Since the 11n spec amendment was rolled into the
2012 version, "11n" no longer makes sense. Use
"HT" instead.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If the driver doesn't support 40 MHz channels, then
mac80211 erroneously sets number of RX chains to one
although the number of chains is independent of the
support for 40 MHz channels.

Fix this by checking the 40 MHz support only for the
code that sets the 40 MHz channel not the complete
HT code block.

This also means the HT20 channel type will always be
set in the changed code block so there's no need to
set it in case we override the AP due to invalid IEs
in the probe response/beacon.

The indentation is a bit quirky, but I'm rewriting
this code for VHT support so this will change again
very soon.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

While connected to a GO, parse the P2P NoA attribute
and pass the CT Window and opportunistic powersave
parameters to the driver.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When userspace asks to deauthenticate and we're just
authenticated (or still authenticating) send a deauth
frame instead of deleting the auth request.

On the other hand, if we've just disassociated and
therefore deleted all our state already, drop the
deauth request because we no longer have a channel
context to send it on.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Even before channel contexts/multi-channel, having a
single global TX power limit was already problematic,
in particular if two managed interfaces connected to
two APs with different power constraints. The channel
context introduction completely broke this though and
in fact I had disabled TX power configuration there
for drivers using channel contexts.

Change everything to track TX power per interface so
that different user settings and different channel
maxima are treated correctly. Also continue tracking
the global TX power though for compatibility with
applications that attempt to configure the wiphy's
TX power globally.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Remove a duplicate check in ieee80211_rx_mgmt_beacon,
there is no need to make again the same check for the
IEEE80211_HW_PS_NULLFUNC_STACK twice; the two ifs can
be consolidated.
Signed-off-by: NRami Rosen <ramirose@gmail.com>
[reword commit message & break long lines and also
 clean up variable]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There are a number of unused variables that gcc
pointed out (when building with W=1) as well as
some conditions that can never be true due to
the datatypes used: unsigned values can't be
less than zero. Remove this code.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Some changes to fix issues with HT40 APs in Korea
and follow-up changes to allow using HT40 even if
the local regulatory database disallows it caused
issues with iwlwifi (and could cause issues with
other devices); iwlwifi firmware would assert if
you tried to connect to an AP that has an invalid
configuration (e.g. using HT40- on channel 140.)

Fix this, while avoiding the "Korean AP" issue by
disabling HT40 and advertising HT20 to the AP
when connecting.

Cc: stable@vger.kernel.org [3.6]
Reported-by: NFlorian Reitmeir <florian@reitmeir.org>
Tested-by: NFlorian Reitmeir <florian@reitmeir.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Save the AP's VHT capabilities (in managed
mode) and make them available to the driver
in the station information.

Unlike HT capabilities, they aren't restricted
to the common capabilities, so drivers must be
aware of their own capabilities.
Signed-off-by: NMahesh Palivela <maheshp@posedge.com>
[fix endian conversion bug ...]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Rename struct ieee80211_vht_capabilities to ieee80211_vht_cap
and renamed its member vht_capabilities_info to vht_cap_info.
Signed-off-by: NMahesh Palivela <maheshp@posedge.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

SAE uses two rounds of Authentication frames and both rounds require
considerable calculation to be done. This commit extends the existing
station mode authentication request to allow more control for user
space programs to build the SAE fields and to run the authentication
step ones. Only the second round with authentication transaction
sequence 2 will result in moving to authenticated state.
Signed-off-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This is useful when debugging authentication process issues.
Signed-off-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Non-zero status code may be needed for Authentication frames, e.g.,
when using SAE.
Signed-off-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

On each channel that the device is operating on, it
may need to listen using one or more chains depending
on the SMPS settings of the interfaces using it. The
previous channel context changes completely removed
this ability (before, it was available as the SMPS
mode).

Add per-context tracking of the required static and
dynamic RX chains and notify the driver on changes.
To achieve this, track the chains and SMPS mode used
on each virtual interface and update the channel
context whenever this changes.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Instead of operating on a single channel only,
use the new channel context infrastructure in
all mac80211 code.

This enables drivers that want to use the new
channel context infrastructure to use multiple
channels, while nothing should change for all
the other drivers that don't support it.

Right now this disables both TX power settings
and spatial multiplexing powersave. Both need
to be re-enabled on a channel context basis.

Additionally, when channel contexts are used
drop the connection when channel switch is
received rather than trying to handle it. This
will have to be improved later.

[With fixes from Eliad and Emmanuel incorporated]
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Avoid situation when we are on associate state in mac80211 and
on disassociate state in cfg80211. This can results on crash
during modules unload (like showed on this thread:
http://marc.info/?t=134373976300001&r=1&w=2) and possibly other
problems.
Reported-by: NPedro Francisco <pedrogfrancisco@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When we disassociate, it's not really useful to
send delBA action frames since we're going to send
disassoc/deauth anyway, so change that.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Make the function acquire the necessary mutex itself
to simplify the callers.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Currently, mac80211 uses the power constraint IE, and reduces
the regulatory max TX power by it. This can cause issues if
the AP is advertising a large power constraint value matching
a high TX power in its country IE, for example in this case:

...
Country: US  Environment: Indoor/Outdoor
    ...
    Channels [157 - 157] @ 30 dBm
    ...
Power constraint: 13 dB
...

