This adds support to a new copper phy.
Signed-off-by: NYaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnx2x still appears as a Broadcom driver even though the devices it
utilizes belong to Qlogic for more than a year.

This patch changes the various headers and the device strings to indicate
the correct ownership of the device.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This moves bnx2x into using 7.12.30 FW. Said firmware fixes the following:

 - Packets from a VF with pvid configured which were sent with a
   different vlan were transmitted instead of being discarded.

 - FCoE traffic might not recover after a failue while there's traffic
   to another function.

In addition, this FW opens the door for the driver to implement several
new features; Specifically, this enhances the device's support for
encapsulated packets and will allow vxlan/geneve offloads to be added in
the future, as well as vlan filtering offload.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add debugfs entry 'use_backdoor' to enable backdoor access to read sge
context. By default, we read sge context's via firmware. In case of FW
issues, one can enable backdoor access via debugfs to dump sge context
for debugging purpose.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Separate functions for inserting individual and promisc filters; explicit
 fallback logic in efx_ef10_filter_sync_rx_mode(), in order not to overload
 the 'promisc' flag as also meaning "fall back to promisc".
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the workaround to support cascaded multicast filters ("workaround_26807") is
enabled, the broadcast filter and individual multicast filters are not inserted
when in promiscuous or allmulti mode.

There is a race while inserting and removing filters when entering and leaving
promiscuous mode.  When changing promiscuous state with cascaded multicast
filters, the old multicast filters are removed before inserting the new filters
to avoid duplicating packets; this can lead to dropped packets until all
filters have been inserted.

The efx_nic:mc_promisc flag is added to record the presence of a multicast
promiscuous filter; this gives a simple way to tell if the promiscuous state is
changing.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change is only re-factoring; there are no changes to functionality
 except for a slight elaboration of an error message (on mismatch filter
 insertion failure).
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a function is in promiscuous mode and another function has a broadcast or
 multicast filter inserted, the function in promiscuous mode won't see that
 broadcast or multicast traffic.
Most notably this breaks broadcast, which means ARP doesn't work. Less
 show-stoppingly, a function listening on a multicast address that's also in
 promiscuous mode will not see that multicast traffic if another function is
 also listening on that multicast address.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When enabling the workaround for cascaded multicast filters, the MC
 can reset other functions if they have already inserted filters.
 In that case, the workaround has been enabled, but print an info
 message in the log recording that other functions had to be reset.

As other functions were reset, the MC will have incremented its boot
 count, so also increment the warm_boot_count on the function which
 enabled the workaround, as that function won't have received an MC
 reboot event and does not need to reset.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The initial use of this will be to check a flag reporting if an FLR was
performed on other functions when enabling cascaded multicast filters.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

GET_WORKAROUNDS was only introduced in May 2014, not all firmware
 will have it.  So call sites need to handle ENOSYS.
In this case we're probing the bug26807 workaround, which is not
 implemented in any firmware that doesn't have GET_WORKAROUNDS.
 So interpret ENOSYS as 'false'.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After creating event queue 0, check to see if the workaround is enabled,
 and enable it if necessary.  This will be called during PCI probe and
 also when coming back up after a reset.  The nic_data->workaround_26807
 will be used in the future to control the filter insertion behaviour
 based on this workaround.

Only the primary PF can enable this workaround, so tolerate an EPERM
 error and continue.  Otherwise, if any step in the checking and enabling
 of the workaround fails, the event queue must be removed.

We check that workaround is implemented before trying to enable it,
 and store the current workaround setting before trying to change it.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit 898b2970 ("mvneta: implement SGMII-based in-band link state
signaling") implemented the link parameters auto-negotiation unconditionally.
Unfortunately it appears that some HW that implements SGMII protocol,
doesn't generate the inband status, so it is not possible to auto-negotiate
anything with such HW.

This patch enables the auto-negotiation only if explicitly requested with
the 'managed' DT property.

This patch fixes the following regression:
https://lkml.org/lkml/2015/7/8/865Signed-off-by: NStas Sergeev <stsp@users.sourceforge.net>

CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
CC: netdev@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fixed_phy_register() currently hardcodes the fixed PHY link to 1, and
expects to find a "speed" parameter to provide correct information
towards the fixed PHY consumer.

