- 12 5月, 2009 2 次提交
-
-
由 Johannes Berg 提交于
There really is no need to have a separate struct for a single variable. The fact that it exists is due to the code legacy, but we can remove that now. Very simple. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
It's not needed outside iwl-core.c Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Acked-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 07 5月, 2009 3 次提交
-
-
由 Reinette Chatre 提交于
Some issues in PS prevent us from supporting it reliably. When 4965 goes to sleep it stores some data in host DRAM, reads it back when device wakes up. In 4965 there is a problem that the data is not correct when ucode starts using it upon wakeup. For all iwlagn devices there is a problem where command is sent when PS is enabled. At the moment there is a locking problem with priv->lock not being held and thus not requesting nic access correctly. We disable PS until these issues have been resolved. Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
The config_interface method is a little strange, it contains the BSSID and beacon updates, while bss_info_changed contains most other BSS information for each interface. This patch removes config_interface and rolls all the information it previously passed to drivers into bss_info_changed. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
We currently have two beacon interval configuration knobs: hw.conf.beacon_int and vif.bss_info.beacon_int. This is rather confusing, even though the former is used when we beacon ourselves and the latter when we are associated to an AP. This just deprecates the hw.conf.beacon_int setting in favour of always using vif.bss_info.beacon_int. Since it touches all the beaconing IBSS code anyway, we can also add support for the cfg80211 IBSS beacon interval configuration easily. NOTE: The hw.conf.beacon_int setting is retained for now due to drivers still using it -- I couldn't untangle all drivers, some are updated in this patch. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 23 4月, 2009 22 次提交
-
-
由 Mohamed Abbas 提交于
Allow user to config the device all the time but only allow commiting these changes to card if the card is up and running. Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Wey-Yi Guy 提交于
This patch clean up the code for NL80211_IFTYPE_MONITOR mode, priv->iw_mode is set in add_interface, but add_interface is never called for monitor mode. The only way mac80211 informs us about monitor mode is through configuring filter; since iw_mode will never set to NL80211_IFTYPE_MONITOR, modify and remove all the code refer to NL80211_IFTYPE_MONITOR and replace with iwl_is_monitor_mode() function call. Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
This modifies iwlwifi to * no longer build its own probe request, but use mac80211's * therefore, support arbitrary scan IEs (up to the max len) * support multiple scan SSIDs * support passive scanning Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Wey-Yi Guy 提交于
This patch adds interrupt statistics report to debugfs, this can help to understand number of interrupts happened which including HW/SW error for easier and better debugging. in /sys/kernel/debug/ieee80211/phyN/iwlagn/data directory use "cat interrupt" to view the current interrupt counter use "echo 0 > interrupt" to clear interrupt counter Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Daniel C Halperin 提交于
For completeness, we should also make sure that the 3x3 MIMO rates are also checked when seeing if one rxon struct matches another. Signed-off-by: NDaniel C Halperin <daniel.c.halperin@intel.com> Acked-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Mohamed Abbas 提交于
We need to sync rxon_active with changes after we commit rxon_assoc, without rxon_active will still have the old data that cause iwl_send_rxon_assoc to fail with no change in rxon command. Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Abhijeet Kolekar 提交于
3945 can now use iwl_mac_reset_tsf from iwlwifi. Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Abhijeet Kolekar 提交于
3945 can now use iwl_mac_get_tx_stats from iwlwifi. Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Abhijeet Kolekar 提交于
3945 can now use iwl_mac_config_interface from iwlwifi. Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Abhijeet Kolekar 提交于
3945 can now use iwl_mac_config from iwlwifi Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Abhijeet Kolekar 提交于
3945 can now use iwl_mac_remove_interface from iwlwifi Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Abhijeet Kolekar 提交于
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Abhijeet Kolekar 提交于
3945 can now use iwl_set_mode from iwlcore library. Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Abhijeet Kolekar 提交于
add set_rxon_chain op to iwlwifi cfg ops in preparation of future 3945 porting work. Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Abhijeet Kolekar 提交于
Patch replaces station management functions with ops declared. Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Abhijeet Kolekar 提交于
3945 can use iwl_mac_beacon_update. Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Abhijeet Kolekar 提交于
3945 can use iwl_bss_info_changed. A new lib op is created for post_assoicate to distinguish between 3945 and iwlwifi's post_associate operations. Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Wey-Yi Guy 提交于
Adding ht triple_stream_basic_rates for MIMO3 supports Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
