__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLuis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The libertas thin firmware only supports usb devices, but the usb functions have
been kept separate to ease future support for other devices.
Signed-off-by: NLuis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLuis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch contains most of the libertastf driver, just lacking command helper
functions and usb specific functions. Currently, monitor, managed, ap and mesh
interfaces are supported. Even though this driver supports the same hardware as
the "libertas" driver, it uses a different (thin) firmware, that makes it
suitable for a mac80211 driver.
Signed-off-by: NLuis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLuis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ieee80211_get_hdrlen_from_skb internally checks that the skb is long
enough to hold the full header, or it returns 0 if not.  The check in
ath5k does not check this case and assumes it always got the actual
header length which it then checks against the skb->len plus some headroom.

Change to ieee80211_hdrlen which always returns the hdrlen and keep the
existing headroom check.
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Acked-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds another level for debugging host command. This adds an
option to suppress the debug prints for sensitivity and link quality
commands.
Signed-off-by: NEsti Kummer <ester.kummer@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes struct iwl4965_lq_mngr it is not used.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

num_tbs is unsigned so the test doesn't work.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

remove drivers own implementation of radiotap in favor of the generic one
provided by mac80211.

also remove priv->add_radiotap because it is not used any more.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

cleanup the rates structures used by ath5k. instead of separate driver and
mac80211 rate structures we now setup a static ieee80211_rate array and use it
directly. no conversion between two different rate structures has to be done
any more. a lot of unused and confusing junk was deleted.

renamed ath5k_getchannels into ath5k_setup_bands because this is what it does.
rewrote it to copy the bitrates correctly for each band. this is necessary for
running different hardware with the same driver (e.g. 5211 and 5212 based
cards).

add special handling of rates for AR5211 chipsets: it uses different rate codes
for CCK rates (which are actually like the other chips but with a 0xF mask).

setup a hardware code to rate index reverse mapping table for getting the rate
index of received frames.

the rates for control frames which have to be set in
ath5k_hw_write_rate_duration are now in one single array.

drivers/net/wireless/ath5k/ath5k.h:     Changes-licensed-under: ISC
drivers/net/wireless/ath5k/base.c:      Changes-licensed-under: 3-Clause-BSD
drivers/net/wireless/ath5k/base.h:      Changes-licensed-under: 3-Clause-BSD
drivers/net/wireless/ath5k/hw.c:        Changes-licensed-under: ISC
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There were 3 code copy and pastes of reset. Unify the resets and place
in separate function.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is not allowed to use NETDEV_TX_BUSY in tx path anymore.
Signed-off-by: NDaniel Wagner <wagi@monom.org>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This enables draft-802.11s Mesh Point operation.  For that we need mesh
beaconing.  Tested with AR5212/AR5213 PCI card against Zydas and b43 mesh
nodes.
Signed-off-by: NAndrey Yurovsky <andrey@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To use these features, copy the boot2 and firmware images to /lib/firmware and:

echo <boot2_image_name> > /sys/class/net/ethX/lbs_flash_boot2
echo <firmware_image_name> > /sys/class/net/ethX/lbs_flash_fw
Signed-off-by: NBrian Cavagnolo <brian@cozybit.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add locking and non-locking versions of if_usb_prog_firmware to support
programming firmware after and before driver bring-up respectively.  Add more
suitable error codes for firmware programming process.  Add capability checks
for persistent features before attempting to use them.

Based on patches from Brajesh Dave and Priyank Singh.
Signed-off-by: NBrian Cavagnolo <brian@cozybit.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Tx/Rx descriptor flags are common between rtl818x devices, only with
additions for newer chips, thus use same flags in the code.
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fixes kernel BUG at lib/radix-tree.c:473.

Previously the handler was incidentally provided by tmpfs but this was
removed with:

  commit 14fcc23f
  Author: Hugh Dickins <hugh@veritas.com>
  Date:   Mon Jul 28 15:46:19 2008 -0700

    tmpfs: fix kernel BUG in shmem_delete_inode

relying on this behaviour was incorrect in any case and the BUG also
appeared when the device node was on an ext3 filesystem.

v2: override a_ops at open() time rather than mmap() time to minimise
races per AKPM's concerns.
Signed-off-by: NIan Campbell <ijc@hellion.org.uk>
Cc: Jaya Kumar <jayakumar.lkml@gmail.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Johannes Weiner <hannes@saeurebad.de>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Kel Modderman <kel@otaku42.de>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: <stable@kernel.org> [14fcc23f is in 2.6.25.14 and 2.6.26.1]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

On a PowerPC board with ds1374 RTC I'm getting this error while RTC tries
to probe:

rtc-ds1374 0-0068: unable to request IRQ

This happens because I2C probing code (drivers/of/of_i2c.c) is specifying
IRQ0 for 'no irq' case, which is correct.

