This system BIOS sets a critical temperature to 65C,
which is too low.

https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=155496Signed-off-by: NLen Brown <len.brown@intel.com>

Some hardware will malfunction at a temperature below
the BIOS provided critical shutdown threshold.

This hook allows moving the critical trip points down
to a temperature which provokes a graceful shutdown
before the hardware malfunction.

http://bugzilla.kernel.org/show_bug.cgi?id=8884

WARNING: A trip-point override will not get noticed
until the system delivers a temperature change event,
or unless thermal zone polling is enabled.
eg. "thermal.tzp=10"
Signed-off-by: NLen Brown <len.brown@intel.com>

Reported-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Use DMI to:
1. enable polling (BIOS thermal events are broken)
2. disable active trip points (BIOS fan control is broken)
3. disable passive trip point (BIOS hard-codes it too low)

The actual temperature reading does work,
and with the aid of polling, the critical
trip point should work too.

http://bugzilla.kernel.org/show_bug.cgi?id=8842Signed-off-by: NLen Brown <len.brown@intel.com>

thermal.act=-1 disables all active trip points
in all ACPI thermal zones.

thermal.act=C, where C > 0, overrides all lowest temperature
active trip points in all thermal zones to C degrees Celsius.
Raising this trip-point may allow you to keep your system silent
up to a higher temperature.  However, it will not allow you to
raise the lowest temperature trip point above the next higher
trip point (if there is one).  Lowering this trip point may
kick in the fan sooner.

Note that overriding this trip-point will disable any BIOS attempts
to implement hysteresis around the lowest temperature trip point.
This may result in the fan starting and stopping frequently
if temperature frequently crosses C.

WARNING: raising trip points above the manufacturer's defaults
may cause the system to run at higher temperature and shorten
its life.
Signed-off-by: NLen Brown <len.brown@intel.com>

thermal.nocrt=1 disables actions on _CRT and _HOT
ACPI thermal zone trip-points.  They will be marked
as <disabled> in /proc/acpi/thermal_zone/*/trip_points.

There are two cases where this option is used:

1. Debugging a hot system crossing valid trip point.

   If your system fan is spinning at full speed,
   be sure that the vent is not clogged with dust.
   Many laptops have very fine thermal fins that are easily blocked.

   Check that the processor fan-sink is properly seated,
   has the proper thermal grease, and is really spinning.

   Check for fan related options in BIOS SETUP.
   Sometimes there is a performance vs quiet option.
   Defaults are generally the most conservative.

   If your fan is not spinning, yet /proc/acpi/fan/
   has files in it, please file a Linux/ACPI bug.

   WARNING: you risk shortening the lifetime of your
   hardware if you use this parameter on a hot system.
   Note that this refers to all system components,
   including the disk drive.

2. Working around a cool system crossing critical
   trip point due to erroneous temperature reading.

   Try again with CONFIG_HWMON=n
   There is known potential for conflict between the
   the hwmon sub-system and the ACPI BIOS.
   If this fixes it, notify lm-sensors@lm-sensors.org
   and linux-acpi@vger.kernel.org

   Otherwise, file a Linux/ACPI bug, or notify
   just linux-acpi@vger.kernel.org.
Signed-off-by: NLen Brown <len.brown@intel.com>

"thermal.psv=-1" disables passive trip points
for all ACPI thermal zones.

"thermal.psv=C", where 'C' is degrees Celsius,
overrides all existing passive trip points
for all ACPI thermal zones.

thermal.psv is checked at module load time,
and in response to trip-point change events.

Note that if the system does not deliver thermal zone
temperature change events near the new trip-point,
then it will not be noticed.  To force your custom
trip point to be noticed, you may need to enable polling:
eg. thermal.tzp=3000 invokes polling every 5 minutes.

Note that once passive thermal throttling is invoked,
it has its own internal Thermal Sampling Period (_TSP),
that is unrelated to _TZP.

WARNING: disabling or raising a thermal trip point
may result in increased running temperature and
shorter hardware lifetime on some systems.
Signed-off-by: NLen Brown <len.brown@intel.com>

Thermal Zone Polling frequency (_TZP) is an optional ACPI object
recommending the rate that the OS should poll the associated thermal zone.

If _TZP is 0, no polling should be used.
If _TZP is non-zero, then the platform recommends that
the OS poll the thermal zone at the specified rate.
The minimum period is 30 seconds.
The maximum period is 5 minutes.

(note _TZP and thermal.tzp units are in deci-seconds,
 so _TZP = 300 corresponds to 30 seconds)

If _TZP is not present, ACPI 3.0b recommends that the
thermal zone be polled at an "OS provided default frequency".

