Add support for a single-port X550 device.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch enables bulk free in Tx cleanup for ixgbevf and cleans up the
boolean logic in the polling routines for ixgbe and ixgbevf in the hopes of
avoiding any mix-ups similar to what occurred with i40e and i40evf.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it so that we can use the ethtool rx-vlan-filter flag to
toggle Rx VLAN filtering on and off.  This is basically just an extension
of the existing VLAN promisc work in that it just adds support for the
additional ethtool flag.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Added support to match on UDP fields in the transport layer.
Extended core logic to support multiple headers.

Verified with the following filters :

	handle 1: u32 divisor 1
	u32 ht 800: order 1 link 1: \
	offset at 0 mask 0f00 shift 6 plus 0 eat match ip protocol 6 ff
	u32 ht 1: order 2 \
	match tcp src 1024 ffff match tcp dst 23 ffff action drop
	handle 2: u32 divisor 1
	u32 ht 800: order 3 link 2: \
	offset at 0 mask 0f00 shift 6 plus 0 eat match ip protocol 17 ff
	u32 ht 2: order 4 \
	match udp src 1025 ffff match udp dst 24 ffff action drop
Signed-off-by: NAmritha Nambiar <amritha.nambiar@intel.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Acked-by: NSridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

It is possible on some HW that a system reset could occur when we are
holding the SWFW semaphore lock.  So next time the driver was loaded we
would see it incorrectly as locked. This patch will recover from that state
by: Attempting to acquire the semaphore and then regardless of whether or
not it was acquire we immediately release it. This will force us into
a known good state.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This commit adds a callback which allows to adjust the maximum transmit
bitrate the card can output. This makes it possible to get a smooth
traffic instead of the default burst-y behaviour when trying to output
e.g. a video stream.

Much of the logic needed to get a correct bcnrc_val was taken from the
ixgbe_set_vf_rate_limit() function.
Signed-off-by: NRostislav Pehlivanov <atomnuker@gmail.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for generic Tx checksums to the ixgbe driver.  It
turns out this is actually pretty easy after going over the datasheet as we
were doing a number of steps we didn't need to.

In order to perform a Tx checksum for an L4 header we need to fill in the
following fields in the Tx descriptor:
  MACLEN (maximum of 127), retrieved from:
		skb_network_offset()
  IPLEN  (maximum of 511), retrieved from:
		skb_checksum_start_offset() - skb_network_offset()
  TUCMD.L4T indicates offset and if checksum or crc32c, based on:
		skb->csum_offset

The added advantage to doing this is that we can support inner checksum
offloads for tunnels and MPLS while still being able to transparently
insert VLAN tags.

I also took the opportunity to clean-up many of the feature flag
configuration bits to make them a bit more consistent between drivers.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This commit converts commit c762dff2 ("ixgbe: Look up MAC address in
Open Firmware or IDPROM") to use eth_platform_get_mac_address()
added by commit c7f5d105 ("net: Add eth_platform_get_mac_address()
helper.")
Signed-off-by: NSowmini Varadhan <sowmini.varadhan@oracle.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The source for the ops structure contents are const, so make them
so. Copy them in place with structure assignments instead of memcpys.
Make the mbx_ops accessed by reference instead of making a copy of
the source structure. Update copyright date on the touched files.
Reported-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Acked-by: NJulia Lawall <julia.lawall@lip6.fr>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We were adding VLAN 0 twice each time we restored the VLAN configuration.
Instead of doing it twice we can just start working through the active
VLANs from ID 1 on and skip the double write.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

While doing the work on igb I realized there were a few cases where we were
still adding VLANs to the VLVF entries for the PF when they were not
needed.  This patch cleans that up so that the only time we add a PF entry
to the VLVF is either for VLAN 0 or if the PF has requested a VLAN that a VF
is already using.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove the incorrect check for mask in ixgbe_configure_clsu32 and
drop the 'mask' field that is not required in struct ixgbe_mat_field

Verified with the following filters:

 #tc qdisc add dev p4p1 ingress
 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
	handle 800:0:1 u32 ht 800: \
	match ip dst 10.0.0.1/8 match ip src 10.0.0.2/8 action drop
 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
	handle 800:0:2 u32 ht 800: \
	match ip dst 11.0.0.1/16 match ip src 11.0.0.2/16 action drop
 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
	handle 800:0:3 u32 ht 800: \
	match ip dst 12.0.0.1/24 match ip src 12.0.0.2/24 action drop
 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
	handle 800:0:4 u32 ht 800: \
	match ip dst 13.0.0.1/32 match ip src 13.0.0.2/32 action drop
Signed-off-by: NSridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Check for handle ids when adding/deleting hash nodes OR adding/deleting
filter entries and limit them to max number of links or header nodes
supported(IXGBE_MAX_LINK_HANDLE).

