This system BIOS sets a critical temperature to 65C,
which is too low.

https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=155496Signed-off-by: NLen Brown <len.brown@intel.com>

Some hardware will malfunction at a temperature below
the BIOS provided critical shutdown threshold.

This hook allows moving the critical trip points down
to a temperature which provokes a graceful shutdown
before the hardware malfunction.

http://bugzilla.kernel.org/show_bug.cgi?id=8884

WARNING: A trip-point override will not get noticed
until the system delivers a temperature change event,
or unless thermal zone polling is enabled.
eg. "thermal.tzp=10"
Signed-off-by: NLen Brown <len.brown@intel.com>

Reported-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Use DMI to:
1. enable polling (BIOS thermal events are broken)
2. disable active trip points (BIOS fan control is broken)
3. disable passive trip point (BIOS hard-codes it too low)

The actual temperature reading does work,
and with the aid of polling, the critical
trip point should work too.

http://bugzilla.kernel.org/show_bug.cgi?id=8842Signed-off-by: NLen Brown <len.brown@intel.com>

thermal.act=-1 disables all active trip points
in all ACPI thermal zones.

thermal.act=C, where C > 0, overrides all lowest temperature
active trip points in all thermal zones to C degrees Celsius.
Raising this trip-point may allow you to keep your system silent
up to a higher temperature.  However, it will not allow you to
raise the lowest temperature trip point above the next higher
trip point (if there is one).  Lowering this trip point may
kick in the fan sooner.

Note that overriding this trip-point will disable any BIOS attempts
to implement hysteresis around the lowest temperature trip point.
This may result in the fan starting and stopping frequently
if temperature frequently crosses C.

WARNING: raising trip points above the manufacturer's defaults
may cause the system to run at higher temperature and shorten
its life.
Signed-off-by: NLen Brown <len.brown@intel.com>

thermal.nocrt=1 disables actions on _CRT and _HOT
ACPI thermal zone trip-points.  They will be marked
as <disabled> in /proc/acpi/thermal_zone/*/trip_points.

There are two cases where this option is used:

1. Debugging a hot system crossing valid trip point.

   If your system fan is spinning at full speed,
   be sure that the vent is not clogged with dust.
   Many laptops have very fine thermal fins that are easily blocked.

   Check that the processor fan-sink is properly seated,
   has the proper thermal grease, and is really spinning.

   Check for fan related options in BIOS SETUP.
   Sometimes there is a performance vs quiet option.
   Defaults are generally the most conservative.

   If your fan is not spinning, yet /proc/acpi/fan/
   has files in it, please file a Linux/ACPI bug.

   WARNING: you risk shortening the lifetime of your
   hardware if you use this parameter on a hot system.
   Note that this refers to all system components,
   including the disk drive.

2. Working around a cool system crossing critical
   trip point due to erroneous temperature reading.

   Try again with CONFIG_HWMON=n
   There is known potential for conflict between the
   the hwmon sub-system and the ACPI BIOS.
   If this fixes it, notify lm-sensors@lm-sensors.org
   and linux-acpi@vger.kernel.org

   Otherwise, file a Linux/ACPI bug, or notify
   just linux-acpi@vger.kernel.org.
Signed-off-by: NLen Brown <len.brown@intel.com>

"thermal.psv=-1" disables passive trip points
for all ACPI thermal zones.

"thermal.psv=C", where 'C' is degrees Celsius,
overrides all existing passive trip points
for all ACPI thermal zones.

thermal.psv is checked at module load time,
and in response to trip-point change events.

Note that if the system does not deliver thermal zone
temperature change events near the new trip-point,
then it will not be noticed.  To force your custom
trip point to be noticed, you may need to enable polling:
eg. thermal.tzp=3000 invokes polling every 5 minutes.

Note that once passive thermal throttling is invoked,
it has its own internal Thermal Sampling Period (_TSP),
that is unrelated to _TZP.

