Make default flow control only have *sending* of flow control packets
enabled, and fix to disable / enable flow control correctly. Set flow
control defaults to disable receiving flow control from the link
partner, to fix the transmit fifo overlow errata
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJohn Ronciak <john.ronciak@intel.com>

Removed duplicate code.  Create ixgb_set_speed_duplex function to contain
duplicate code.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJohn Ronciak <john.ronciak@intel.com>

Fix rare early completion when using TSO.  This essentially is the
e1000 fix, with code that was mostly already written. Another skb frag
was also needed.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJohn Ronciak <john.ronciak@intel.com>

Call pci_map_single() with the actual size of the receive
buffers, not 0 (which skb->len is initialized to by dev_alloc_skb()).
Signed-off-by: NErling A. Jacobsen <linuxcub@email.dk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Dear Jeff

axnet_cs: bug fix multicast code (support older ax88190 chipset)

Signed-off-by: komurojun-mbn@nifty.com

Best Regards
Komuro
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The driver will get stuck (permanent transmit timeout), if the transmit
ring size is set too small.  It needs to have enough ring elements to
hold one maximum size transmit.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Skge driver always causes  bad checksums on big-endian.
The checksum in the receive control block was being swapped
when it doesn't need to be.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Need to track impact of this group of changes.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

If the status ring processing can't keep up with the incoming frames,
it is more efficient to have NAPI keep scheduling the poll routine
rather than causing another interrupt.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Logic error in the phy initialization code. Also, turn on wake on lan
bit in status control.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The Dlink DGE-560T uses Yukon2 chipset so it needs sky2 driver; and
the DGE-530T uses Yukon1 so it uses skge driver.

Bug: http://bugzilla.kernel.org/show_bug.cgi?id=6544Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

If both ports are receiving on the SysKonnect dual port cards,
then it appears the bus interface unit can give an interrupt status
for frame before DMA has completed.  This leads to bogus frames
and general confusion. This is why receive checksumming is also
messed up on dual port cards.

A workaround for the out of order receive problem is to eliminating
split transactions on PCI-X.

This version is based of the current linux-2.6.git including earlier
patch to disable dual ports.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Revert previous patch with subject "change mdelay to msleep and remove
from ISR path".  This patch seems to have caused bigger problems than
it solved, and it didn't solve much of a problem to begin with...

Discussion about backing-out this patch can be found here:

	http://marc.theaimsgroup.com/?l=linux-netdev&m=114321570402396&w=2

The git commit associated w/ the original patch is:

	6ba98d31

Signed-off-by: John W. Linville <linville@tuxdriver.com
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Revert ebf34c9b.  Maybe.  Due to crashes
at shutdown - see http://bugzilla.kernel.org/show_bug.cgi?id=6568.

Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Patch from Pavel Pisa

There has been problems that for some paths that clock are not stopped
during new command programming and initiation. Result is issuing
of incorrect command to the card. Some other problems are cleaned too.
Noisy report of known ERRATUM #4 has been suppressed.
Signed-off-by: NPavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

If we post a list of length 256 exactly, nreq in doorbell gets set to
256 which is wrong: it should be encoded by 0.  This is because we
only zero it out on the next WR, which may not be there.  The solution
is to ring the doorbell after posting a WQE, not before posting the
next one.
Signed-off-by: NMichael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

In ib_umem_release_on_close(), if the kmalloc() fails, then a
reference to current->mm will be leaked.  Fix this by adding a mmput()
instead of just returning on kmalloc() failure.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Re-enable posted writes for status FIFO.

Besides bringing back a very minor bandwidth tweak from Linux 2.6.15.x
and older, this also fixes an interoperability regression since 2.6.16:

   http://bugzilla.kernel.org/show_bug.cgi?id=6356
   (sbp2: scsi_add_device failed. IEEE1394 HD is not working anymore.)
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Tested-by: NVanei Heidemann <linux@javanei.com.br>
Tested-by: Martin Putzlocher <mputzi@gmx.de> (chip type unconfirmed)
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

In case the blacklist with workarounds for device bugs yields a false
positive, the module load parameter can now also be used as an override
instead of an addition to the blacklist.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Apple decided to copy some USB stupidity over to FireWire.

The sector number returned by iPods from read_capacity is one too many.
This may cause I/O errors, especially if the kernel is configured for EFI
partition support. We use the same workaround as usb-storage but have to
check for different model IDs.

	http://marc.theaimsgroup.com/?t=114233262300001
	https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=187409

Acknowledgements:
  Diagnosis and therapy by Mathieu Chouquet-Stringer <ml2news@free.fr>,
  additional data about affected and unaffected Apple hardware from
  Vladimir Kotal, Sander De Graaf, Bryan Olmstead and Hugh Dixon.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Grand unification of the three types of workarounds we have so far.

The "skip mode page 8" workaround is now limited to devices which
pretend to be of TYPE_DISK instead of TYPE_RBC. This workaround is no
longer enabled for Initio bridges.