In a subsequent change, where we allow "managed" (e.g: (RS)GMII in-band
status auto-negotiation) fixed PHYs, none of these parameters can be
provided since they will be auto-negotiated, hence, we just provide a
zero-initialized fixed_phy_status to fixed_phy_register() which makes it
fail when we call fixed_phy_update_regs() since status.speed = 0 which
makes us hit the "default" label and error out.

Without this change, we would also see potentially inconsistent
speed/duplex parameters for fixed PHYs when the link is DOWN.

CC: netdev@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: NStas Sergeev <stsp@users.sourceforge.net>
[florian: add more background to why this is correct and desirable]
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SF2 driver currently overrides speed settings for its port
configured using a fixed PHY, this is both unnecessary and incorrect,
because we keep feedback to the hardware parameters that we read from
the PHY device, which in the case of a fixed PHY cannot possibly change
speed.

This is a required change to allow the fixed PHY code to allow
registering a PHY with a link configured as DOWN by default and avoid
some sort of circular dependency where we require the link_update
callback to run to program the hardware, and we then utilize the fixed
PHY parameters to program the hardware with the same settings.

Fixes: 246d7f77 ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This gets rid of all OVS specific VXLAN code in the receive and
transmit path by using a VXLAN net_device to represent the vport.
Only a small shim layer remains which takes care of handling the
VXLAN specific OVS Netlink configuration.

Unexports vxlan_sock_add(), vxlan_sock_release(), vxlan_xmit_skb()
since they are no longer needed.
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This factors out the device configuration out of the RTNL newlink
API which allows for in-kernel creation of VXLAN net_devices.
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This add the ability to select a routing table based on the tunnel
id which allows to maintain separate routing tables for each virtual
tunnel network.

ip rule add from all tunnel-id 100 lookup 100
ip rule add from all tunnel-id 200 lookup 200

A new static key controls the collection of metadata at tunnel level
upon demand.
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This introduces a new IP tunnel lightweight tunnel type which allows
to specify IP tunnel instructions per route. Only IPv4 is supported
at this point.
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allows putting a VXLAN device into a new flow-based mode in which
skbs with a ip_tunnel_info dst metadata attached will be encapsulated
according to the instructions stored in there with the VXLAN device
defaults taken into consideration.

Similar on the receive side, if the VXLAN_F_COLLECT_METADATA flag is
set, the packet processing will populate a ip_tunnel_info struct for
each packet received and attach it to the skb using the new metadata
dst.  The metadata structure will contain the outer header and tunnel
header fields which have been stripped off. Layers further up in the
stack such as routing, tc or netfitler can later match on these fields
and perform forwarding. It is the responsibility of upper layers to
ensure that the flag is set if the metadata is needed. The flag limits
the additional cost of metadata collecting based on demand.

This prepares the VXLAN device to be steered by the routing and other
subsystems which allows to support encapsulation for a large number
of tunnel endpoints and tunnel ids through a single net_device which
improves the scalability.

It also allows for OVS to leverage this mode which in turn allows for
the removal of the OVS specific VXLAN code.

Because the skb is currently scrubed in vxlan_rcv(), the attachment of
the new dst metadata is postponed until after scrubing which requires
the temporary addition of a new member to vxlan_metadata. This member
is removed again in a later commit after the indirect VXLAN receive API
has been removed.
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added the USB IDs 0x413c:0x81b1 for the "Dell Wireless 5809e Gobi(TM) 4G
LTE Mobile Broadband Card", a Dell-branded Sierra Wireless EM7305 LTE
card in M.2 form factor, used eg. in Dell's Latitude E7540 Notebook
series.
Signed-off-by: NPieter Hollants <pieter@hollants.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAnish Bhatt <anish@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAnish Bhatt <anish@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since finally DCB traffic management is still handled by firmware,
allow firmware to be fully programmed and queried even in host
managed state for the cases where this was previously rejected.
Signed-off-by: NAnish Bhatt <anish@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This keeps app format passed to firmware the same irrespective
of DCBx version in use.
Signed-off-by: NAnish Bhatt <anish@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

__vxlan_find_mac invokes ether_addr_equal on the eth_addr field,
which triggers unaligned access messages, so rearrange vxlan_fdb
to avoid this in the most non-intrusive way.
Signed-off-by: NSowmini Varadhan <sowmini.varadhan@oracle.com>
Reviewed-by: NJiri Pirko <jiri@resnulli.us>
Reviewed-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Teranetics TN2020 is compliant with IEEE 802.3an 10 Gigabit.
Signed-off-by: NShaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that we have reworked the way we perform the PHY initialization, we
no longer need to differentiate between init time vs. non-init time
calls, just use a dev_info_once() print to print the PHY type.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We are currently doing a full PHY initialization and even starting the
pHY state machine during bcmgenet_mii_init() which is executed in the
driver's probe function. This is convenient to determine whether we can
attach to a proper PHY device but comes at the expense of spending up to
10ms per MDIO transactions (to reach the waitqueue timeout), which slows
things down.