WARNING: disabling or raising a thermal trip point
may result in increased running temperature and
shorter hardware lifetime on some systems.
Signed-off-by: NLen Brown <len.brown@intel.com>

Thermal Zone Polling frequency (_TZP) is an optional ACPI object
recommending the rate that the OS should poll the associated thermal zone.

If _TZP is 0, no polling should be used.
If _TZP is non-zero, then the platform recommends that
the OS poll the thermal zone at the specified rate.
The minimum period is 30 seconds.
The maximum period is 5 minutes.

(note _TZP and thermal.tzp units are in deci-seconds,
 so _TZP = 300 corresponds to 30 seconds)

If _TZP is not present, ACPI 3.0b recommends that the
thermal zone be polled at an "OS provided default frequency".

However, common industry practice is:
1. The BIOS never specifies any _TZP
2. High volume OS's from this century never poll any thermal zones

Ie. The OS depends on the platform's ability to
provoke thermal events when necessary, and
the "OS provided default frequency" is "never":-)

There is a proposal that ACPI 4.0 be updated to reflect
common industry practice -- ie. no _TZP, no polling.

The Linux kernel already follows this practice --
thermal zones are not polled unless _TZP is present and non-zero.

But thermal zone polling is useful as a workaround for systems
which have ACPI thermal control, but have an issue preventing
thermal events.  Indeed, some Linux distributions still
set a non-zero thermal polling frequency for this reason.

But rather than ask the user to write a polling frequency
into all the /proc/acpi/thermal_zone/*/polling_frequency
files, here we simply document and expose the already
existing module parameter to do the same at system level,
to simplify debugging those broken platforms.

Note that thermal.tzp is a module-load time parameter only.
Signed-off-by: NLen Brown <len.brown@intel.com>

"thermal.off=1" disables all ACPI thermal support at boot time.

CONFIG_ACPI_THERMAL=n can do this at build time.
"# rmmod thermal" can do this at run time,
as long as thermal is built as a module.

WARNING: On some systems, disabling ACPI thermal support
will cause the system to run hotter and reduce the
lifetime of the hardware.
Signed-off-by: NLen Brown <len.brown@intel.com>

Make the needlessly global "acpi_event_seqnum" static.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLen Brown <len.brown@intel.com>

Send key=value pair along with the uevent instead of a plain value so that
userspace (udev) can handle it like common environment variables.
Signed-off-by: NHolger Macht <hmacht@suse.de>
Acked-by: NKristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Stephan Berberig <s.berberig@arcor.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

There must not be a new-line character in the uevent.  Otherwise, udev gets
confused.  Thanks to Kay Sievers for pointing it out.
Signed-off-by: NStephan Berberig <s.berberig@arcor.de>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

Commit 19d36ccd "x86: Fix alternatives
and kprobes to remap write-protected kernel text" uses code which is
being patched for patching.

In particular, paravirt_ops does patching in two stages: first it
calls paravirt_ops.patch, then it fills any remaining instructions
with nop_out().  nop_out calls text_poke() which calls
lookup_address() which calls pgd_val() (aka paravirt_ops.pgd_val):
that call site is one of the places we patch.

If we always do patching as one single call to text_poke(), we only
need make sure we're not patching the memcpy in text_poke itself.
This means the prototype to paravirt_ops.patch needs to change, to
marshal the new code into a buffer rather than patching in place as it
does now.  It also means all patching goes through text_poke(), which
is known to be safe (apply_alternatives is also changed to make a
single patch).

AK: fix compilation on x86-64 (bad rusty!)
AK: fix boot on x86-64 (sigh)
AK: merged with other patches
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Files using bits from paravirt.h should explicitly include it rather than
relying on it being pulled in by something else.
Signed-off-by: NJes Sorensen <jes@sgi.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

gcc-4.2 is a lot more picky about its symbol handling.  EXPORT_SYMBOL no
longer works on symbols that are undefined or defined with static scope.

