Make default flow control only have *sending* of flow control packets
enabled, and fix to disable / enable flow control correctly. Set flow
control defaults to disable receiving flow control from the link
partner, to fix the transmit fifo overlow errata
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJohn Ronciak <john.ronciak@intel.com>

Removed duplicate code.  Create ixgb_set_speed_duplex function to contain
duplicate code.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJohn Ronciak <john.ronciak@intel.com>

Fix rare early completion when using TSO.  This essentially is the
e1000 fix, with code that was mostly already written. Another skb frag
was also needed.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJohn Ronciak <john.ronciak@intel.com>

Call pci_map_single() with the actual size of the receive
buffers, not 0 (which skb->len is initialized to by dev_alloc_skb()).
Signed-off-by: NErling A. Jacobsen <linuxcub@email.dk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Dear Jeff

axnet_cs: bug fix multicast code (support older ax88190 chipset)

Signed-off-by: komurojun-mbn@nifty.com

Best Regards
Komuro
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The driver will get stuck (permanent transmit timeout), if the transmit
ring size is set too small.  It needs to have enough ring elements to
hold one maximum size transmit.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Skge driver always causes  bad checksums on big-endian.
The checksum in the receive control block was being swapped
when it doesn't need to be.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Need to track impact of this group of changes.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

If the status ring processing can't keep up with the incoming frames,
it is more efficient to have NAPI keep scheduling the poll routine
rather than causing another interrupt.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Logic error in the phy initialization code. Also, turn on wake on lan
bit in status control.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The Dlink DGE-560T uses Yukon2 chipset so it needs sky2 driver; and
the DGE-530T uses Yukon1 so it uses skge driver.

Bug: http://bugzilla.kernel.org/show_bug.cgi?id=6544Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

If both ports are receiving on the SysKonnect dual port cards,
then it appears the bus interface unit can give an interrupt status
for frame before DMA has completed.  This leads to bogus frames
and general confusion. This is why receive checksumming is also
messed up on dual port cards.

A workaround for the out of order receive problem is to eliminating
split transactions on PCI-X.

This version is based of the current linux-2.6.git including earlier
patch to disable dual ports.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Revert previous patch with subject "change mdelay to msleep and remove
from ISR path".  This patch seems to have caused bigger problems than
it solved, and it didn't solve much of a problem to begin with...

Discussion about backing-out this patch can be found here:

	http://marc.theaimsgroup.com/?l=linux-netdev&m=114321570402396&w=2

The git commit associated w/ the original patch is:

	6ba98d31

Signed-off-by: John W. Linville <linville@tuxdriver.com
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Revert ebf34c9b.  Maybe.  Due to crashes
at shutdown - see http://bugzilla.kernel.org/show_bug.cgi?id=6568.

Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

I still need this hack to work around the fact that softmac doesn't
attempt to associate when we bring the device up...
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Needed for interaction with the nommu code in x86-64 which
will return bad_dma_address if the address exceeds dma_mask.

Cc: netdev@vger.kernel.org
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

When both ports are receiving simultaneously, the receive logic gets confused
and may pass up a packet before it is full. This causes hangs, and IP will see
lots of garbage packets. There is even the potential for data corruption if
a later arriving packet DMA's into freed memory.

It looks like a hardware bug because status arrives for a packet but no
data is there. Until this bug is worked out, block the user from bringing
up both ports at once.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Needed for interaction with the nommu code in x86-64 which
will return bad_dma_address if the address exceeds dma_mask.

Cc: netdev@vger.kernel.org
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

three gigabit ports, but some enp2611 models only have two ports
(and only one onboard PM3386.)  The current driver assumes there
are always three ports and so it doesn't work on the two-port
version of the board at all.

This patch adds a bit of logic to the enp2611 driver to limit the
number of ports to 2 if the second PM3386 isn't detected.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

On alpha:

drivers/net/dl2k.c: In function `rio_free_tx':
drivers/net/dl2k.c:768: error: `DMA_48BIT_MASK' undeclared (first use in this function)
drivers/net/dl2k.c:768: error: (Each undeclared identifier is reported only once
drivers/net/dl2k.c:768: error: for each function it appears in.)
drivers/net/dl2k.c: In function `receive_packet':
drivers/net/dl2k.c:896: error: `DMA_48BIT_MASK' undeclared (first use in this function)
drivers/net/dl2k.c: In function `rio_close':
drivers/net/dl2k.c:1803: error: `DMA_48BIT_MASK' undeclared (first use in this function)

Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Even with fiber cards ethtool reports that the connected port is TP,
the patch fix this.
Signed-off-by: NKarsten Keil <kkeil@suse.de>
Acked-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

661FX7MI-S motherboard which uses the SiS 661FX chipset.  The patch adds
an entry to mii_chip_info for the transceiver.

