There really is no need to have a separate struct for a
single variable. The fact that it exists is due to the
code legacy, but we can remove that now. Very simple.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The lower 4 bytes of the chipset revision must contain
a non-zero value. This bug was introduced by
"rt2x00: Simplify rt2x00_check_rev".
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It's not needed outside iwl-core.c
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

m68k allmodconfig:
| drivers/net/wireless/wl12xx/main.c: In function 'wl12xx_probe':
| drivers/net/wireless/wl12xx/main.c:1273: error: implicit declaration of function 'set_irq_type'
| make[1]: *** [drivers/net/wireless/wl12xx/main.o] Error 1
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Acked-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ETH_P_SLOW is already defined in include/linux/if_ether.h.
There's no need to define BOND_ETH_P_LACPDU in drivers/net/bonding/bond_3ad.h
Signed-off-by: NRichard Genoud <richard.genoud@gmail.com>
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove unnecessary length parameter since it's always 4 bytes.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This board doesn't suppot msi-x well due to msi-x table
mapping (hardware) issue.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Fix the order of irq and hardware context teardown.
  Also synchronize the interrupt in dev close() before
  releasing tx buffers.

o Fix possible msi-x vector leak if available vectors are
  less than requested.

o Request multiple msix vectors only if hardware supports
  multiple rx queues.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Store msi target status register offset in adapter struct.
This avoids contention on msi_tgt_status table from interrupt
hadlers of different pci function.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fix size of remaped iomem, which is 1 byte to small
(e.g. mappes only 0xff bytes instead of 0x100)
Signed-off-by: NMatthias Ludwig <mludwig@ultratronik.de>
Acked-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

after the recent changes to wired drivers to use only
netif_carrier_off the driver can have outstanding tx work to
complete that will never complete once link is down.  Since the
intel hardware will hold this tx work forever, the driver
notices a tx timeout condition internally and might try
to instigate printk and reset of the part with a
netif_stop_queue, which doesn't work because link is down.

Don't bother arming to tx hang detection when link is down.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make sure we don't get any sign-extend issues when we shift a 1
into bit 31.
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We weren't logging the 82598AT fan failure if it occurred before (ixgbe_open)
as we hadn't sent up to catch the interrupt that event caused.

This patch checks for this failure in:
ixgbe_probe - So we can log the failure asap. We check right after we
set up the adapter->flags, which is when we know that we have a fan.
ixgbe_up_complete - To catch failures that may have happened between probe
and when we set up the interrupt that would normally detect the fan failure.

To enable all of this we need to initialize the adapter flag with
IXGBE_FLAG_FAN_FAIL_CAPABLE when the NIC contained a fan.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This enables L2 header split when packet split is enabled for 82599.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current configuration is not setting queue 0 correctly for DCB
configurations.  As a result unconfigured queues are being used to setup
the SRRCTL register rx buffer len sizes.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As per the documentation for 82599 in order to support hardware RSC the
header size must be set.  This is only currently done for packet split
mode.  This patch sets the header buffer length for all modes.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add barrier() to bnx2_get_hw_{tx|rx}_cons() to fix this issue:

http://bugzilla.kernel.org/show_bug.cgi?id=12698

This issue was reported by multiple i386 users.  Without barrier(),
the compiled code looks like the following where %eax contains the
address of the tx_cons or rx_cons in the DMA status block.  The
status block contents can change between the cmpb and the movzwl
instruction.  The driver would crash if the value was not 0xff during
the cmpb instruction, but changed to 0xff during the movzwl
instruction.

6828:	80 38 ff             	cmpb   $0xff,(%eax)
682b:	0f b7 10             	movzwl (%eax),%edx

With the added barrier(), the compiled code now looks correct:

683d:	0f b7 10             	movzwl (%eax),%edx
6840:	0f b6 c2             	movzbl %dl,%eax
6843:	3d ff 00 00 00       	cmp    $0xff,%eax

Thanks to Pascal de Bruijn <pmjdebruijn@pcode.nl> for reporting the
problem and Holger Noefer <hnoefer@pironet-ndh.com> for patiently
testing test patches for us.

Also updated version to 2.0.1.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The setup_rctl call was making a call into the ring structure after it had
been freed.  This was causing a panic on shutdown.  This call wasn't
necessary since it is possible to get the needed index from
adapter->vfs_allocated_count.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Traditionally Intel based NIC drivers request I/O port even though it
doesn't need that really.