However, common industry practice is:
1. The BIOS never specifies any _TZP
2. High volume OS's from this century never poll any thermal zones

Ie. The OS depends on the platform's ability to
provoke thermal events when necessary, and
the "OS provided default frequency" is "never":-)

There is a proposal that ACPI 4.0 be updated to reflect
common industry practice -- ie. no _TZP, no polling.

The Linux kernel already follows this practice --
thermal zones are not polled unless _TZP is present and non-zero.

But thermal zone polling is useful as a workaround for systems
which have ACPI thermal control, but have an issue preventing
thermal events.  Indeed, some Linux distributions still
set a non-zero thermal polling frequency for this reason.

But rather than ask the user to write a polling frequency
into all the /proc/acpi/thermal_zone/*/polling_frequency
files, here we simply document and expose the already
existing module parameter to do the same at system level,
to simplify debugging those broken platforms.

Note that thermal.tzp is a module-load time parameter only.
Signed-off-by: NLen Brown <len.brown@intel.com>

"thermal.off=1" disables all ACPI thermal support at boot time.

CONFIG_ACPI_THERMAL=n can do this at build time.
"# rmmod thermal" can do this at run time,
as long as thermal is built as a module.

WARNING: On some systems, disabling ACPI thermal support
will cause the system to run hotter and reduce the
lifetime of the hardware.
Signed-off-by: NLen Brown <len.brown@intel.com>

modpost is going to use these to create e.g. acpi:ACPI0001
in modules.alias.
Signed-off-by: NThomas Renninger <trenn@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

Various pieces of code around the kernel want to be able to trigger an
orderly poweroff.  This pulls them together into a single
implementation.

By default the poweroff command is /sbin/poweroff, but it can be set
via sysctl: kernel/poweroff_cmd.  This is split at whitespace, so it
can include command-line arguments.

This patch replaces four other instances of invoking either "poweroff"
or "shutdown -h now": two sbus drivers, and acpi thermal
management.

sparc64 has its own "powerd"; still need to determine whether it should
be replaced by orderly_poweroff().
Signed-off-by: NJeremy Fitzhardinge <jeremy@xensource.com>
Acked-by: NLen Brown <lenb@kernel.org>
Signed-off-by: NChris Wright <chrisw@sous-sol.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David S. Miller <davem@davemloft.net>

if acpi_bus_get_device() returns NULL, print nothing
instead of "<NUL" in /proc/acpi/thermal_zone/*/trip_points
Signed-off-by: NThomas Renninger <trenn@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

For users with active thermal trip points, they need
the fan's name, rather than its address, to understand
where to look to observe and control fan state.
Signed-off-by: NThomas Renninger <trenn@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

The scheme where the thermal driver displayed the
cooling mode /proc/acpi/thermal_zone/*/cooling_mode
was flawed in two ways.

First, the success of _SCP doesn't actually mean
that the BIOS moved any trip points.
On many BIOS, _SCP is present, but does nothing.
So displaying what _SCP executed actually
was wrong more times than it was right.

Second, examining the relative position of the
trip points when the thermal_zone is added
is insufficient -- as the BIOS reserves the right
to change the trip points at run-time.

The only reliable way for the user to determine if
the thermal zone is in active, passive, or critical
mode is to examine the relative position of the trip points.
The user can do this without the kernel doing it
for them by looking in /proc/acpi/thermal_zone/*/trip_points

New contents for /proc/acpi/thermal_zone/*/cooling_mode:

If _SCP available:
"0 - Active; 1 - Passive\n"

If _SCP unavailable:
"<setting not supported>\n"
Signed-off-by: NLen Brown <len.brown@intel.com>

/proc/acpi/thermal_zone/*/trip_points displays
what the kernel reads from the BIOS via ACPI.

If you echo a string of ':' deliminted numbers to this file
then it will change what it displays.

But it shouldn't, since the kernel has no way to communicate
these changes to ACPI thermal zones.  ACPI thermal zone
trip points are read-only.

The kernel does have the opportunity to ask the BIOS to change
the trip points with _SCP - Set Cooling Policy.

Request Active Cooling Mode:
# echo 0 > /proc/acpi/thermal_zone/*/cooling_policy

Request Passive Cooling Mode:
# echo 1 > /proc/acpi/thermal_zone/*/cooling_policy

However, in practice it is quite rare for the BIOS
to support the optional _SCP, and it is even more rare
for the BIOS to export an _SCP that actually changes
the trip points.
Signed-off-by: NLen Brown <len.brown@intel.com>

Use relative time, not absolute.  Discovered by Jung-Ik (John) Lee
<jilee@google.com>.

