bnx2x still appears as a Broadcom driver even though the devices it
utilizes belong to Qlogic for more than a year.

This patch changes the various headers and the device strings to indicate
the correct ownership of the device.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CC: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

During an error flow when trying to access the nvram the driver doesn't
release the hw lock it acquired.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since driver statistics flow access MACs and those might reset during
link re-configurations, when we're about to change link properties we
have to make sure that statistics are not operational.
Statisics would be re-enabled [i.e., gathering of statistics would
re-commence] once physical link is achieved again.

Since driver employs a link-flap avoidance scheme, there are scenarios
where driver will receive no indication that the new link is up, and
as a result the statistics would not be re-enabled.

Preventing LFA from working in such cases would guarantee that we'll
always receive such indications and thus will fix statistics gathering.
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ethtool shows KR supported/advertised speeds incorrectly as baseT
in cases the board is in fact KR-base.
Signed-off-by: NYaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some feature changes, driver employes an inner-reload flow where it
resets the function and re-configures it with the new required set of
parameters.

Such a flow proves fatal to any VF since those were not intended to be used
while HW is being reset underneath, causing them [at best] to lose all
connectivity.

This changes driver behavior to fail all configuration changes [e.g., mtu
change] requested of the driver in case VFs are active.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the built-in function instead of memset.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch extends the set/get_rxfh ethtool-options for getting or
setting the RSS hash function.

It modifies drivers implementation of set/get_rxfh accordingly.

This change also delegates the responsibility of checking whether a
modification to a certain RX flow hash parameter is supported to the
driver implementation of set_rxfh.

User-kernel API is done through the new hfunc bitmask field in the
ethtool_rxfh struct. A bit set in the hfunc field is corresponding to an
index in the new string-set ETH_SS_RSS_HASH_FUNCS.

Got approval from most of the relevant driver maintainers that their
driver is using Toeplitz, and for the few that didn't answered, also
assumed it is Toeplitz.

Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Cc: Prashant Sreedharan <prashant@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: Matthew Vick <matthew.vick@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Mitch Williams <mitch.a.williams@intel.com>
Cc: Amir Vadai <amirv@mellanox.com>
Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com>
Cc: Shradha Shah <sshah@solarflare.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: "VMware, Inc." <pv-drivers@vmware.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: NEyal Perry <eyalpe@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rearrange macros to query for storage-only modes in different MF environment.
Improves the readibility and maintainability of the code. E.g.:
	-	if (IS_MF_STORAGE_SD(bp) || IS_MF_FCOE_AFEX(bp))
	+	if (IS_MF_STORAGE_ONLY(bp))

In addition, this removes the need for bnx2x_is_valid_ether_addr().
Signed-off-by: NDmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds a PHC to the bnx2x driver. Driver supports timestamping send/receive
PTP packets, as well as adjusting the on-chip clock.

The driver has been tested with linuxptp project.
Signed-off-by: NMichal Kalderon <Michal.Kalderon@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow set_settings() to complete succesfully even if link is
not estabilished and port type isn't known yet.
Signed-off-by: NYaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: NDmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Until now VFs were oblvious to the actual configured link parameters.
This patch does 2 things:

  1. It enables a PF to inform its VF using the bulletin board of the link
     configured, and allows the VF to present that information.

  2. It adds support of `ndo_set_vf_link_state', allowing the hypervisor
     to set the VF link state.
Signed-off-by: NDmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ETHTOOL_{G,S}RXFHINDIR and ETHTOOL_{G,S}RSSH should work for drivers
regardless of whether they expose the hash key, unless you try to
set a hash key for a driver that doesn't expose it.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The bnx2x development team has transferred from Broadcom to Qlogic.
This patch updates some obsolete email addresses to usable ones.
The bnx2x files contain headers with legal information from
Broadcom. Qlogic Legal depratment is taking their time coming up
with their own legal info. So this patch only updates contact
information. I will follow up with a patch for the headers once I
have the required info.
Signed-off-by: NAriel Elior <ariel.elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

net: get rid of SET_ETHTOOL_OPS

Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.

Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
-       SET_ETHTOOL_OPS(dev, ops);
+       dev->ethtool_ops = ops;

Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: NDave Miller <davem@davemloft.net>
Signed-off-by: NWilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VFs are currently showing port statistics, although they can't really access
those - thus all such statistics will always show a value of 0.