Intel PCIE 10Gb driver (ixgbe) also requests I/O port but it doesn't
need it either.

This is a little inconvenient situation because sometimes we have to
handle those cards on the slots where any I/O space is not attached.

So we made pach which makes ixgbe driver legacy I/O port free.
Signed-off-by: NMasayuki Gouji <gouji.masayuki@jp.fujitsu.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to the "PCI Error Recovery" document, if after a recovery,
the bus is disabled, the error_detected function should return
PCI_ERS_RESULT_DISCONNECT. Actually ixgbe error_detected function is
always returning PCI_ERS_RESULT_NEED_RESET, even if the bus is in failure.
This patch just check if the bus is disabled and then returns
PCI_ERS_RESULT_DISCONNET.
Signed-off-by: NBreno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There were still some references to napi_add/del_all left after the dynamic
vector allocation patch.  This patch removes those references since the
ixgbe_napi_add/del_all calls are no longer needed as the napi struct is
added when the vector is created, and deleted when the vector is freed.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

currently ixgbe_receive_skb is passing the vector index to
skb_record_rx_queue instead of the queue index.  This patch changes that so
that the ring index is passed instead.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the q_vectors are being allocated statically inside of the
adapter struct.  This increases the overall size of the adapter struct when
we can easily allocate the vectors dynamically.  This patch changes that
behavior so that the q_vectors are allocated dynamically and the napi
structures are automatically allocated inside of the q_vectors as needed.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An issue was found in which rx checksum could not be enabled without
resetting the interface.  The issue was the hardware enable was not being
done via ethtool.  To resolve this issue and prevent conflicts with VF
configuration we will leave the feature always enabled in hardware, and
then in software we will choose to ignore the results via a sw flag.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch cleans up a number of unused or unneeded feature flags.  As a
result of these changes the user should now be able to enable or disable rx
checksumming via ethtool.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is not a good idea to blindly unmask the RX and TX_END interrupts
for all eight queues on all mv643xx_eth hardware, since some variations
of the hardware have less than eight transmit/receive queues, and the
RX/TX_END interrupts for the queues they don't have can be in use by
other interrupt sources.
Signed-off-by: NSaeed Bishara <saeed@marvell.com>
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On the platforms that mv643xx_eth is used on, the manual skb->data
alignment logic in mv643xx_eth can be simplified, as the only case we
need to handle is where NET_SKB_PAD is not a multiple of the cache
line size.  If this is the case, the extra padding we need can be
computed at compile time, while if NET_SKB_PAD _is_ a multiple of
the cache line size, the code can be optimised out entirely.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the definitions for the SDMA and port serial configuration
register values to where all the other register definitions live,
and expand the shifts to 32 bit constants.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Pause traffic during mac addr change.
o Enable setting mac address for NX3031.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o use standard linked list api for mac addr list management
  in NX3031.
o release mac addresses in firmware in dev close().
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the distance check between tx ring producer and consumer that
could lead to tx ring wrap around.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The AR_SREV_9285_1[12]_OR_LATER macros already contains the
AR_SREV_9285 check.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On x86 this allows us to do the following small savings:
shave off 23 % off of the module's data, and
shave off 6  % off of the module's text.

We save 456 bytes, for those counting.

$ size ath9k.ko
   text    data     bss     dec     hex filename
 250794    3628    1600  256022   3e816 ath9k.ko
$ size ath9k-old.ko
   text    data     bss     dec     hex filename
 239114   15308    1600  256022   3e816 ath9k-old.ko

$ du -b ath9k.ko
4034244 ath9k.ko
$ du -b ath9k-old.ko
4033788 ath9k-old.ko
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently queues are stopped when their length reaches their length limit,
but are restarted only when the size of freed range of packet buffer is
not less than the size of the largest possible packet.

This causes permanent queue stop on radio visibility loss in the middle
of ping series: there is plenty of room in the packet buffer, but it is
never freed more than 3 (size of 'best effort' queue) * 288 (ping packet
plus headers) bytes at once.
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt2x00_check_rev() was too specific for rt2500usb and rt73usb,
by adding the mask argument (instead of hardcoding it into
the function itself) we can use the function in rt2800usb as
well.

v2: Fix revision mask for rt2800usb
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Ooops...
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>