Start from bit 0 when setting hash table bit-map.(adapter->tables)
Signed-off-by: NSridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This function is only used in ixgbe_main.c
Resolves a "missing prototype" warning when building the driver with W=1
Reported-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Calling dev_close() causes IFF_UP to be cleared which will remove the
interfaces routes and some addresses. That's probably not what the user
intended when running the offline selftest. Besides this does not happen
if the interface is brought down before the test, so the current
behaviour is inconsistent.
Instead call the net_device_ops ndo_stop function directly and avoid
touching IFF_UP at all.
Signed-off-by: NStefan Assmann <sassmann@kpanic.de>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The ATR code was assuming that it would be able to use tcp_hdr for
every TCP frame that came through.  However this isn't the case as it
is possible for a frame to arrive that is TCP but sent through something
like a raw socket.  As a result the driver was setting up bad filters in
which tcp_hdr was really pointing to the network header so the data was
all invalid.

In order to correct this I have added a bit of parsing logic that will
determine the TCP header location based off of the network header and
either the offset in the case of the IPv4 header, or a walk through the
IPv6 extension headers until it encounters the header that indicates
IPPROTO_TCP.  In addition I have added checks to verify that the lowest
protocol provided is recognized as IPv4 or IPv6 to help mitigate raw
sockets using ETH_P_ALL from having ATR applied to them.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The VXLAN port number should be stored in network order instead of in host
order as it is accessed from the hot-path in ATR.  This way we can avoid
having to do any byte swaps in order to validate the port number.

I moved the vxlan_port value into a hole in the read-mostly region of the
adapter struct.  This way it should be in a warm cache-line instead of in
some isolated region in memory when it needs to be accessed.

In addition I went through and stripped a bunch of unneeded ifdef flags
since having an extra variable present doesn't really hurt anything and
makes the code easier to read.  I also went through and dropped the
NETIF_F_RXCSUM flag which was being set in hw_encap_features but provides
no value as the flag is not evaluated in the Rx path.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

commit c9f53e63 ("ixgbe: Refactor MAC address configuration code")
introduced code that doesn't set HW register RAR0 to default mac address
but FF:FF:FF:FF:FF:FF. Due to this, ixgbe HW discards all incoming packets
that doesn't have destination mac address equals to FF:FF:FF:FF:FF:FF.

This commit sets RAR0 correctly to default HW mac address.
Signed-off-by: NTushar Dave <tushar.n.dave@oracle.com>
Tested-by: NSowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The success of CMA allocation largely depends on the success of
migration and key factor of it is page reference count.  Until now, page
reference is manipulated by direct calling atomic functions so we cannot
follow up who and where manipulate it.  Then, it is hard to find actual
reason of CMA allocation failure.  CMA allocation should be guaranteed
to succeed so finding offending place is really important.

In this patch, call sites where page reference is manipulated are
converted to introduced wrapper function.  This is preparation step to
add tracepoint to each page reference manipulation function.  With this
facility, we can easily find reason of CMA allocation failure.  There is
no functional change in this patch.

In addition, this patch also converts reference read sites.  It will
help a second step that renames page._count to something else and
prevents later attempt to direct access to it (Suggested by Andrew).
Signed-off-by: NJoonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: NMichal Nazarewicz <mina86@mina86.com>
Acked-by: NVlastimil Babka <vbabka@suse.cz>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I added this check in setup_tc to multiple drivers,

 if (handle != TC_H_ROOT || tc->type != TC_SETUP_MQPRIO)

Unfortunately restricting to TC_H_ROOT like this breaks the old
instantiation of mqprio to setup a hardware qdisc. This patch
relaxes the test to only check the type to make it equivalent
to the check before I broke it. With this the old instantiation
continues to work.