For example, with CONFIG_PROFILE off, I see:

  kernel/profile.c:206: error: __ksymtab_profile_event_unregister causes a section type conflict
  kernel/profile.c:205: error: __ksymtab_profile_event_register causes a section type conflict

This patch moves the EXPORTs inside the #ifdef CONFIG_PROFILE, so we
only try to export symbols that are defined.

Also, in kernel/kprobes.c there's an EXPORT_SYMBOL_GPL() for
jprobes_return, which if CONFIG_JPROBES is undefined is a static
inline and gives the same error.

And in drivers/acpi/resources/rsxface.c, there's an
ACPI_EXPORT_SYMBOPL() for a static symbol. If it's static, it's not
accessible from outside the compilation unit, so should bot be exported.

These three changes allow building a zx1_defconfig kernel with gcc 4.2
on IA64.

[akpm@linux-foundation.org: export jpobe_return properly]
Signed-off-by: NPeter Chubb <peterc@gelato.unsw.edu.au>
Cc: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Git rid of "warning: passing arg 2 of `access_ok' makes pointer from integer
without a cast" reported on SH ...  most architectures use macros in that
test, SH uses inlined functions.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

sh:

drivers/mtd/mtdchar.c: In function `mtd_mmap':
drivers/mtd/mtdchar.c:817: error: dereferencing pointer to incomplete type
drivers/mtd/mtdchar.c:817: error: `VM_SHARED' undeclared (first use in this function)
drivers/mtd/mtdchar.c:817: error: (Each undeclared identifier is reported only once

Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Patch c5c34d48 (tty: flush flip buffer on
ldisc input queue flush) introduces a race condition which can lead to memory
leaks.

The problem can be triggered when tcflush() is called when data are being
pushed to the line discipline driver by flush_to_ldisc().

flush_to_ldisc() releases tty->buf.lock when calling the line discipline
receive_buf function. At that poing tty_buffer_flush() kicks in and sets both
tty->buf.head and tty->buf.tail to NULL. When flush_to_ldisc() finishes, it
restores tty->buf.head but doesn't touch tty->buf.tail. This corrups the
buffer queue, and the next call to tty_buffer_request_room() will allocate a
new buffer and overwrite tty->buf.head. The previous buffer is then lost
forever without being released.

(Thanks to Laurent for the above text, for finding, disgnosing and reporting
the bug)

- Use tty->flags bits for the flush status.

- Wait for the flag to clear again before returning

- Fix the doc error noted

- Fix flush of empty queue leaving stale flushpending

[akpm@linux-foundation.org: cleanup]
Signed-off-by: NAlan Cox <alan@redhat.com>
Acked-by: NPaul Fulghum <paulkf@microgate.com>
Cc: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Long ago I've noticed (but didn't pay much attention) that
spi_mpc83xx using PM calculations that differs from what
specs describe. I.e.

u8 pm = mpc83xx_spi->spibrg / (spi->max_speed_hz * 4);

While specs says: "The SPI baud rate generator clock source (either
system clock or system clock divided by 16, depending on DIV16 bit) is
divided by 4 * ([PM] + 1), a range from 4 to 64.".

Thus " - 1" is missing in the spi_mpc83xx's formula.

Why nobody noticed that bug? Probably because sysclk usually less then
user expects, e.g. you expect 200 MHz, but real clock is 198 MHz,
and integer rounding helps when this formula is used.

Suppose it's SPI in QE, SYSCLK at 198 MHz, thus SPIBRG at 99MHz, 25 MHz
requested.

PM = (99MHz / ( 25 MHz * 4 )), PM == 0, output SPICLK will be 24.75 MHz

At lower frequencies this bug is more noticeable, though.