Cc: Jung-Ik (John) Lee <jilee@google.com>
Acked-by: NLen Brown <lenb@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

http://bugzilla.kernel.org/show_bug.cgi?id=7570Signed-off-by: NKonstantin Karasyov <konstantin.a.karasyov@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

http://bugzilla.kernel.org/show_bug.cgi?id=4972Signed-off-by: NLen Brown <len.brown@intel.com>

After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there.  Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.

To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.

Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm.  I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: NTim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Cosmetic only.

Except in a single case, #define ACPI_*_DRIVER_NAME
were invoked 0 or 1 times.
Signed-off-by: NLen Brown <len.brown@intel.com>

It was erroneously used as a description rather than a name.

ie. turn this:

lenb@se7525gp2:/sys> ls bus/acpi/drivers
ACPI AC Adapter Driver  ACPI Embedded Controller Driver  ACPI Power Resource Driver
ACPI Battery Driver     ACPI Fan Driver                  ACPI Processor Driver
ACPI Button Driver      ACPI PCI Interrupt Link Driver   ACPI Thermal Zone Driver
ACPI container driver   ACPI PCI Root Bridge Driver      hpet

into this:

lenb@se7525gp2:~> ls /sys/bus/acpi/drivers
ac  battery  button  container  ec  fan  hpet  pci_link  pci_root  power  processor  thermal
Signed-off-by: NLen Brown <len.brown@intel.com>

cosmetic only

Make "module name" actually match the file name.
Invoke with ';' as leaving it off confuses Lindent and gcc doesn't care.
Fix indentation where Lindent did get confused.
Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLen Brown <len.brown@intel.com>

Add ACPI bus_type for Linux driver model.

1.	.shutdown method is added into acpi_driver.ops
	needed by bus_type operations.
2.	remove useless parameter 'int state' in .resume method.
3.	change parameter 'int state'
	to 'pm_message_t state' in .suspend method.

Note:	The new .uevent method mark ACPI drivers by PNPID instead of by name.
	Udev script needs to look for "HWID=" or "COMPTID=" to load
	ACPI drivers as a result.
Signed-off-by: NLi Shaohua <shaohua.li@intel.com>
Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NJan Engelhardt <jengelh@gmx.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

Daniel Ritz <daniel.ritz-ml@swissonline.ch> says:

The acpi driver suspend/resume patches that went in recently caused a regression
on my box (toshiba tecra 8000 laptop): after resume from swsusp the fan turns on
keeping blowing cold air out of my notebook. before the patches, the fan was off
and would only make noise when required. it's the same thing described in
bugzilla.kernel.org #5000. the acpi suspend/resume patches or at least parts of
them originate in this bug. now the last patch in the report (attach id 8438)
actually fixes the problem - for me and the reporter. this is a trimmed down
version of that patch.
Signed-off-by: NDaniel Ritz <daniel.ritz@gmx.ch>
Cc: Len Brown <len.brown@intel.com>
Cc: Sanjoy Mahajan <sanjoy@mrao.cam.ac.uk>
Cc: Pavel Machek <pavel@suse.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NPatrick Mochel <mochel@linux.intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NPatrick Mochel <mochel@linux.intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

- Use it instead of acpi_bus_get_device() where we can..
Signed-off-by: NPatrick Mochel <mochel@linux.intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NThomas Renninger <trenn@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

http://bugzilla.kernel.org/show_bug.cgi?id=5534

Thanks to Peter Wainwright for isolating the issue.
Thanks to Andi Kleen and Bob Moore for feedback.
Thanks to Richard Mace and others for testing.
Updates by Konstantin Karasyov.
Signed-off-by: NKonstantin Karasyov <konstantin.a.karasyov@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

http://bugzilla.kernel.org/show_bug.cgi?id=4364Signed-off-by: NKonstantin Karasyov <konstantin.a.karasyov@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NVasily Averin <vvs@sw.ru>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLen Brown <len.brown@intel.com>

Coverity: #601
Signed-off-by: NDave Jones <davej@redhat.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

http://bugzilla.kernel.org/show_bug.cgi?id=3410
https://bugzilla.novell.com/show_bug.cgi?id=131543Signed-off-by: NThomas Renninger <trenn@suse.de>
Signed-off-by: NKonstantin Karasyov <konstantin.a.karasyov@intel.com>
Signed-off-by: NAlexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: NYu Luming <luming.yu@gmail.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>

Signed-off-by: NLen Brown <len.brown@intel.com>