This patch removes said statistics from the VF's view as to not confuse the
user.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When user tried to change generic options using "ethtool -s" command, while SFP
module is plugged out or during module detection, the command would have failed
with "Unsupported port type" message. The fix is to ignore the port option in
case it's same as the current port configuration.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There's a known issue that using `ethtool -e' flips the endianity of the
written data, i.e., using `ethtool -E' to dump eeprom image and than using
`ethtool -e' to re-write that same image will result in an image where
the data has the opposite endianity.
Sadly, this cannot be fixed as there are already various tools deployed
based on the endianity of the eeprom read/write.
Instead, a comment is added to the code to help explain why this is un-fixable.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As part of a register dump, the interface pretends to have the identity
of other interfaces of the same physical device in order to perform
HW configuration for them - specifically, it needs to prevent attentions
from generating on those functions as the register dump accesses registers
in common blocks which whose reading might generate an attention.

However, such pretension is unsafe - unlike other flows in which the driver
uses pretend, during register dump there is no guarantee no other HW access
will take place (by other flows). If such access will take place, the HW will
be accessed by the wrong interface, and leave both functions in an incorrect
state.

This patch removes all pretensions from the register dump flow. Instead, it
changes initial configuration of attentions such that no fatal attention will
be generated for other functions as a result of the register dump
(notice however, a debug print claiming an attention from other functions IS
possible during the register dump)
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When running ethtool on VF interfaces, returning values should indicate
that the interface does not support self-test or register dump.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit 3fb43eb2 ("bnx2x: Change to D3hot only on removal") nvram
is accessible whenever the driver is loaded - Thus it is possible to
test it during self-test even if the interface is down
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the already existing pm_cap variable in struct pci_dev for
determining the power management offset.  This saves the driver from
having to keep track of an extra variable.
Signed-off-by: NJon Mason <jdmason@kudzu.us>
Cc: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In this patch capabilities are added to the Vf driver to request
multiple queues over the VF PF channel, and the logic for requesting
rss configuration for said queues.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilong Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnx2x did not set dump->version in its .get_dump_flag() method.
Let's set it to BNX2X_DUMP_VERSION. It's not a particularly nice
number (0x50acff01 currently), but at least it's something
deterministic.

dump->flag should report the value previously set using ethtool -W.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnx2x interprets the dump flag as an index of a register preset.
It is important to validate the index to avoid out of bounds
memory accesses.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no need to initialize the dump data with zeros.
data is allocated with vzalloc, so it's already zero-filled.

More importantly, the memset is harmful, because dump->len (the length
requested by userspace) can be bigger than the allocated buffer (whose
size is determined by asking the driver's .get_dump_flag method).
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch solves several sparse issues as well as an unneeded semicolon
found via coccinelle.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If PCIe supports PM capabilities, bnx2x will always claim eeprom is accessible
as PCI_D0 is zero.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch correct various typos, fix comments conventions and
adds/removes a few comments.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes unnecessary blank lines and adds a few where such are needed
(between variable declarations and code)
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This changes the PCI power management scheme of the bnx2x driver to be similar
to those of most network drivers - the driver will now changes the power state
into D3hot whenever the driver will be removed, instead of whenever an
interface is unloaded.

This change enables the driver to access its eeprom via ethtool callbacks
even when interfaces are unloaded (such access requires the function to be
in D0active).
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In Multi-function mode, all functions should be able to utilize said function;
There's no reason why only the link owner should be able to do so.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Utilize ethtool's callback `get_priv_flags' - shed more light on the
feasibility of devices as storage interfaces.

CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Acked-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit d2d2d87d
("bnx2x: allow nvram test to run when device is down").

Since it makes access to the device in D3 state possible.
More work is required to make sure device is not set to D3
during ifdown. Until this is done the nvram-test should simply
exit if device is down like it did before.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, when link is configured to auto-negotiate the flow control,
disabling RX/TX pause via ethtool doesn't work.

This fixes the behaviour, advertising asymmetric pause in case either one
is exclusively enabled.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

a. Common tree of `dir` structures.
b. Multi-port devices structures.

CC: Francious Romieu <romieu@fz.zoreil.com>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CC: Francious Romieu <romieu@fz.zoreil.com>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CC: Francious Romieu <romieu@fz.zoreil.com>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

introduce a procedure to read in u32 granularity.

CC: Francious Romieu <romieu@fz.zoreil.com>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>