This also creates a sitaution where we end-up attaching twice to the
PHY, which is not quite correct either.

Fix this by moving bcmgenet_mii_probe() into bcmgenet_open() and update
its error path accordingly.

Avoid printing the message "attached PHY at address 1 [...]" every time
we bring up/down the interface and remove this print since it duplicates
what the PHY driver already does for us.

Fixes: 1c1008c7 ("net: bcmgenet: add main driver file")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Our internal GPHY might be powered off before we attempt scanning the
MDIO bus and bind a driver to it. The way we are currently determining
whether a PHY is internal or not is done *after* we have successfully
matched its driver. If the PHY is powered down, it will not respond to
the MDIO bus, so we will not be able to bind a driver to it.

Our Device Tree for GENET interfaces specifies a "phy-mode" value:
"internal" which tells if this internal uses an internal PHY or not.

If of_get_phy_mode() fails to parse the 'phy-mode' property, do an
additional manual lookup, and if we find "internal" set the
corresponding internal variable accordingly.

Replace all uses of phy_is_internal() with a check against
priv->internal_phy to avoid having to rely on whether or not
priv->phydev is set correctly.

Fixes: 1c1008c7 ("net: bcmgenet: add main driver file")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We are currently disabling the GPHY interface during bcmgenet_close(),
and attempting to power it back on during bcmgenet_open(). This works
fine for the first time, because we called bcmgenet_mii_config() which
took care of enabling the interface, however, bcmgenet_power_up() really
needs to power on the GPHY for correctness.

This will be particularly important as we want to move
bcmgenet_mii_probe() down to bcmgenet_open() to avoid seeing the "PHY
already attached" message.

Fixes: a642c4f7 ("net: bcmgenet: power up and down integrated GPHY when unused")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bcmgenet_open()'s error path call free_irq() with a dev_id argument
different from the one we used to call request_irq() with, this will
make us trip over the warning in kernel/irq/manage.c:__free_irq()

Fixes: 1c1008c7 ("net: bcmgenet: add main driver file")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We are currently issuing multiple PHY resets during a suspend/resume,
first during bcmgenet_power_up() which does a hardware reset, then a
software reset by calling bcmgenet_mii_reset(). This is both unnecessary
and can take as long as 10ms per MDIO transactions while we re-apply
workarounds because we do not yet have MDIO interrupts enabled.

phy_resume() takes care of re-apply our workarounds in case we need any,
and bcmgenet_power_up() does a PHY hardware reset, all of this is more
than enough to guarantee that the PHY operates correctly.

Fixes: 1c1008c7 ("net: bcmgenet: add main driver file")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By using a few functions from stmmac_platform we can now create
a proper probe function in this driver. By doing so we can drop
the OF match data and simplify the overall driver.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By using a few functions from stmmac_platform we can now create
a proper probe function in this driver. By doing so we can drop
the OF match data and simplify the overall driver.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Export stmmac_probe_config_dt() and stmmac_get_platform_resources()
so they can be used in the dwmac-* drivers themselves. This will
allow us to build more flexible and standalone drivers which just
use stmmac_platform as a library for setup functions.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since stmmac_probe_config_dt() allocates the platform data structure
it is cleaner if it just returned this structure directly. This
function will later be used in the probe function in dwmac-* drivers.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Refactor all code that deals with platform resources into it's
own get function. This function will later be used in the probe
function in dwmac-* drivers.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Refactor code to clearly separate probing non-dt versus dt. In the
non-dt case platform data must be supplied to probe successfully.
For dt the platform data structure is created and match data is
copied into it. Note that support for supplying platform data in
dt from AUXDATA is dropped as no users in mainline does this.

This change will allow dt dwmac-* drivers to call the config_dt()
function from probe to create the needed platform data struct and
retrieve common dt properties.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>