The MC13783 Chip Errata, Rev. 4 says, that depending on SPI clock
and main audio clock speed, the Audio Codec or Stereo DAC do sometimes
not start when programmed to do so. This is due to an internal clock
timing issue related to the loading of the SPI bits into the audio block.

On an i.MX27 based system, this issue lead to switched audio channels under
certain circumstances: RTC + Touch + Audio are used and loaded at startup.

The mentioned workaround of writing registers 40 and 41 two times is implemented
here.
Signed-off-by: NSteffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: NMark Brown <broonie@linaro.org>

On a mx28 board, running "aplay -l" and "arecord -l" results in the following:

$ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: mxssgtl5000 [mxs_sgtl5000], device 0: Playback sgtl5000-0 []
  Subdevices: 1/1
  Subdevice #0: subdevice #0
card 0: mxssgtl5000 [mxs_sgtl5000], device 1: Capture sgtl5000-1 []
  Subdevices: 1/1
  Subdevice #0: subdevice #0

$ arecord -l
**** List of CAPTURE Hardware Devices ****
card 0: mxssgtl5000 [mxs_sgtl5000], device 0: Playback sgtl5000-0 []
  Subdevices: 1/1
  Subdevice #0: subdevice #0
card 0: mxssgtl5000 [mxs_sgtl5000], device 1: Capture sgtl5000-1 []
  Subdevices: 1/1
  Subdevice #0: subdevice #0

,which is not correct because we got a capture device listed in aplay and a
playback device listed in arecord.

On mx28 there are two serial audio interface ports (SAIF0 and SAIF1) and each
one of them are unidirectional.

Allow to specify a dai link as 'playback_only' or 'capture_only', which suits
well for this case.

After this change we can correctly report the capabilities as follows:

$ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: mxssgtl5000 [mxs_sgtl5000], device 0: HiFi Playback sgtl5000-0 []
  Subdevices: 1/1
  Subdevice #0: subdevice #0

$ arecord -l
**** List of CAPTURE Hardware Devices ****
card 0: mxssgtl5000 [mxs_sgtl5000], device 1: HiFi Capture sgtl5000-1 []
  Subdevices: 1/1
  Subdevice #0: subdevice #0

Also tested playback and capture on the mx28evk board.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Add 'playback_only' and 'capture_only' fields that can be used for specifying
that a dai_link has a unidirectional capability.

The motivation for this is for the cases of systems, such as Freescale MX28,
that has two unidirectional DAIs.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NMark Brown <broonie@linaro.org>
Acked-by: NNicolin Chen <B42378@freescale.com>

The ssm2602 uses regmap for caching not soc-cache, so we need to use
regcache_sync() instead of snd_soc_cache_sync().
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

The sysfs_registered field was added to the snd_soc_codec struct in commit
f0fba2ad ("ASoC: multi-component - ASoC Multi-Component Support"), but has never
been used.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

The DAPM context struct has its own field where it stores the pointer to the
DAPM debugfs entry. The debugfs_dapm field in the snd_soc_platform and
snd_soc_codec structs are completely unused and can be removed.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

The control_type field was used by the core to track which raw IO methods to
use, but when switching to regmap this was no longer necessary and so the last
user of the field was removed in commit be3ea3b9 ("ASoC: Use new register map
API for ASoC generic physical I/O"). The field is now completely unused and can
be removed.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

There is a blank space missing between ':=' and 'imx-spdif.o', thus add it.
Signed-off-by: NNicolin Chen <b42378@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Add wrapping '\n' for dev_dbg() in fsl_spdif.c
Signed-off-by: NNicolin Chen <b42378@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NBard Liao <bardliao@realtek.com>
Tested-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

We need to make sure that the control's cached value is initialized to the same
value as the control's widget->on_val. Otherwise updates might be lost.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

Merge tag 'asoc-v3.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next

ASoC: Updates for v3.12

A few more updates for v3.12, mostly small cleanups plus the addition of
the DT bindings for kirkwood and the new i.MX S/PDIF driver.

SND_SOC_FSL_UTILS is only used by PowerPC machines, so let's drop it in the
i.mx case.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NNicolin Chen <b42378@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

The legacy S3C-DMA API required every period of a cyclic buffer to be
queued separately. After conversion of Samsung ASoC to Samsung DMA
wrappers somebody made an assumption that the same is needed for DMA
engine API, which is not true.

In effect, Samsung ASoC DMA code was queuing the whole cyclic buffer
multiple times with a shift of one period per iteration, leading to:
  a) severe memory waste - up to 13x times more DMA transfer descriptors
     are allocated than needed,
  b) possible memory corruption, because further cyclic buffers were out
     of the original buffers, due to the offset.

This patch fixes this problem by making the legacy S3C-DMA API use the
same semantics as DMA engine (the whole cyclic buffer is enqueued at
once) and modifying users of Samsung DMA wrappers in cyclic mode to
behave appropriately.
Signed-off-by: NTomasz Figa <tomasz.figa@gmail.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

Driver core clears the driver data to NULL after device_release or on probe
failure, so just remove it from here.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Driver core clears the driver data to NULL after device_release or on probe
failure, so just remove it from here.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NMark Brown <broonie@linaro.org>

This patch implements a device-tree-only machine driver for Freescale
i.MX series Soc. It works with spdif_transmitter/spdif_receiver and
fsl_spdif.c drivers.
Signed-off-by: NNicolin Chen <b42378@freescale.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

This patch permits the generation of the Kirkwood audio driver which
may be used in the Dove boards.
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMark Brown <broonie@linaro.org>

snd_soc_dapm_new_widgets() works on the ASoC card as a whole not on a specific
DAPM context. The DAPM context that is passed as the parameter is only used to
look up the pointer to the card. This patch updates the signature of
snd_soc_dapm_new_widgets() to take the card directly.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

Call snd_soc_dapm_new_widgets() before the auto non-connected pins have been
marked as not connected will power the system under the assumption that those
pins are connected. Once the pins have been marked as disconnected the system
there will be an additional power run. This can cause unnecessary power
transitions. Calling snd_soc_dapm_new_widgets() only after the pins have been
marked as non-connected avoids this.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

Each time snd_soc_dapm_new_widgets() is called it will instantiate all the
widgets and routes that have been added so far and then power them. Doing this
multiple times before the card is fully initialized and all widgets have been
added can cause unnecessary and even invalid power state transitions which can
result in extra register writes and and also might cause clicks and pops.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

snd_soc_jack_add_pins() does not create any new DAPM widgets, so there is no
need to call snd_soc_dapm_new_widgets().
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>