The driver handles this incorrectly, though. This patch fixes it.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Video/Framebuffer: add fuctional power management support to Blackfin BF54x LQ043 framebuffer driver

Fix bug: does nor properply resume after suspend mem
Fix for PM_SUSPEND_MEM: Save and restore peripheral base and DMA registers
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Acked-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If check_legacy_ioport() returns true, we leak *info.

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=11362Reported-by: NDaniel Marjamki <danielm77@spray.se>
Cc: Christian Krafft <krafft@de.ibm.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Corey Minyard <minyard@acm.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Release cmap memory allocated in the probe function.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

With commit 5ad31a57 ("rtc: remove BKL
for ioctl()"), RTC_UIE_ON ioctl cause double lock on rtc->ops_lock.
The ops_lock must not be held while set_uie() calls rtc_read_time()
which takes the lock.  Also clear_uie() does not need ops_lock.  This
patch fixes return value of RTC_UIE_OFF ioctl too.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: David Brownell <david-b@pacbell.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The name of brd block device is "ramdisk", it's not "brd".
(The block device is registered by register_blkdev(RAMDISK_MAJOR, "ramdisk")
So it should be unregistered by unregister_blkdev(RAMDISK_MAJOR, "ramdisk")
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Acked-by: NNick Piggin <npiggin@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We leak the memory allocated for the nbd_dev array at multiple places.
Fix them by either adding a kfree() or by rearranging code to return
before we allocate the memory.
Signed-off-by: NSven Wegener <sven.wegener@stealer.net>
Cc: Paul Clements <paul.clements@steeleye.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Blackfin RTC Driver: move irq request/free out of open/release and into probe/remove so that the non-dev interfaces (like sysfs) work as expected
Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

eeepc-laptop uses the hwmon struct after unregistering the device, causing
an oops on module unload.  Flip the ordering to fix.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Karol Kozimor <sziwan@users.sourceforge.net>
Cc: <stable@kernel.org>		[2.6.26.x]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Recent of_platform changes made of_bus_type_init() overwrite the bus
type's .dev_attrs list, meaning that the "name" attribute that ibmebus
devices previously had is no longer present.  This is a user-visible
regression which breaks the userspace eHCA support, since the eHCA
userspace driver relies on the name attribute to check for valid
adapters.

This fixes it by providing the "name" attribute in the generic OF
device code instead.  Tested on POWER.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

sbp2 was too quick to report .update() to the ieee1394 core as failed.
(Logged as "Failed to reconnect to sbp2 device!".)  The core would then
unbind sbp2 from the device.

This is not justified if the .update() failed because another bus reset
happened.  We check this and tell the ieee1394 that .update() succeeded,
and the core will call sbp2's .update() for the new bus reset as well.

This improves reconnection/re-login especially on buses with several
disks as they may issue bus resets in close succession when they come
online.

Tested by Damien Benoist.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

nodemgr_node_probe checked for generation increments too late and
therefore prematurely reported nodes as "suspended".

Fixes http://bugzilla.kernel.org/show_bug.cgi?id=11349.  Reported and
tested by Damien Benoist.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Regression since commit 73cf6023,
"ieee1394: use class iteration api":  The two loops for (1.) driver
updates and (2.) driver probes were replaced by a single loop with
bogus needs_probe checks.  Hence updates and probes were now intermixed,
and especially sbp2 updates (reconnects) held up longer than necessary.

While we fix it, change the needs_probe flag to bool type for clarity.

Tested by Damien Benoist.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

commit f2afa771 ("Input: paper over a bug in
Synaptics X driver") introduced a compiler warning on 64-bit platforms, as
sizeof() returns a size_t, not an (unsigned) int:

| drivers/input/evdev.c: In function 'handle_eviocgbit':
| drivers/input/evdev.c:684: warning: format '%d' expects type 'int', but argument 3 has type 'long unsigned int'

Use the proper `z' modifier for size_t, and make the printf() formats for the
sizes unsigned while we're at it.
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Use incoming network tuple as seed for NAT port randomization.
This avoids concerns of leaking net_random() bits, and also gives better
port distribution. Don't have NAT server, compile tested only.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>

[ added missing EXPORT_SYMBOL_GPL ]
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>