This patch moves filtering statement from ieee80211_rx_bss_info
which is called for both beacon and probe to ieee80211_rx_mgmt_probe_resp
and save few cycles in beacon parsing.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch replaces net_device arguments to mac80211 internal functions
with ieee80211_{local,sub_if_data} as appropriate.

It also does the same for many 802.11s mesh functions, and changes the
mesh path table to be indexed on sub_if_data rather than net_device.

If the mesh part needs to be a separate patch let me know, but since
mesh uses a lot of mac80211 functions which were being converted anyway,
the changes go hand-in-hand somewhat.

This patch probably does not convert all the functions which could be
converted, but it is a large chunk and followup patches will be
provided.
Signed-off-by: NJasper Bryant-Greene <jasper@amiton.co.nz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ETH_P_PAE belongs in if_ether.h with the other ETH_P_* definitions. This
patch moves it there.
Signed-off-by: NJasper Bryant-Greene <jasper@amiton.co.nz>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

While it is interesting to not add last-enum-markers because it allows gcc
to warn us of switch() statements missing a valid state, we really should
be handling memory corruption on a rfkill state with default clauses,
anyway.

So add RFKILL_STATE_MAX and use it where applicable.  It makes for safer
code in the long run.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rfkill is not a small, mere detail in wireless support.  Once it starts
supporting rfkill and users start counting on that support, a wireless
device is at risk of operating in dangerous conditions should rfkill
support fail to properly activate.

Therefore, add the required __must_check annotations on some key functions
of the rfkill API, for which the wireless drivers absolutely MUST handle
the failure mode safely in order to avoid a potentially dangerous situation
where the wireless transmitter is left enabled when the user don't want it
to.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add a second set of global states, "rfkill_default_states", to track the
state that will be used when the first rfkill class of a given type is
registered, and also to save "undo" information when rfkill_epo is called.

Add a new exported function, rfkill_set_default(), which can be used by
platform drivers to restore radio state saved by the platform across
reboots or shutdown.

Also, fix rfkill_epo to properly update rfkill_states, but still preserve a
copy of the state so that we can undo the effect of rfkill_epo later if we
want to.  Add rfkill_restore_states() to restore rfkill_states from the
copy.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Detect and abort with -EEXIST if rfkill_register is called twice on the
same rfkill struct.  And WARN_ON(it) for good measure.

While at it, flag when we are adding the first switch of a type, we will
need that information later.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLuis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The libertas thin firmware only supports usb devices, but the usb functions have
been kept separate to ease future support for other devices.
Signed-off-by: NLuis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLuis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch contains most of the libertastf driver, just lacking command helper
functions and usb specific functions. Currently, monitor, managed, ap and mesh
interfaces are supported. Even though this driver supports the same hardware as
the "libertas" driver, it uses a different (thin) firmware, that makes it
suitable for a mac80211 driver.
Signed-off-by: NLuis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLuis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Originally by Johannes Berg. This patch adds support for devices that do not
report their MAC address until the firmware is loaded. While the address is not
known, a multicast on is used.
Signed-off-by: NLuis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

All users are gone now.
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove the last users of the rx/tx_data->fc data members and use the
le16 frame_control from the header directly.
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

All users have been moved over to the version taking a le16 frame control
rather than a cpu-endian value.
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Those functions that still use ieee80211_get_hdrlen are moved over
to use the little endian frame control.
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

linux/ieee80211.h now has IEEE80211_QOS_CTL_LEN for this purpose.
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ieee80211_get_hdrlen_from_skb internally checks the skb is long enough to
hold the full ieee80211_hdr, else it returns zero.  Use ieee80211_hdrlen
which always returns the hdrlen and check the remaining room in the
skb explicitly when removing encryption headers or the qos control field.
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ieee80211_get_hdrlen_from_skb internally checks that the skb is long
enough to hold the full header, or it returns 0 if not.  The check in
ath5k does not check this case and assumes it always got the actual
header length which it then checks against the skb->len plus some headroom.

Change to ieee80211_hdrlen which always returns the hdrlen and keep the
existing headroom check.
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Acked-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds another level for debugging host command. This adds an
option to suppress the debug prints for sensitivity and link quality
commands.
Signed-off-by: NEsti Kummer <ester.kummer@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes struct iwl4965_lq_mngr it is not used.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

num_tbs is unsigned so the test doesn't work.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

remove drivers own implementation of radiotap in favor of the generic one
provided by mac80211.

also remove priv->add_radiotap because it is not used any more.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

use the rates ERP flag to derive CCK or OFDM modulation for the radiotap
header.

(it might be more correct to get this information from the hardware itself, but it
seems safe to assume this in most practical cases.)
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

and use it for the radiotap header
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

cleanup the rates structures used by ath5k. instead of separate driver and
mac80211 rate structures we now setup a static ieee80211_rate array and use it
directly. no conversion between two different rate structures has to be done
any more. a lot of unused and confusing junk was deleted.

renamed ath5k_getchannels into ath5k_setup_bands because this is what it does.
rewrote it to copy the bitrates correctly for each band. this is necessary for
running different hardware with the same driver (e.g. 5211 and 5212 based
cards).

add special handling of rates for AR5211 chipsets: it uses different rate codes
for CCK rates (which are actually like the other chips but with a 0xF mask).

setup a hardware code to rate index reverse mapping table for getting the rate
index of received frames.

the rates for control frames which have to be set in
ath5k_hw_write_rate_duration are now in one single array.

drivers/net/wireless/ath5k/ath5k.h:     Changes-licensed-under: ISC
drivers/net/wireless/ath5k/base.c:      Changes-licensed-under: 3-Clause-BSD
drivers/net/wireless/ath5k/base.h:      Changes-licensed-under: 3-Clause-BSD
drivers/net/wireless/ath5k/hw.c:        Changes-licensed-under: ISC
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds ieee80211_queue_stopped that let drivers to query
queue status
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use "menuconfig" to make wireless support one-click selectable.
Signed-off-by: NRobert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There were 3 code copy and pastes of reset. Unify the resets and place
in separate function.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is not allowed to use NETDEV_TX_BUSY in tx path anymore.
Signed-off-by: NDaniel Wagner <wagi@monom.org>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This enables draft-802.11s Mesh Point operation.  For that we need mesh
beaconing.  Tested with AR5212/AR5213 PCI card against Zydas and b43 mesh
nodes.
Signed-off-by: NAndrey Yurovsky <andrey@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Converts a test in error handling code to a sequence of labels.

The semantic match that found the problem is:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
expression E,E1,E2;
@@

E = alloc_etherdev(...)
... when != E = E1
if (...) { ... free_netdev(E); ... return ...; }
... when != E = E2
(
  if (...)
   {
   ... when != free_netdev(E);
   return dev; }
|
* if (...)
   {
   ... when != free_netdev(E);
   return ...; }
|
register_netdev(E)
)

// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To use these features, copy the boot2 and firmware images to /lib/firmware and:

echo <boot2_image_name> > /sys/class/net/ethX/lbs_flash_boot2
echo <firmware_image_name> > /sys/class/net/ethX/lbs_flash_fw
Signed-off-by: NBrian Cavagnolo <brian@cozybit.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>