Replace lp5521/5523_unregister_sysfs() with lp55xx_unregister_sysfs().

 On unloading the driver, running engines should be stopped.
 Use explicit driver function, lp5521/5523_stop_engine().

 Unused functions are removed.
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NBryan Wu <cooloney@gmail.com>

 LP5521 and LP5523 have a selftest function which is run via the sysfs.
 Use lp55xx driver data and R/W functions rather than lp5521/5523 private data
 and functions.
 Additionally, if-statements are changed for code simplicity.
 Unused functions, lp5521/5523_read() are removed.
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NBryan Wu <cooloney@gmail.com>

 lp5521/5523_register_sysfs() are replaced with lp55xx common driver function,
 lp55xx_register_sysfs().
 Chip specific device attributes are configurable using 'dev_attr_group'.

 Error condition name is changed:
 use specific error condition, 'err_register_sysfs' rather than unclear name,
 'fail2'.
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NBryan Wu <cooloney@gmail.com>

 LP55xx common driver provides generic firmware interface
 for running a LED pattern.
 LP5521 and LP5523 have many device attributes for running patterns.
 This patch cleans up those complex code.

 Removed device attributes:
 engine1_mode
 engine2_mode
 engine3_mode
 engine1_load
 engine2_load
 engine3_load
 engine1_leds
 engine2_leds
 engine3_leds

 All device attributes and functions are replaced with two callback functions,
 'firmware_cb' and 'run_engine'.

 New engine functions:
 lp5523_load/stop/run_engine(), lp5523_update_program_memory() and
 lp5523_wait_opmode_done()
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NBryan Wu <cooloney@gmail.com>

 To unregister led class devices and sysfs attributes,
 LP5521 and LP5523 have each driver function.
 This patch makes both drivers simple using common driver function,
 lp55xx_unregister_leds().

 And some unused variables are removed.
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NBryan Wu <cooloney@gmail.com>

 LED current is configurable via the sysfs.
 Max current is a read-only attribute.
 These attributes code can be shared in lp55xx common driver.

 Device attributes: 'led_current' and 'max_current'
 move to lp55xx common driver

 Replaced functions:
 show_max_current()  => lp55xx_show_max_current()
 show_current()      => lp55xx_show_current()
 store_current()     => lp55xx_store_current()

 LED setting function: set_led_current()
 Current registers are device specific, so configurable function is added
 in each driver.
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NBryan Wu <cooloney@gmail.com>

 lp5521_set_brightness() and lp5523_set_brightness() are replaced with
 common function, lp55xx_set_brightness().
 This function is invoked when the brightness of each LED channel is updated.
 LP5521 and LP5523 have different register address for the brightness control,
 so this work is done by chip specific brightness_work_fn().

 lp5521/5523_led_brightness_work():
 use lp55xx_led and lp55xx_chip data structure.
 use lp55xx write function.
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NBryan Wu <cooloney@gmail.com>

 lp5521_init_led() and lp5523_init_led() are replaced with one common function,
 lp55xx_init_led().
 Max channels is configurable, so it's used in lp55xx_init_led().

 'LP5523_LEDS' are changed to 'LP5523_MAX_LEDS'.

 lp55xx_set_brightness, lp55xx_led_attributes: skeleton
 Will be filled in next patches.
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NBryan Wu <cooloney@gmail.com>

 LED class devices are registered in lp5521_register_leds() and
 lp5523_register_leds().
 Two separate functions are merged into consolidated lp55xx function,
 lp55xx_register_leds().

 Error handling fix:
 Unregistering LEDS are handled in lp55xx_register_leds() when LED registration
 failure occurs. So each driver error handler is changed to 'err_register_leds'

 Chip dependency: 'brightness_work_fn' and 'set_led_current'
 To make the structure abstract, both functions are configured in each driver.
 Those functions should be done by each driver because register control is
 chip-dependant work.

 lp55xx_init_led: skeleton
 Will be filled in next patch
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NBryan Wu <cooloney@gmail.com>

 Two separate de-init functions are merged into one common function.
 And it is used in err_post_init of lp55xx_init_device().
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NBryan Wu <cooloney@gmail.com>

 lp5521/5523_init_device() are replaced with lp55xx common function,
 lp55xx_init_device().

