The mvneta is also used in some Marvell berlin family SoCs which may
have 64bytes cacheline size. Replace the MVNETA_CPU_D_CACHE_LINE_SIZE
usage with L1_CACHE_BYTES.

And since dma_alloc_coherent() is always cacheline size aligned, so
remove the align checks.
Signed-off-by: NJisheng Zhang <jszhang@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mvpp2 ip maybe used in SoCs which may have have 64bytes cacheline
size. Replace the MVPP2_CPU_D_CACHE_LINE_SIZE with L1_CACHE_BYTES.

And since dma_alloc_coherent() is always cacheline size aligned, so
remove the align checks.
Signed-off-by: NJisheng Zhang <jszhang@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To report flow control tx/rx settings accurately regardless of autoneg
setting, we should use link_info->req_flow_ctrl.  Before this patch,
the reported settings were only correct when autoneg was on.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The typo caused the wrong flow control bit to be set.

Reported by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The size of every padded firmware message is specified in the first
HWRM_VER_GET response message.  Use this value to pad every message
after that.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The existing code does the following:
    allocate completion ring
    initialize completion ring doorbell
    disable interrupts on this completion ring by writing to the doorbell

We can have a race where firmware sends an asynchronous event to the host
after completion ring allocation and before doorbell is initialized.
When this happens driver can crash while ringing the doorbell using
uninitialized value as part of handling the IRQ/napi request.
Signed-off-by: NPrashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

in the case where qed_slowpath_irq_req is not called, rc is not
assigned and so qed_int_igu_enable will return a garbage value.
Fix this by initializing rc to 0.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix support for 16 bit source/dest port matches in ixgbe model.
u32 uses a single 32-bit key value for both source and destination ports
starting at offset 0. So replace the 2 functions with a single function
that takes this key value/mask to program both source and dest ports.

Verified with the following filter:

 #tc qdisc add dev p4p1 ingress
 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
	handle 1: u32 divisor 1
 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
	handle 800:0:10 u32 ht 800: link 1: \
	offset at 0 mask 0f00 shift 6 plus 0 eat match ip protocol 6 ff
 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
	handle 1:0:10 u32 ht 1: \
	match tcp src 1024 ffff match tcp dst 80 ffff action drop
 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
	handle 1:0:11 u32 ht 1: \
	match tcp src 1025 ffff action drop
 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
	handle 1:0:12 u32 ht 1: \
	match tcp dst 81 ffff action drop
Signed-off-by: NSridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove the incorrect check for mask in ixgbe_configure_clsu32 and
drop the 'mask' field that is not required in struct ixgbe_mat_field

Verified with the following filters:

 #tc qdisc add dev p4p1 ingress
 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
	handle 800:0:1 u32 ht 800: \
	match ip dst 10.0.0.1/8 match ip src 10.0.0.2/8 action drop
 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
	handle 800:0:2 u32 ht 800: \
	match ip dst 11.0.0.1/16 match ip src 11.0.0.2/16 action drop
 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
	handle 800:0:3 u32 ht 800: \
	match ip dst 12.0.0.1/24 match ip src 12.0.0.2/24 action drop
 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
	handle 800:0:4 u32 ht 800: \
	match ip dst 13.0.0.1/32 match ip src 13.0.0.2/32 action drop
Signed-off-by: NSridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Check for handle ids when adding/deleting hash nodes OR adding/deleting
filter entries and limit them to max number of links or header nodes
supported(IXGBE_MAX_LINK_HANDLE).

Start from bit 0 when setting hash table bit-map.(adapter->tables)
Signed-off-by: NSridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This function is only used in ixgbe_main.c
Resolves a "missing prototype" warning when building the driver with W=1
Reported-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Return error when a MAC address change is rejected by the PF.

This will prevent the user from modifying the MAC address when
that operation is not permitted.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Calling dev_close() causes IFF_UP to be cleared which will remove the
interfaces routes and some addresses. That's probably not what the user
intended when running the offline selftest. Besides this does not happen
if the interface is brought down before the test, so the current
behaviour is inconsistent.
Instead call the net_device_ops ndo_stop function directly and avoid
touching IFF_UP at all.
Signed-off-by: NStefan Assmann <sassmann@kpanic.de>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Calling dev_close() causes IFF_UP to be cleared which will remove the
interfaces routes and some addresses. That's probably not what the user
intended when running the offline selftest. Besides this does not happen
if the interface is brought down before the test, so the current
behaviour is inconsistent.
Instead call the net_device_ops ndo_stop function directly and avoid
touching IFF_UP at all.
Signed-off-by: NStefan Assmann <sassmann@kpanic.de>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use udelay instead of usleep_range because this can be called while
a lock is held.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The ATR code was assuming that it would be able to use tcp_hdr for
every TCP frame that came through.  However this isn't the case as it
is possible for a frame to arrive that is TCP but sent through something
like a raw socket.  As a result the driver was setting up bad filters in
which tcp_hdr was really pointing to the network header so the data was
all invalid.