And this bug shows itself in all its beauty if SYSCLK is equal or a bit
more than you expect (200 MHz SYSCLK, 100 MHz SPIBRG):
PM = (100MHz / ( 25 MHz * 4 )), PM == 1, output SPICLK will be 12.625 MHz!
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

For MPC8349E input to the SPI Baud Rate Generator is SYSCLK, but it's
SYSCLK/2 for MPC8323E (SPI in QE).  Fix this, and remove confusion by
renaming the mpc83xx_spi->sysclk member as mpc83xx_spi->spibrg.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

cm4000_cs.c and cm4040_cs.c call the internal release function with
an argument of wrong type. this fixes bug #8485
Signed-off-by: NDaniel Ritz <daniel.ritz@gmx.ch>
Cc: Bill McConnaughey <mcconnau@biochem.wustl.edu>
Cc: Natalie Protasevich <protasnb@gmail.com>
Cc: Harald Welte <laforge@gnumonks.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This builds upon my previous attempts to resolve some jitter problems seen
with the Matrox G450 and G550 -based cards, including odd disparities observed
between x86 and Power -based machines in a somewhat less hackish way (removing
the hacked ifdefs).

Apparently, preference should be given to use the DVI PLL when frequencies
permit, the Standard PLL otherwise.  The max pixel clock for the panellink
interface is extracted from the PInS information on the card and used as a
limit to determine which PLL to use.
Signed-off-by: NPaul A. Clarke <pc@us.ibm.com>
Acked-by: NPetr Vandrovec <petr@vandrovec.name>
Signed-off-by: NAntonino Daplas <adaplas@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

- better handling of the pvr2 registers based on more up to date information.

Testing shows that it seems to work pretty well at 16bpp, 24bpp and 32bpp -
including proper rendering of the boot logo at all levels (previously this was
a bit broken even at 16bpp) and giving white against black text.  Really
detailed testing (eg with X11) requires support for the maple bus - which
isn't (currently - next project assuming this is okay) available, but I have
no reason to think this is broken.

Signed-off by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NAntonino Daplas <adaplas@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Reported by: Adrian McMenamin <adrianmcmenamin@gmail.com>

This driver will oops when the pseudo_palette[] is written as u32 but not when
written as u16.  When written as u32, it corrupts the adjacent 'mmio_base'
field of struct pvr2fb_par.  Fix by using framebuffer_alloc()/release() to
allocate struct fb_info and struct pvr2fb_par, and create the pseudo_palette[]
as part of struct pvr2fb_par.
Signed-off-by: NAntonino Daplas <adaplas@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix compile warning ('map_override unused') if fbcon is compiled as a module
and CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=n.

[akpm@linux-foundation.org: cleanup]
Signed-off-by: NAntonino Daplas <adaplas@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Visualize-EG, Graffiti and A4450A graphics cards on PARISC can
be configured in double-buffer and standard mode, but the stifb
driver supports standard mode only.
This patch detects double-buffered cards more reliable.

It is a real bugfix for a very nasty problem for all parisc users which have
wrongly configured their graphic card.  The problem: The stifb graphics driver
will not detect that the card is wrongly configured and then nevertheless just
enables the graphics mode, which it shouldn't.  In the end, the user will see
no further updates / boot messages on the screen.

We had documented this problem already on our FAQ
(http://parisc-linux.org/faq/index.html#viseg "Why do I get corrupted graphics
with my Vis-EG/Graffiti/A4450A card?") but people still run into this problem.
 So having this fix in as early as possible can help us.
Signed-off-by: NHelge Deller <deller@gmx.de>
Signed-off-by: NAntonino Daplas <adaplas@gmail.com>
Cc: <stable@kernel.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The way this driver tries to implement HDIO_GETGEO it'll never be called.
Then again on ppc it probably will never be called anyway because it's
utterly pointless.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

This patch removes some redundant casts, does the kmalloc + memset to
k[cz]alloc conversion and it changes the error path to use goto (to avoid code
duplication).