The PHY ids were found using the sis900_c_122.diff patch from
http://brownhat.org/sis900.html but that patch didn't solve the problem,
because the PHY at address 1 was already being chosen.

Without my patch, when bursts of packets arrive from other hosts on a
LAN, the interface dropped one roughly 10% of the time, causing
retransmits.  There were fifth second pauses in refresh of large xterms,
and it made Netrek suck.  I can provide further test data.

Workaround in lieu of patch is to use mii-tool to advertise
100baseTx-HD, then force renegotiation.

I wasn't able to identify the actual transceiver, so the description
field is a guess.

This patch is similar to Artur Skawina's patch:
http://marc.theaimsgroup.com/?l=linux-netdev&m=114297516729079&w=2

I'm not sure, but I wonder if it means the default behaviour should be
changed, so as to better handle future transceivers.

Diff is against 2.6.16.13.
Signed-off-by: NJames Cameron <james.cameron@hp.com>
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Typo will be harder with this one.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

make sure phy_map entries whose PHY address is masked are initialized
to NULL, given that other code (such as mdiobus_unregister for
instance) assumes that non-NULL phy_map entries are allocated
phy_devices
Signed-off-by: NHerbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Bringing down a port also masks off the status and other IRQ's
needed for device to function due to missing paren's.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

tg3_run_loopback doesn't check that dev_alloc_skb() returns anything
useful.

Even if dev_alloc_skb() fails to return an skb to us we'll happily go
on and assume it did, so we risk dereferencing a NULL pointer.  Much
better to fail gracefully by returning -ENOMEM than crashing here.
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since sir_kthread.c pretty much duplicates the workqueue
functionality, we'd better switch.  The SIR fsm has been merged into
sir_dev.c and thus sir_kthread.c is deleted.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NSamuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Minimal PNP hotplug support for the smsc-ircc2 driver.  A modular
driver will be modprobed via hotplug, but still bypasses driver model
probing.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NSamuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A newer board revision changed the type of ethernet phy.
Moreover, this generalizes the way that a phy gets switched
into fiber mode when autodetection is not available.
Signed-off-by: NJens Osterkamp <Jens.Osterkamp@de.ibm.com>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

We found a new chip setting that we need in order
to make the driver work more reliable.
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

    Ensure that 8-bit mode is selected for the on-board Realtek RTL8019AS chip
on Toshiba RBHMA4x00, get rid of the duplicate #ifdef's when setting
ei_status.word16.
    The chip's datasheet says that the PSTOP register shouldn't exceed 0x60 in
8-bit mode -- ensure this too.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

since the au1000 driver already selects the CRC32 routines, simply replace
the internal ether_crc() implementation with the semantically equivalent
one from <linux/crc32.h>
Signed-off-by: NHerbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Update version number, to track changes.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

The newest Yukon Ultra chipset's require more special tweaks.
They seem to be like the Yukon XL chipsets. This code is transliterated
from the latest SysKonnect driver; I don't have any Ultra hardware.
Signed-off-by: NStephe Hemminger <shemminger@osdl.org>
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Need to make sure interrupt is not racing with unregister of
network device.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

It is more efficient not to write the status ring from the
processor and just read the active portion.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Need to make the edge-triggered workaround timer faster to get marginally
better peformance. The test_and_set_bit in schedule_prep() acts as a barrier
already. Make it a module parameter so that laptops who are concerned
about power can set it to 0; and user's stuck with broken BIOS's
can turn the driver into pure polling.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Gcc isn't smart enough to know that it can do a modulo
operation with power of 2 constant by doing a mask.
So add macro to do it for us.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Mask for transmit ring status was picking up bits from the
unused sync ring.  They were always zero, so far...
Also, make sure to remind self not to make tx ring too big.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

The status interrupt flag should be cleared before processing,
not afterwards to avoid race. Need to process in poll routine
even if no new interrupt status. This is a normal occurrence when
more than 64 frames (NAPI weight) are processed in one poll routine.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>