In order to correct this I have added a bit of parsing logic that will
determine the TCP header location based off of the network header and
either the offset in the case of the IPv4 header, or a walk through the
IPv6 extension headers until it encounters the header that indicates
IPPROTO_TCP.  In addition I have added checks to verify that the lowest
protocol provided is recognized as IPv4 or IPv6 to help mitigate raw
sockets using ETH_P_ALL from having ATR applied to them.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The VXLAN port number should be stored in network order instead of in host
order as it is accessed from the hot-path in ATR.  This way we can avoid
having to do any byte swaps in order to validate the port number.

I moved the vxlan_port value into a hole in the read-mostly region of the
adapter struct.  This way it should be in a warm cache-line instead of in
some isolated region in memory when it needs to be accessed.

In addition I went through and stripped a bunch of unneeded ifdef flags
since having an extra variable present doesn't really hurt anything and
makes the code easier to read.  I also went through and dropped the
NETIF_F_RXCSUM flag which was being set in hw_encap_features but provides
no value as the flag is not evaluated in the Rx path.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

commit c9f53e63 ("ixgbe: Refactor MAC address configuration code")
introduced code that doesn't set HW register RAR0 to default mac address
but FF:FF:FF:FF:FF:FF. Due to this, ixgbe HW discards all incoming packets
that doesn't have destination mac address equals to FF:FF:FF:FF:FF:FF.

This commit sets RAR0 correctly to default HW mac address.
Signed-off-by: NTushar Dave <tushar.n.dave@oracle.com>
Tested-by: NSowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

GPIOlib will print warning messages if we call GPIO functions without a
valid GPIO. Change the code to avoid doing so.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It may fail to set coalesce usecs to HW, and Ethtool needs to know if it
is successful to cfg the parameter or not. So it needs return the errno by
dsaf.ko.
Signed-off-by: NLisheng <lisheng011@huawei.com>
Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The overtime setting and getting REGs in HNS V2 is defferent from HNS V1.
It needs to be distinguished between them if getting or setting the REGs.
Signed-off-by: NLisheng <lisheng011@huawei.com>
Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In ravb_start_xmit dont call skb_tx_timestamp only when hardware
timestamping is requested: in the latter case software timestamps are
suppressed and thus the call of skb_tx_timestamp does not have any effect.

Instead call skb_tx_timestamp unconditionally in ravb_start_xmit, since
the function checks itself if software timestamping is required or should
be skipped due to hardware timestamping.
Signed-off-by: NLino Sanfilippo <LinoSanfilippo@gmx.de>
Acked-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need to use post-decrement to ensure that irq_dispose_mapping is
also called on priv->rxq[0]->irq_no; moreover, if one of the above for
loops failed already at i==0 (so we reach one of these labels with
that value of i), we'll enter an essentially infinite loop of
out-of-bounds accesses.
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes two BUG_ON() used to notify about RX queue corruptions
on macb (not gem) hardware without actually handling the error.

The new code skips corrupted frames but still processes faultless frames.
Then it resets the RX queue before restarting the reception from a clean
state.

This patch is a rework of an older patch proposed by Neil Armstrong:
http://patchwork.ozlabs.org/patch/371525/Signed-off-by: NCyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: NNeil Armstrong <narmstrong@baylibre.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Just updating version as many fixes got
accumulated over 1.00.00.34
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb_len needs to be skb_headlen(skb) in bcmgenet_xmit_single().

Fragmented skbs can have only Ethernet + IP + TCP headers (14+20+20=54 bytes)
in the linear buffer, followed by the rest in fragments. Bumping skb_len to
ETH_ZLEN would be incorrect for this case, as it would introduce garbage
between TCP header and the fragment data.

This also works with regular/non-fragmented small packets < ETH_ZLEN bytes.
Successfully tested this on GENETv3 with 42-byte ARP frames.

For testing, I used:
ethtool -K eth0 tx-checksum-ipv4 off
ethtool -K eth0 tx-checksum-ipv6 off
echo 0 > /proc/sys/net/ipv4/tcp_timestamps

Fixes: 1c1008c7 ("net: bcmgenet: add main driver file")
Signed-off-by: NPetri Gynther <pgynther@google.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. Add bytes_compl local variable to __bcmgenet_tx_reclaim() to collect
   transmitted bytes. dev->stats updates can then be moved outside the
   while-loop. bytes_compl is also needed for future BQL support.
2. When bcmgenet device uses Tx checksum offload, each transmitted skb
   gets an extra 64-byte header prepended to it. Before this header is
   prepended to the skb, we need to save the skb "wire" length in
   GENET_CB(skb)->bytes_sent, so that proper Tx bytes accounting can
   be done in __bcmgenet_tx_reclaim().
3. skb->len covers the entire length of skb, whether it is linear or
   fragmented. Thus, when we clean the fragments, do not increase
   transmitted bytes.

