Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 24 3月, 2012 4 次提交
  3. 23 3月, 2012 1 次提交
    • J
      ntp: Fix leap-second hrtimer livelock · 6b43ae8a
      由 John Stultz 提交于 
      Since commit 7dffa3c6 the ntp
subsystem has used an hrtimer for triggering the leapsecond
adjustment. However, this can cause a potential livelock.

Thomas diagnosed this as the following pattern:
CPU 0                                                    CPU 1
do_adjtimex()
  spin_lock_irq(&ntp_lock);
    process_adjtimex_modes();				 timer_interrupt()
      process_adj_status();                                do_timer()
        ntp_start_leap_timer();                             write_lock(&xtime_lock);
          hrtimer_start();                                  update_wall_time();
             hrtimer_reprogram();                            ntp_tick_length()
               tick_program_event()                            spin_lock(&ntp_lock);
                 clockevents_program_event()
		   ktime_get()
                     seq = req_seqbegin(xtime_lock);

This patch tries to avoid the problem by reverting back to not using
an hrtimer to inject leapseconds, and instead we handle the leapsecond
processing in the second_overflow() function.

The downside to this change is that on systems that support highres
timers, the leap second processing will occur on a HZ tick boundary,
(ie: ~1-10ms, depending on HZ)  after the leap second instead of
possibly sooner (~34us in my tests w/ x86_64 lapic).

This patch applies on top of tip/timers/core.

CC: Sasha Levin <levinsasha928@gmail.com>
CC: Thomas Gleixner <tglx@linutronix.de>
Reported-by: NSasha Levin <levinsasha928@gmail.com>
Diagnoised-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NSasha Levin <levinsasha928@gmail.com>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>
      6b43ae8a
  5. 16 3月, 2012 2 次提交
  7. 15 2月, 2012 3 次提交
  9. 27 1月, 2012 12 次提交
  11. 31 12月, 2011 1 次提交
  13. 22 12月, 2011 1 次提交
  15. 19 12月, 2011 1 次提交
  17. 15 12月, 2011 1 次提交
  19. 12 12月, 2011 4 次提交
    • F
      nohz: Remove tick_nohz_idle_enter_norcu() / tick_nohz_idle_exit_norcu() · 1268fbc7
      由 Frederic Weisbecker 提交于 
      Those two APIs were provided to optimize the calls of
tick_nohz_idle_enter() and rcu_idle_enter() into a single
irq disabled section. This way no interrupt happening in-between would
needlessly process any RCU job.

Now we are talking about an optimization for which benefits
have yet to be measured. Let's start simple and completely decouple
idle rcu and dyntick idle logics to simplify.
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: NJosh Triplett <josh@joshtriplett.org>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
      1268fbc7
    • F
      nohz: Allow rcu extended quiescent state handling seperately from tick stop · 2bbb6817
      由 Frederic Weisbecker 提交于 
      It is assumed that rcu won't be used once we switch to tickless
mode and until we restart the tick. However this is not always
true, as in x86-64 where we dereference the idle notifiers after
the tick is stopped.

To prepare for fixing this, add two new APIs:
tick_nohz_idle_enter_norcu() and tick_nohz_idle_exit_norcu().

If no use of RCU is made in the idle loop between
tick_nohz_enter_idle() and tick_nohz_exit_idle() calls, the arch
must instead call the new *_norcu() version such that the arch doesn't
need to call rcu_idle_enter() and rcu_idle_exit().

Otherwise the arch must call tick_nohz_enter_idle() and
tick_nohz_exit_idle() and also call explicitly:

- rcu_idle_enter() after its last use of RCU before the CPU is put
to sleep.
- rcu_idle_exit() before the first use of RCU after the CPU is woken
up.
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: David Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
      2bbb6817
    • F
      nohz: Separate out irq exit and idle loop dyntick logic · 280f0677
      由 Frederic Weisbecker 提交于 
      The tick_nohz_stop_sched_tick() function, which tries to delay
the next timer tick as long as possible, can be called from two
places:

- From the idle loop to start the dytick idle mode
- From interrupt exit if we have interrupted the dyntick
idle mode, so that we reprogram the next tick event in
case the irq changed some internal state that requires this
action.

There are only few minor differences between both that
are handled by that function, driven by the ts->inidle
cpu variable and the inidle parameter. The whole guarantees
that we only update the dyntick mode on irq exit if we actually
interrupted the dyntick idle mode, and that we enter in RCU extended
quiescent state from idle loop entry only.