 drivers/block/cpqarray.c | 49567 -> 48623 (-944 bytes)
 drivers/block/cpqarray.o | 178820 -> 178288 (-532 bytes)
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Acked-by: NMike Miller <mike.miller@hp.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

 drivers/block/cciss.c | 104285 -> 104168 (-117 bytes)
 drivers/block/cciss.o | 277400 -> 277124 (-276 bytes)
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Acked-by: NMike Miller <mike.miller@hp.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

This patch cleans up duplicate includes in
	drivers/block/
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>
Acked-by: NStephen Rothwell <sfr@canb.auug.org.au>
Cc: Satyam Sharma <satyam.sharma@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

This patch provides more information concerning REMAP operations on block
IOs. The additional information provides clearer details at the user level,
and supports post-processing analysis in btt.

o  Adds in partition remaps on the same device.
o  Fixed up the remap information in DM to be in the right order
o  Sent up mapped-from and mapped-to device information
Signed-off-by: NAlan D. Brunelle <alan.brunelle@hp.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Locking added so that multithreaded applications can now do writes
from different threads without the risk of storage corruption.
Signed-off-by: NMelissa Howland <melissah@us.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

If memory buffers above 2GB are used, diagnose 14 raises a specification
exception. This fix ensures that buffer allocation is done below the 2GB
boundary.
Signed-off-by: NMichael Holzheu <holzheu@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

If the z/VM reader is already open, it can happen that after opening the
Linux reader device, not the topmost file is processed. According the
semantics of the Linux z/VM unit record device driver, always the topmost
file has to be processed. With this fix an error is returned if that is
not the case.
Signed-off-by: NMichael Holzheu <holzheu@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

If a reader file with HOLD status is at the top of the reader queue, currently
all read requests will return data of the second file in the queue. But the
semantics of vmur is that always the topmost file is read. With this fix
-EPERM is returned on open, if the topmost reader file is in HOLD status.
Signed-off-by: NMichael Holzheu <holzheu@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
000000000ff9fb08 000000000ff9fb18 0000000000000002 0000000000000000
000000000ff9fbb8 000000000ff9fb30 000000000ff9fb30 0000000000104198
0000000000000000 0000000000000002 0000000000000000 0000000000000000
000000000ff9fb18 000000000000000c 000000000ff9fb18 000000000ff9fb88
0000000000448db0 0000000000104198 000000000ff9fb18 000000000ff9fb68
Call Trace:
([<00000000001040ea>] show_trace+0x12e/0x170)
 [<00000000001041f2>] show_stack+0xc6/0xf8
 [<0000000000104252>] dump_stack+0x2e/0x3c
 [<0000000000155f9c>] __lock_acquire+0x460/0x1048
 [<0000000000156c16>] lock_acquire+0x92/0xb8
 [<000000000043f406>] _spin_lock_irqsave+0x62/0x80
 [<0000000000121382>] complete+0x32/0x78
 [<000000001082b468>] ur_int_handler+0xc8/0xec [vmur]
 [<0000000000313216>] ccw_device_call_handler+0xae/0xd4
 [<0000000000310da4>] ccw_device_irq+0x5c/0x130
 [<0000000000312c84>] io_subchannel_irq+0x8c/0x118
 [<000000000030a88c>] do_IRQ+0x16c/0x194
 [<0000000000111a62>] io_no_vtime+0x16/0x1c
 [<0000000080001394>] 0x80001394
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

vmur allocates one contiguous kernel buffer to copy user data when creating
ccw programs for punch or printer. If big block sizes are used, under memory
pressure it can happen, that we do not get memory in one chunk. Now we
allocate memory for each single record to avoid high order allocations.
Signed-off-by: NMichael Holzheu <holzheu@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The slsb structure contained at the beginning of the qdio_q structure
must start on a 256 byte boundary. To make sure this is the case even
if slab debugging is turned on create an own slab cache for qdio_q
structures.
Besides that don't use the slab allocator to allocate whole pages. Use
the page allocator instead.
Also fix a few memory leaks in error handling code.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

sch->lock has been allocated in cio_validate_subchannel(), it must be
freed if cio_modify() fails.
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>