Add the device tree for the PIKA Warp board
Signed-off-by: NSean MacLennan <smaclennan@pikatech.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This patch extends the Ebony and Walnut platform code to instantiate
the existing ds1742 RTC class driver for the DS1743 RTC/NVRAM chip
found on both those boards.  The patch uses a helper function to scan
the device tree and instantiate the appropriate platform_device based
on it, so it should be easy to extend for other boards which have mmio
mapped RTC chips.

Along with this, the device tree binding for the ds1743 chips is
tweaked, based on the existing DS1385 OF binding found at:
	http://playground.sun.com/1275/proposals/Closed/Remanded/Accepted/346-it.txt
Although that document covers the NVRAM portion of the chip, whereas
here we're interested in the RTC portion, so it's not entirely clear
if that's a good model.

This implements only RTC class driver support - that is /dev/rtc0, not
/dev/rtc, and the low-level get/set time callbacks remain
unimplemented.  That means in order to get at the clock you will
either need a modified version of hwclock which will look at
/dev/rtc0, or you'll need to configure udev to symlink rtc0 to rtc.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

The patch adds the Haleakala dts. The Haleakala is a stripped down
version of the Kilauea (405EX) with only one EMAC and only one PCIe
interface.
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Use cuImage bootwrapper until U-Boot port is completed.
Derived heavily from Linkstation port.
Signed-off-by: NJon Loeliger <jdl@freescale.com>
Acked-by: NAndy Wilcox <andy@protium.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Based on the Kurobox DTS files.
Signed-off-by: NJon Loeliger <jdl@freescale.com>
Acked-by: NAndy Wilcox <andy@protium.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add local bus, flash, and MTD partition nodes to mpc8641_hpcn.dts

Also add compatible field for the soc node, so that it will be picked up
by of_platform_bus_probe().
Signed-off-by: NWade Farnsworth <wfarnsworth@mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add NAND to device tree, and call of_platform_bus_probe().
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This board is also resold by Freescale under the names
"QUICCStart MPC8248 Evaluation System" and "CWH-PPC-8248N-VE".
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Update the MPC8610 HPCD files to support the audio driver.  Update
booting-without-of.txt with information on the SSI device.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add support for UART serial ports using a Freescale QUICCEngine. Update
booting-without-of.txt to define new properties for a QE UART node.  Update
the MPC8323E-MDS device tree to add UCC5 as a UART.  Update the QE library
to support slow UCC devices and modules.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

...thus use fixed-link to register proper "Fixed PHY"
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NVitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This patch adds localbus and pata nodes to use CF IDE interface
on MPC8349E-mITX boards.

Patch also adds code to probe localbus.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Remove device_type = "usb" for 83xx SoC USB controller
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The ULI based boards had the interrupt maps for USB on the ULI incorrectly
set.

Also, the MPC8572DS was missing the interrupt-map-mask for the 3rd PCIe
controller.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add the ability to set the mac address given the alias for the device.
Removes the need for having a linux,network-index property.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Fix typo in arch/powerpc/boot/flatdevtree_env.h.
There is no Documentation/networking/ixgbe.txt.

README.cycladesZ is now in Documentation/.
wavelan.p.h is now in drivers/net/wireless/.
HFS.txt is now Documentation/filesystems/hfs.txt.
OSS-files are now in sound/oss/.
Signed-off-by: NJohann Felix Soden <johfel@users.sourceforge.net>
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch adds support for 'mpc5200-simple-platform' compatible
boards which do not need a platform specific setup. Such boards
are supported assuming the following:

- GPIO pins are configured by the firmware,
- CDM configuration (clocking) is setup correctly by firmware,
- if the 'fsl,has-wdt' property is present in one of the
  gpt nodes, then it is safe to use such gpt to reset the board,
- PCI is supported if enabled in the kernel configuration
  and if there is a PCI bus node defined in the device tree.
Signed-off-by: NMarian Balakowicz <m8@semihalf.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Add device tree source file for Promess Motion-PRO board.
Signed-off-by: NMarian Balakowicz <m8@semihalf.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Add device tree source file for CM5200 board.
Signed-off-by: NMarian Balakowicz <m8@semihalf.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Add device tree source file for TQ Components TQM5200 board.
Signed-off-by: NMarian Balakowicz <m8@semihalf.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Update .gitignore as needed by dtc addition.
Signed-off-by: NJochen Friedrich <jochen@scram.de>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Missed this one in the boot loader before.
Signed-off-by: NStephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This patch adds support for 405GPr processors with optional
new mode strapping. ibm405gp_fixup_clocks() can now be used
for 405GP and 405GPr CPUs.

This is in preparation of porting the cpci405 platform support
from arch/ppc to arch/powerpc.

This patch also adds ibm405ep_fixup_clocks() to support
405EP CPUs from the boot wrapper.
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Remove some unneeded braces and make a busy loop more obvious.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Currently we have some limitations in the 4xx PCIe driver and can't
support all possible PCIe busses. But the current limits in the
dts file are quite low (only 16 busses per RC). This patch increases
the number to 64 per RC.
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This adds PCI entry to PowerPC 440GRx Rainier DTS.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Recent DTC versions disallow certain special characters in full paths without
being quoted with {}.  That however breaks compatibility with older DTC
versions.  Work around this by renaming the CPU nodes for the 4xx files to a
generic node name, and specify the processor type in the model property of the
CPU node.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

The recent changes from Benjamin Herrenschmidt to the ibm_newemac now
make it possible to support other 4xx variants by just defining the
correct properties in the device tree. In this case of the 405EX we
need to define "has-mdio" in the RGMII node and "has-inverted-stacr-oc"
and "has-new-stacr-staopc" in the EMAC node same as on the 440EPx.
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Update the Rainier wrapper for the libfdt merge and add the pci flags to the
platform file.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

PowerPC 440Epx/GRx Sequoia/Rainier updates for 2.6.25
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This adds PCI entry to PowerPC 440EPx Sequoia DTS.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

PowerPC 440GRx Rainier DTS.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>