This patch introduces a new attribute for a wiphy that tells userspace how long the information elements added to a probe request frame can be at most. It also updates the at76 to advertise that it cannot support that, and, for now until I can fix that, iwlwifi too. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Reinette Chatre 提交于
The STATUS_ALIVE value cannot be used because it is cleared when interface is brought down and will not be set if rfkill is enabled when interface is started again. The interface can thus not be brought up if rfkill was enabled before stopping the interface and disabled after starting the interface. Change the test to use priv->is_open instead, this will be set when interface is started whether rfkill is enabled or not. Thanks to Helmut Schaa for the suggested fix. Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Abhijeet Kolekar 提交于
3945 now uses iwl_mac_conf_tx. Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Wey-Yi Guy 提交于
With mac80211's help to call stop() and start() in mac80211 suspend/resume function, both iwlagn and iwl3945 no longer calling stop() and start(); remove un-necessary STATUS_IN_SUSPEND bit from both header files and functions, Move apm_ops.stop() function into pci_suspend() to ensure DMA is stopped before go into suspend mode. iwl3945 has the similar suspend/resume function as iwlagn, so move both functions to iwlcore to be shared by both drivers. Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 28 3月, 2009 3 次提交
-
-
由 Johannes Berg 提交于
This patch removes all the virtual A-MPDU-queue bookkeeping from mac80211. Curiously, iwlwifi already does its own bookkeeping, so it doesn't require much changes except where it needs to handle starting and stopping the queues in mac80211. To handle the queue stop/wake properly, we rewrite the software queue number for aggregation frames and internally to iwlwifi keep track of the queues that map into the same AC queue, and only talk to mac80211 about the AC queue. The implementation requires calling two new functions, iwl_stop_queue and iwl_wake_queue instead of the mac80211 counterparts. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Cc: Reinette Chattre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Mohamed Abbas 提交于
Set IEEE80211_HW_SPECTRUM_MGMT bit in hw->flags, this tell mac80211 we support spectrum mgmt. Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Mohamed Abbas 提交于
In function iwl_mac_config use changed flag to call only the affected functions. This patch also allow user to cache channel, txpower and power value when the interface is not ready and apply the changes once the interface ready. Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 06 3月, 2009 1 次提交
-
-
由 Abhijeet Kolekar 提交于
3945 can use iwl_activate_qos instead of iwl3945_activate_qos. Patch does two things 1) Patch adds iwl_activate_qos in core library. 2) 3945 makes use of iwl_activate_qos. Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 28 2月, 2009 4 次提交
-
-
由 Abhijeet Kolekar 提交于
iwl3945 uses iwl_isr and deletes duplicated iwl3945_isr. Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Acked-by: NSamuel Ortiz <samuel.ortiz@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Abhijeet Kolekar 提交于
Patch removes duplicate code from iwl3945 and uses iwl_rx_reply_error and spectrum notifications from iwlwifi. Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Acked-by: NSamuel Ortiz <samuel.ortiz@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Abhijeet Kolekar 提交于
Patch removes duplicate rx handlers(pm_sleep and pm_debug) from 3945 and uses handlers from iwlwifi. Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Acked-by: NSamuel Ortiz <samuel.ortiz@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Wu, Fengguang 提交于
Signed-off-by: NWu Fengguang <fengguang.wu@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 14 2月, 2009 1 次提交
-
-
由 Johannes Berg 提交于
This patch adds basic scan capability to cfg80211/nl80211 and changes mac80211 to use it. The BSS list that cfg80211 maintains is made driver-accessible with a private area in each BSS struct, but mac80211 doesn't yet use it. That's another large project. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 10 2月, 2009 3 次提交
-
-
由 Winkler, Tomas 提交于
This patch unifies 3945 and iwlagn power save management This patch also better separates system state from user setting. System state shall be removed later as this shall be shifted to user space Signed-off-by: NTomas Winkler <tomas.winkler@intel.com> Acked-by: NMohamed Abbas <mohamed.abbas@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Tomas Winkler 提交于
Call IWL_DEBUG macro with explicit priv argument. Signed-off-by: NTomas Winkler <tomas.winkler@intel.com> Acked-by: NSamuel Ortiz <samuel.ortiz@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Samuel Ortiz 提交于
The iwl_rxon_cmd is really just a iwl3945_rxon_cmd structure extension. So, we can use the *_rxon fields from iwl_priv instead of the 3945 specific ones (*39_rxon). We have to then be careful when submitting REPLY_RXON host commands, since the command length as to be set according to the HW. As another precaution the reserved4 and reserved5 fields are cleared before being sent to the 3945. With the *39_rxon removal, a lot of duplicated code can be removed from the 3945 code base. Signed-off-by: NSamuel Ortiz <samuel.ortiz@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 30 1月, 2009 1 次提交
-
-
由 Samuel Ortiz 提交于
With the recent host command routines merge, we can now look at the various host command helpers and get rid of the duplicated ones. Signed-off-by: NSamuel Ortiz <samuel.ortiz@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-