A good smoke test is to setup mqprio with,

# tc qdisc add dev eth4 root mqprio num_tc 8 \
  map 0 1 2 3 4 5 6 7 \
  queues 0@0 1@1 2@2 3@3 4@4 5@5 6@6 7@7

Fixes: e4c6734e ("net: rework ndo tc op to consume additional qdisc handle paramete")
Reported-by: NSingh Krishneil <krishneil.k.singh@intel.com>
Reported-by: NJake Keller <jacob.e.keller@intel.com>
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: Or Gerlitz <ogerlitz@mellanox.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the original series drivers would get offload requests for cls_u32
rules even if the feature bit is disabled. This meant the driver had
to do a boiler plate check on the feature bit before adding/deleting
the rule.

This patch lifts the check into the core code and removes it from the
driver specific case.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch ensures ixgbe will not try to offload hash tables from the
u32 module. The device class does not currently support this so until
it is enabled just abort on these tables.

Interestingly the more flexible your hardware is the less code you
need to implement to guard against these cases.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds initial support for offloading the u32 tc classifier. This
initial implementation only implements a few base matches and actions
to illustrate the use of the infrastructure patches.

However it is an interesting subset because it handles the u32 next
hdr logic to correctly map tcp packets from ip headers using the ihl
and protocol fields. After this is accepted we can extend the match
and action fields easily by updating the model header file.

Also only the drop action is supported initially.

Here is a short test script,

 #tc qdisc add dev eth4 ingress
 #tc filter add dev eth4 parent ffff: protocol ip \
	u32 ht 800: order 1 \
	match ip dst 15.0.0.1/32 match ip src 15.0.0.2/32 action drop

<-- hardware has dst/src ip match rule installed -->

 #tc filter del dev eth4 parent ffff: prio 49152
 #tc filter add dev eth4 parent ffff: protocol ip prio 99 \
	handle 1: u32 divisor 1
 #tc filter add dev eth4 protocol ip parent ffff: prio 99 \
	u32 ht 800: order 1 link 1: \
	offset at 0 mask 0f00 shift 6 plus 0 eat match ip protocol 6 ff
 #tc filter add dev eth4 parent ffff: protocol ip \
	u32 ht 1: order 3 match tcp src 23 ffff action drop

<-- hardware has tcp src port rule installed -->

 #tc qdisc del dev eth4 parent ffff:

<-- hardware cleaned up -->
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates setup_tc so we can pass additional parameters into
the ndo op in a generic way. To do this we provide structured union
and type flag.

This lets each classifier and qdisc provide its own set of attributes
without having to add new ndo ops or grow the signature of the
callback.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ndo_setup_tc() op was added to support drivers offloading tx
qdiscs however only support for mqprio was ever added. So we
only ever added support for passing the number of traffic classes
to the driver.

This patch generalizes the ndo_setup_tc op so that a handle can
be provided to indicate if the offload is for ingress or egress
or potentially even child qdiscs.

CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: Or Gerlitz <ogerlitz@mellanox.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is an opportunity to bulk free SKBs during reclaiming of
resources after DMA transmit completes in ixgbe_clean_tx_irq.  Thus,
bulk freeing at this point does not introduce any added latency.

Simply use napi_consume_skb() which were recently introduced.  The
napi_budget parameter is needed by napi_consume_skb() to detect if it
is called from netpoll.

Benchmarking IPv4-forwarding, on CPU i7-4790K @4.2GHz (no turbo boost)
 Single CPU/flow numbers: before: 1982144 pps ->  after : 2064446 pps
 Improvement: +82302 pps, -20 nanosec, +4.1%
 (SLUB and GCC version 5.1.1 20150618 (Red Hat 5.1.1-4))

Joint work with Alexander Duyck.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Right now ATR is not handling IPv6 extended headers, so ATR is not
being performed on such packets. Fix that by skipping extended
headers when they are present. This also fixes a problem where
the ATR code was not checking that the inner protocol was actually
TCP before setting up the signature rules. Since the protocol check
is intimately involved with the extended header processing as well,
this all gets fixed together.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When FCoE is enabled with SR-IOV on the X550 NIC the hardware
generates MDD events.

This patch fixes these by setting the expected values in the
Tx context descriptors for FCoE/FIP frames and adding a flush
after writing the RDLEN register.
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If an outer UDP checksum is set, pass the skb up with CHECKSUM_NONE
so that the stack will check the checksum. Do not increment an
error counter, because we don't know that there is an actual error.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Clean up minor redundancy in the setting of hw_enc_features that
makes it appears that X550 uniquely has more encapsulation features
than other devices. The driver only supports one more feature, so
make it look that way. No longer set NETIF_F_SG since that is set
by the register_netdev call. Thanks to Alex Duyck for noticing this
slight confusion.
Reported-by: NAlexander Duyck <aduyck@mirantis.com>
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The name NETIF_F_ALL_CSUM is a misnomer. This does not correspond to the
set of features for offloading all checksums. This is a mask of the
checksum offload related features bits. It is incorrect to set both
NETIF_F_HW_CSUM and NETIF_F_IP_CSUM or NETIF_F_IPV6 at the same time for
features of a device.