Split this function into:

- tick_nohz_idle_enter(), which sets ts->inidle to 1, enters
dynticks idle mode unconditionally if it can, and enters into RCU
extended quiescent state.

- tick_nohz_irq_exit() which only updates the dynticks idle mode
when ts->inidle is set (ie: if tick_nohz_idle_enter() has been called).

To maintain symmetry, tick_nohz_restart_sched_tick() has been renamed
into tick_nohz_idle_exit().

This simplifies the code and micro-optimize the irq exit path (no need
for local_irq_save there). This also prepares for the split between
dynticks and rcu extended quiescent state logics. We'll need this split to
further fix illegal uses of RCU in extended quiescent states in the idle
loop.
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: David Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: NJosh Triplett <josh@joshtriplett.org>
      280f0677
    • P
      rcu: Track idleness independent of idle tasks · 9b2e4f18
      由 Paul E. McKenney 提交于 
      Earlier versions of RCU used the scheduling-clock tick to detect idleness
by checking for the idle task, but handled idleness differently for
CONFIG_NO_HZ=y.  But there are now a number of uses of RCU read-side
critical sections in the idle task, for example, for tracing.  A more
fine-grained detection of idleness is therefore required.

This commit presses the old dyntick-idle code into full-time service,
so that rcu_idle_enter(), previously known as rcu_enter_nohz(), is
always invoked at the beginning of an idle loop iteration.  Similarly,
rcu_idle_exit(), previously known as rcu_exit_nohz(), is always invoked
at the end of an idle-loop iteration.  This allows the idle task to
use RCU everywhere except between consecutive rcu_idle_enter() and
rcu_idle_exit() calls, in turn allowing architecture maintainers to
specify exactly where in the idle loop that RCU may be used.

Because some of the userspace upcall uses can result in what looks
to RCU like half of an interrupt, it is not possible to expect that
the irq_enter() and irq_exit() hooks will give exact counts.  This
patch therefore expands the ->dynticks_nesting counter to 64 bits
and uses two separate bitfields to count process/idle transitions
and interrupt entry/exit transitions.  It is presumed that userspace
upcalls do not happen in the idle loop or from usermode execution
(though usermode might do a system call that results in an upcall).
The counter is hard-reset on each process/idle transition, which
avoids the interrupt entry/exit error from accumulating.  Overflow
is avoided by the 64-bitness of the ->dyntick_nesting counter.

This commit also adds warnings if a non-idle task asks RCU to enter
idle state (and these checks will need some adjustment before applying
Frederic's OS-jitter patches (http://lkml.org/lkml/2011/10/7/246).
In addition, validation of ->dynticks and ->dynticks_nesting is added.
Signed-off-by: NPaul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: NJosh Triplett <josh@joshtriplett.org>
      9b2e4f18
  21. 06 12月, 2011 2 次提交
  23. 02 12月, 2011 3 次提交
  25. 29 11月, 2011 1 次提交
  27. 22 11月, 2011 2 次提交
  29. 18 11月, 2011 1 次提交
  31. 11 11月, 2011 1 次提交
    • J
      clocksource: Avoid selecting mult values that might overflow when adjusted · d65670a7
      由 John Stultz 提交于 
      For some frequencies, the clocks_calc_mult_shift() function will
unfortunately select mult values very close to 0xffffffff.  This
has the potential to overflow when NTP adjusts the clock, adding
to the mult value.

This patch adds a clocksource.maxadj value, which provides
an approximation of an 11% adjustment(NTP limits adjustments to
500ppm and the tick adjustment is limited to 10%), which could
be made to the clocksource.mult value. This is then used to both
check that the current mult value won't overflow/underflow, as
well as warning us if the timekeeping_adjust() code pushes over
that 11% boundary.

v2: Fix max_adjustment calculation, and improve WARN_ONCE
messages.

v3: Don't warn before maxadj has actually been set

CC: Yong Zhang <yong.zhang0@gmail.com>
CC: David Daney <ddaney.cavm@gmail.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Chen Jie <chenj@lemote.com>
CC: zhangfx <zhangfx@lemote.com>
CC: stable@kernel.org
Reported-by: NChen Jie <chenj@lemote.com>
Reported-by: Nzhangfx <zhangfx@lemote.com>
Tested-by: NYong Zhang <yong.zhang0@gmail.com>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>
      d65670a7