Fixes: 1c1008c7 ("net: bcmgenet: add main driver file")
Signed-off-by: NPetri Gynther <pgynther@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

macb_interrupt() should not use macb_writel(bp, ISR, <value>) but only
queue_writel(queue, ISR, <value>).

There is one IRQ and one set of {ISR, IER, IDR, IMR} [1] registers per
queue on gem hardware, though only queue0 is actually used for now to
receive frames: other queues can already be used to transmit frames.

The queue_readl() and queue_writel() helper macros are designed to access
the relevant IRQ registers.

[1]
ISR: Interrupt Status Register
IER: Interrupt Enable Register
IDR: Interrupt Disable Register
IMR: Interrupt Mask Register
Signed-off-by: NCyrille Pitchen <cyrille.pitchen@atmel.com>
Fixes: bfbb92c4 ("net: macb: Handle the RXUBR interrupt on all devices")
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The hilink status reg in HNS V2 is different from HNS v1. In HNS V2, It
distinguishes differnt lane status according to the bit-field of the reg.
As is shown below:
[0:0] ---> lane0
[1:1] ---> lane1
...

But the current driver reads the reg to get the hilink status ONLY
concidering HNS V1 situation. Here is a patch to support both of them.
Signed-off-by: NSheng Li <lisheng011@huawei.com>
Signed-off-by: NDaode Huang <huangdaode@hisilicon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a misuse of PTR as shown below:

	ae_node = (void *)of_parse_phandle(dev->of_node,
					   "ae-handle",
					   0);
	if (IS_ERR_OR_NULL(ae_node)) {
		ret = PTR_ERR(ae_node);
		dev_err(dev, "not find ae-handle\n");
		goto out_read_prop_fail;
	}

if the ae_node is NULL, PTR_ERR(ae_node) means it returns success. And the
return value should be -ENODEV.
Signed-off-by: NKejian Yan <yankejian@huawei.com>
Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In hns V1, common_poll should check and clean fbd pkts, because it
can not pend irq to clean them if there is no new pkt comes in.
But hns V2 hw fixes this bug, and will pend irq itself to do this.
So, for hns V2, we set ring_data->fini_process to NULL.
Signed-off-by: NSheng Li <lisheng011@huawei.com>
Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The variable head in hns_nic_tx_fini_pro has read a value, but it is
obviously no use. The patch will fix it.
And the comment is nothing to do with the routine, so it has to be removed
Signed-off-by: NQianqian Xie <xieqianqian@huawei.com>
Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The return values in the first two functions mdiobus_write()
are ignored. The patch will fix it.
Signed-off-by: NQianqian Xie <xieqianqian@huawei.com>
Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It misses string format in function snprintf(), as below:
snprintf(buff, ETH_GSTRING_LEN, g_gmac_stats_string[i].desc);

It needs to add "%s" to fix it as below:
snprintf(buff, ETH_GSTRING_LEN, "%s", g_gmac_stats_string[i].desc);
Signed-off-by: NQianqian Xie <xieqianqian@huawei.com>
Signed-off-by: NKejian Yan <yankejian@huawei.com>
Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The cycle index should be varied while the variable j is a fixed value.
The patch will fix this bug.
Signed-off-by: NQianqian Xie <xieqianqian@huawei.com>
Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

devm_ioremap_resource() returns ERR_PTR() value on error, it never
returns NULL, fix it and propagate the returned error upwards.

Fixes: 656e7052 ("net-next: mediatek: add support for MT7623 ethernet")
Signed-off-by: NVladimir Zapolskiy <vz@mleia.com>
Reviewed-by: NMatthias Brugger <mbrugger@suse.com>
Acked-by: NJohn Crispin <blogic@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver calls gpiod_set_value() with GPIOD_OUT_* instead of 0 and 1, as
a result the PHY isn't really  put back into reset state in macb_remove().
Moreover, the driver assumes that something else has set the GPIO direction
to output, so if  it has not, the PHY may not be taken out of reset in
macb_probe() either...
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Errata A-007273 (For FMan V3 devices only):
FMan soft reset is not finished properly if one
of the Ethernet MAC clocks is disabled

Workaround:
Re-enable all disabled MAC clocks through the DCFG_CCSR_DEVDISR2
register prior to issuing an FMAN soft reset.
Re-disable the MAC clocks after the FMAN soft reset is done.
Signed-off-by: NIgal Liberman <igal.liberman@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When set MTU to the minimum value 68, there are increasing number
of error packets occur, which is caused by the overflowed value of
mss. This patch fix the bug.
Signed-off-by: NDaode Huang <huangdaode@hisilicon.com>
Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If mtu for debug port is set more than 1500, it may cause that packets
are dropped by ppe. So maximum value for debug port should be 1500.
Signed-off-by: NKejian Yan <yankejian@huawei.com>
Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>