This patch:
  - Changes instances of NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK (where
    NETIF_F_ALL_CSUM is being used as a mask).
  - Changes bonding, sfc/efx, ipvlan, macvlan, vlan, and team drivers to
    use NEITF_F_HW_CSUM in features list instead of NETIF_F_ALL_CSUM.
Signed-off-by: NTom Herbert <tom@herbertland.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SCTP checksum is really a CRC and is very different from the
standards 1's complement checksum that serves as the checksum
for IP protocols. This offload interface is also very different.
Rename NETIF_F_SCTP_CSUM to NETIF_F_SCTP_CRC to highlight these
differences. The term CSUM should be reserved in the stack to refer
to the standard 1's complement IP checksum.
Signed-off-by: NTom Herbert <tom@herbertland.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is a follow-on for enabling VLAN promiscuous and allowing the PF
to add VLANs without adding a VLVF entry.  What this patch does is go
through and free the VLVF registers if they are not needed as the VLAN
belongs only to the PF which is the default pool.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for VLAN promiscuous with SR-IOV enabled.

The code prior to this patch was only adding the PF to VLANs that the VF
had added.  As such enabling promiscuous mode would actually not add any
additional VLAN filters so visibility was limited.  This lead to a number
of issues as the bridge and OVS would expect us to accept all VLAN tagged
packets when promiscuous mode was enabled, and instead we would filter out
most if not all depending on the configuration of the PF.

With this patch what we do is set all the bits in the VFTA and all of the
VLVF bits associated with the pool belonging to the PF.  By doing this the
PF is guaranteed to receive all VLAN tagged traffic associated with the RAR
filters assigned to the PF.  In addition we will clean up those same bits
in the event of promiscuous mode being disabled.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for bypassing the VLVF entry creation when the PF
is adding a new VLAN.  The advantage to doing this is that we can then save
the VLVF entries for the VFs which must have them in order to function,
versus the PF which can fall back on the default pool entry.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add a check to make certain mac_table was actually allocated and is not
NULL.  If it is NULL return -ENOMEM and allow the probe routine to fail
rather then causing a NULL pointer dereference further down the line.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Enabling SR-IOV and then bringing the interface up was resulting in the PF
MAC addresses getting into a bad state.  Specifically the MAC address was
enabled for both VF 0 and the PF.  This resulted in some odd behaviors such
as VF 0 receiving a copy of the PFs traffic, which in turn enables the
ability for VF 0 to spoof the PF.

A workaround for this issue appears to be to bring up the interface first
and then enable SR-IOV as this way the reset is then triggered in the
existing code.

In order to correct this I have added a change to ixgbe_setup_tc where if
the interface is down we still will at least call ixgbe_reset so that the
MAC addresses for the device are reset to the correct pools.

Steps to reproduce issue:
modprobe ixgbe
echo 7 > /sys/bus/pci/devices/0000\:01\:00.1/sriov_numvfs
ifconfig enp1s0f1 up
ethregs -s 1:00.1 | grep MPSAR | grep -v 00000000

Result:
	MPSAR[0]               00000081
	MPSAR[254]             00000001

Expected Result, behavior after patch:
	MPSAR[0]               00000080
	MPSAR[254]             00000080
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NDarin Miller <darin.j.miller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Check for and handle IPv6 extended headers so that Tx checksum
offload can be done. Also use skb_checksum_help for unexpected
cases. Thanks to Tom Herbert for noticing these problems. Thanks
to Alexander Duyck for recognizing problems with the first version
of this patch and recognizing how to coalesce error conditions
into a single location.
Reported-by: NTom Herbert <tom@herbertland.com>
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Save VF device pointers and take references to speed accesses used
to monitor the device behavior to avoid slot resets. The saved
information avoids lock contention during the search used to access
each of the VFs.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NDarin Miller <darin.j.miller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The X550EM_x devices handle clocking differently, so update the
PTP implementation to accommodate them. This involves significant
changes to ixgbe's PTP code to accommodate the new range of
behaviors including things like non-power-of-2 clock wrapping.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NDarin Miller <darin.j.miller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>