook 14 and is substantially similar to the Acer Chromebook 13 (nyan-big). Signed-off-by: NTomeu Vizoso <tomeu.vizoso@collabora.com> Acked-by: NStephen Warren <swarren@nvidia.com> Reviewed-by: NAlexandre Courbot <acourbot@nvidia.com> Signed-off-by: NThierry Reding <treding@nvidia.com>
-
- 17 3月, 2015 3 次提交
-
-
由 H. Nikolaus Schaller 提交于
Added Pandora 1 GHz model which is based on Classic/Rebirth with following changes: - upgraded cpu to dm3730 runs on 1GHz - 512 MiB DDR-333 SDRAM @ 200 MHz Signed-off-by: NH. Nikolaus Schaller <hns@goldelico.com> Tested-by: NGrazvydas Ignotas <notasas@gmail.com> Reviewed-by: NGrazvydas Ignotas <notasas@gmail.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 H. Nikolaus Schaller 提交于
Added Pandora Rebirth model which is based on Pandora Classic with 512 MiB DDR-333 SDRAM memory. Signed-off-by: NH. Nikolaus Schaller <hns@goldelico.com> Tested-by: NGrazvydas Ignotas <notasas@gmail.com> Reviewed-by: NGrazvydas Ignotas <notasas@gmail.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Rostislav Lisovy 提交于
Chiliboard uses ChiliSOM as its base. Hardware specification: * ChiliSOM (am335x, PMIC, DRAM, NAND) * Ethernet PHY (id 0) * USB host (usb1) * microSD slot * 2x GPIO LED Signed-off-by: NRostislav Lisovy <lisovy@jablotron.cz> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
- 16 3月, 2015 1 次提交
-
-
由 Tsahee Zidenberg 提交于
This patch introduces devicetree for the Alpine platform, and for a development board based on the same platform. Signed-off-by: NBarak Wasserstrom <barak@annapurnalabs.com> Signed-off-by: NTsahee Zidenberg <tsahee@annapurnalabs.com> Acked-by: NArnd Bergmann <arnd@arndb.de> Signed-off-by: NArnd Bergmann <arnd@arndb.de>
-
- 12 3月, 2015 1 次提交
-
-
由 Simon Guinot 提交于
This patch adds the DT description for the LaCie "2Big NAS" (nas2big). This NAS is an hardware upgrade of the 2Big Network v2. Chipset and device list: - CPU Marvell 88F6282 1600Mhz - SDRAM memory, 256MB DDR3 (2x128MB x8) 533Mhz - 1 Ethernet Gigabit port (PHY Marvell 88E1518) - Flash memory, NAND 256MB TSOP48 - I2C EEPROM, 512 bytes (AT24 type) - PCIe SATA controller JMicron JMB360 (eSATA) - I2C fan controller GMT G762 (with a separate alarm GPIO) - 1 USB2 host port - 1 push button - 1 power switch - 2 SATA LEDs (bi-color, blue and red) - 1 power LED (bi-color, blue and red) - CPLD for LEDs and start-up management (Altera Max EMP3064) Signed-off-by: NSimon Guinot <simon.guinot@sequanux.org> Acked-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
-
- 07 3月, 2015 1 次提交
-
-
由 Rafał Miłecki 提交于
Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Reported-by: NIan Kent <raven@themaw.net> Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
-
- 05 3月, 2015 1 次提交
-
-
由 Josh Wu 提交于
Add at91 sama5d4 xplained board support. Signed-off-by: NJosh Wu <josh.wu@atmel.com> Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
-
- 04 3月, 2015 1 次提交
-
-
由 Thomas Petazzoni 提交于
This commit adds the Device Tree files for the Armada 39x family of processors, as well as one Armada 398 Development Board. Like for other Marvell EBU families, a common armada-39x.dtsi contains the description of the common features of all Armada 39x SoCs, while armada-390.dtsi and armada-398.dtsi respectively describe the specificities of those SoCs. Finally, an armada-398-db.dts file is added to describe the Armada 398 Development Board itself. So far, the following features are supported: * SMP: dual Cortex-A9 * Basic ARM IPs: SCU, timer, GIC, L2 cache * Basic Marvell IPs: pin-muxing, clocks, system controller, MBus controller, MPIC interrupt controller, timer, CPU reset for SMP, PMSU. * I2C * SPI * SDHCI * XOR * NAND * UART * PCIe Additional features will be supported in the future. Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
-
- 03 3月, 2015 1 次提交
-
-
由 Jonathan Richardson 提交于
DT file to enable the Wireless Audio reference design based on the BCM58305. Reviewed-by: NRay Jui <rjui@broadcom.com> Reviewed-by: NScott Branden <sbranden@broadcom.com> Tested-by: NScott Branden <sbranden@broadcom.com> Signed-off-by: NJonathan Richardson <jonathar@broadcom.com> Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
-
- 02 3月, 2015 1 次提交
-
-
由 Beniamino Galvani 提交于
Add a DTS file for MINIX NEO-X8, a Meson8-based digital media player. Signed-off-by: NBeniamino Galvani <b.galvani@gmail.com> Signed-off-by: NCarlo Caione <carlo@endlessm.com>
-
- 01 3月, 2015 1 次提交
-
-
由 Ulrich Hecht 提交于
Adds config option and enables DTB building. Signed-off-by: NUlrich Hecht <ulrich.hecht+renesas@gmail.com> Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-