Patch update in anticipation of more workarounds:
 - Add module parameter "workarounds".
 - Deprecate parameter "force_inquiry_hack".
 - Compose the blacklist of a compound type for better readability and
   extensibility.
 - Remove a now unused #define.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

I still need this hack to work around the fact that softmac doesn't
attempt to associate when we bring the device up...
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When flushing out queued commands after a successful device reset,
make sure that SRP completes the right commands, instead of calling
scsi_done on the command passed into the device reset handler over and
over.
Signed-off-by: NIshai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

If a reconnection attempt fails, then SRP does two scsi_host_put()s.
This is a historical relic from an earlier version of the driver that
took a reference on the scsi_host before trying to reconnect, so get
rid of the extra scsi_host_put().
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Sending a DREQ may fail, for example because the remote target has
already broken the connection.  If so, then SRP should not wait for
the disconnection to complete, because it never will.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Setting fw_cmd_doorbell allows FW command to be queued using posted
writes instead of requiring polling on a "go" bit, so it should be a
performance boost.  However, the option causes problems with at least
some device/firmware combinations, so set the default to 0 until we
understand what's going on better.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This fixes two problems triggered by the MMC stack updating clocks:

 - SPI masters driver should accept a max clock speed of zero; that's one
   convention for marking idle devices.  (Presumably that helps controllers
   that don't autogate clocks to "off" when not in use.)

 - There are more than 1000 nanoseconds per millisecond; setting the clock
   down to 125 KHz now works properly.

Showing once again that Zero (http://en.wikipedia.org/wiki/Zero) is still
an inexhaustible number of bugs.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix two outstanding issues with the pxa2xx_spi driver:

1) Bad cast in the function u32_writer. Thanks to Henrik Bechmann
2) Adds support for per transfer changes to speed and bits per word
Signed-off-by: NStephen Street <stephen@streetfiresound.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We need to be able to have a "SPI bus 0" matching chip numbering; but
that number was wrongly used to flag dynamic allocation of a bus number.

This patch resolves that issue; now negative numbers trigger dynamic alloc.

It also updates the how-to-write-a-controller-driver overview to mention
this stuff.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add spi_device hook for LSB-first word encoding, and update all the
(in-tree) controller drivers to reject such devices.  Eventually,
some controller drivers will be updated to support lsb-first encodings
on the wire; no current drivers need this.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Renamed bitbang_transfer_setup to follow convention of other exported symbols
from spi-bitbang.  Exported spi_bitbang_setup_transfer to allow users of
spi-bitbang to use the function in their own setup_transfer.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Make sure that spi_write_then_read() can always handle at least 32 bytes
of transfer (total, both directions), minimizing one portability issue.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This driver turns a PXA2xx synchronous serial port (SSP) into a SPI master
controller (see Documentation/spi/spi_summary).  The driver has the following
features:

- Support for any PXA2xx SSP
- SSP PIO and SSP DMA data transfers.
- External and Internal (SSPFRM) chip selects.
- Per slave device (chip) configuration.
- Full suspend, freeze, resume support.
Signed-off-by: NStephen Street <stephen@streetfiresound.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some protocols (like one for some bitmap displays) require different clock
speed or word size settings for each transfer in an SPI message. This adds
those parameters to struct spi_transfer.  They are to be used when they are
nonzero; otherwise the defaults from spi_device are to be used.

The patch also adds a setup_transfer callback to spi_bitbang, uses it for
messages that use those overrides, and implements it so that the pure
bitbanging code can help resolve any questions about how it should work.
Signed-off-by: NImre Deak <imre.deak@nokia.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Needed for interaction with the nommu code in x86-64 which
will return bad_dma_address if the address exceeds dma_mask.

Cc: netdev@vger.kernel.org
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Patch from Andrew Victor

The serial_core already manages the power state of the UARTs, and
therefore it shouldn't suspend a UART which was previously suspended.

This patch modifies serial_core only call the UART-specific
power-management function if the PM state is actually changing.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

If the s3c2410 watchdog timer is not enabled by
the driver at startup, ensure that it is stopped
in-case the boot process has enabled it.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
Signed-off-by: NAndrew Morton <akpm@osdl.org>

Temporary remove support for ICH6 + ICH7. In these newer TCO's
the watchdog timer has changed: the TCO_TMR register is not at
the TCOBASE+0x1 offset, but changed it's place to TCOBASE+0x12
and became 10 bit long [0:9]. (Kernel BUG 6031).

ICH6 + ICH7 support will be added in a new driver. Code is
under test.
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
Signed-off-by: NAndrew Morton <akpm@osdl.org>

Fix printk output.

sc1200wdt: build 20020303<3>sc1200wdt: io parameter must be specified
Signed-off-by: NDave Jones <davej@redhat.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
Signed-off-by: NAndrew Morton <akpm@osdl.org>

When both ports are receiving simultaneously, the receive logic gets confused
and may pass up a packet before it is full. This causes hangs, and IP will see
lots of garbage packets. There is even the potential for data corruption if
a later arriving packet DMA's into freed memory.

It looks like a hardware bug because status arrives for a packet but no
data is there. Until this bug is worked out, block the user from bringing
up both ports at once.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>