What happened here is that our local regulatory TX power is
15 dBm, and gets reduced by 13 dB so we end up with only
2 dBm effective TX power, which is way too low.

Instead, handle the country IE/power constraint IE combined
and restrict our TX power to the max of the regulatory power
and the maximum power advertised by the AP, in this case
17 dBm (= 30 dBm - 13 dB).

Also print a message when this happens to let the user know
and help us debug issues with it.
Reported-by: NCarl A. Cook <CACook@quantum-equities.com>
Tested-by: NCarl A. Cook <CACook@quantum-equities.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Move ieee80211_send_deauth_disassoc() to util.c to make it
available for the rest of the mac80211 code.
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>
[reword commit message]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The power constraint IE is always a single byte
so check the size when parsing instead of later.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Disconnect from the AP if channel switching in the
driver failed or if the new channel is unavailable.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

ifmgd->bssid wasn't cleared properly in some
auth/assoc failure cases, causing mac80211 and
the low-level driver to go out of sync.

Clear ifmgd->bssid on failure, and notify the driver.

Cc: stable@kernel.org # 3.4+
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In multi-channel scenarios, the channel that we will
transmit a probe request on isn't always the current
channel (which will be NULL anyway) but will instead
be the channel that the AP is on. Pass the channel
to the ieee80211_send_probe_req() function so it can
be used in the different scenarios. The scan code
continues to pass the current channel, of course.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's no need to declare the function in the
header file since it's only used in a single
place, so make it static.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The channel switch IE has a fixed size, so we can
discard it in parsing if it's not the right size
and use the right struct pointer.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The time until the channel switch is in TU,
not in milliseconds, so use TU_TO_EXP_TIME()
to correctly program the timer.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Clean up the CSA handling code by moving some
of it out of the if and using a C99 initializer
for the struct passed to the driver method.

While at it, also add a comment that we should
wait for a beacon after switching the channel.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's no need to copy the BSSID just to print
it, remove the unnecessary variable.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's a corner case that can happen when we
suspend with a timer running, then resume and
disconnect. If we connect again, suspend and
resume we might start timers that shouldn't be
running. Reset the timer flags to avoid this.

This affects both mesh and managed modes.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When associating anew, the old station MLME flags should
be cleared. The only exception is the 40 MHz disable
flag as it might have been set while the channel was set
in a previous authentication attempt so it needs to be
kept intact.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When sending probe requests, e.g. during software scanning,
these will go out on the *current* channel, so their IEs
need to be built from the current channel. At other times,
e.g. for beacons or probe request templates, the IEs will
be used on the *operating* channel and using the current
channel instead might result in errors.

Add the appropriate parameters to respect the difference.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Using hw.conf.channel is wrong as it could be the
temporary channel if any function like the beacon
get function is called while scanning or during
other temporary out-of-channel activities.

Use oper_channel instead.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's no need to set up the channel during auth
and again during assoc, just do it once. Currently
this doesn't result in any changes since calling
hw_config() with an unchanged channel will return
early, but with the channel context work this has
an impact on channel context assignment.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In ieee80211_prep_connection(), the station (if not NULL)
is the new station (representing the AP) that needs to be
added. Rename the variable to "new_sta" to clarify this.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If HT/VHT isn't supported by us we shouldn't print
a message that we disabled it, do that only if the
AP didn't support WMM and we therefore disable it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Currently, ps mode is indicated per device (rather than
per interface), which doesn't make a lot of sense.

Moreover, there are subtle bugs caused by the inability
to indicate ps change along with other changes
(e.g. when the AP deauth us, we'd like to indicate
CHANGED_PS | CHANGED_ASSOC, as changing PS before
notifying about disassociation will result in null-packets
being sent (if IEEE80211_HW_SUPPORTS_DYNAMIC_PS) while
the sta is already disconnected.)

Keep the current per-device notifications, and add
parallel per-vif notifications.

In order to keep it simple, the per-device ps and
the per-vif ps are orthogonal - the per-vif ps
configuration is determined only by the user
configuration (enable/disable) and the connection
state, and is not affected by other vifs state and
(temporary) dynamic_ps/offchannel operations
(unlike per-device ps).
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This doesn't make any sense since we are expected to be on
the medium or at least to Tx only when we are on the right
channel and the AP/GO can hear us.

Move the call to mgd_prepare_tx() for deauth to be only
done in case we're sending a deauth while not associated.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If the HW is monitoring connection loss (as advertised
by IEEE80211_HW_CONNECTION_MONITOR) but not filtering
beacons (IEEE80211_VIF_BEACON_FILTER) then mac80211 will
still start the beacon loss timer and if a few beacons
are lost, e.g. due to scanning, drop the connection.

If the hardware doesn't advertise connection monitoring,
then it won't drop the connection right away but probe
the AP, which is intended, but due to the logic in the
timer when connection monitoring is done it assumes the
connection was actually lost.

Fix this problem by not starting the timer when the HW
does connection monitoring.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Insert VHT IEs into association frames to allow
mac80211 to connect as a VHT client.
Signed-off-by: NMahesh Palivela <maheshp@posedge.com>
[clarify commit message]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>