 Error handler in init_device:
 deinit function are matched with 'err_post_init' section in
 lp55xx_init_device().

 Remove LP5523 engine intialization code:
 Engine functionality is not mandatory but optional.
 Moreover engine initialization is done internally with device reset command.
 Therefore, this code is unnecessary.
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NBryan Wu <cooloney@gmail.com>

 LP5521/5523 chip configuration is replaced with lp55xx common function,
 lp55xx_post_init_device().

 Name change:
 lp5521/5523_configure() to lp5521/5523_post_init_device()
 These are called in init function.

 Register access function
 Argument type is changed from 'i2c_client' to 'lp55xx_chip'.
 Use exported R/W functions of lp55xx common driver.

 Temporary variables in lp5521/5523_init_device()
 These functions will be removed but temporary variables are needed for
 blocking build warnings - incompatible pointer.
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NBryan Wu <cooloney@gmail.com>

 LP5521/5523 chip detection functions are replaced with lp55xx common function,
 lp55xx_detect_device().
 Chip dependent address and values are configurable in each driver.
 In init function, chip detection is executed.
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NBryan Wu <cooloney@gmail.com>

 LP5521/5523 reset device functions are moved to lp55xx common driver.
 Value of register address and value are chip dependent.
 Those are configured in each driver.
 In init function, reset command is executed.
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NBryan Wu <cooloney@gmail.com>

 LP5521/5523 platform data functions are moved to lp55xx common driver.
 New init function, lp55xx_init_device() is created.
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NBryan Wu <cooloney@gmail.com>

 This patch is a preceding step for making common lp55xx init function.

 Return code:
 Do not use 'OR' arithmetic for the result.
 If some error occurs, just return it.

 Remove engine verification code:
 To check whether internal engine works or not, many lines of code are executed.
 However, this job is unnecessary during the chip initialization because
 the engine usage is not mandatory but optional function.
 LED engines are enabled when specific LED pattern is loaded.
 Therefore, this verification code is removed.
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NBryan Wu <cooloney@gmail.com>

 LP5521 and LP5523 data structures have common features.
 Use common lp55xx data structures rather than chip specific data.
 Legacy code in probe is replaced with this new data structures.

 lp55xx_chip          : Common data between lp5521_chip and lp5523_chip
 lp55xx_led           : Common LED structure between lp5521_led and lp5523_led
 lp55xx_platform_data : Common platform data between lp5521_platform_data and
                        lp5523_platform_data
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NBryan Wu <cooloney@gmail.com>

 Change the name of chip data structure and platform data.
 This patch is a preceding step for cleaning up lp5521/5523 probe and remove.
 These data will be replaced with new lp55xx common data structures
 in next patch.
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NBryan Wu <cooloney@gmail.com>

 Chip specific function is configured when the device is initialized.
 So _configure() is moved to each device init function.

 If chip configuration gets failed, the device is de-initialized in
 each _init_device(), not probe().

 For compile error fix, function type declarations are added.
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NBryan Wu <cooloney@gmail.com>

 Use explicit each driver function rather than raw command.
 These function will be merged into the lp55xx common driver.
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NBryan Wu <cooloney@gmail.com>

 To make LED unregistration code simple, new function, _unregister_leds()
 is added in each driver.
 This patch is a preceding step for lp55xx common driver architecture.
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NBryan Wu <cooloney@gmail.com>

 To make LED initialization code simple, new function, _register_leds()
 is added at each driver.
 This patch is a preceding step for lp55xx common driver architecture.
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NBryan Wu <cooloney@gmail.com>

 Device de-initialization code is moved to _deinit_device() at each driver.
 This patch is a preceding step for lp55xx common driver architecture.
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NBryan Wu <cooloney@gmail.com>

 To make _probe() simple, device initialization code is moved to
 _init_device() at each driver.
 This patch is a preceding step for lp55xx common driver architecture.

 leds-lp5521:
 When 'lp5521_init_device()' gets failed, error handling should be 'fail1'
 rather than 'fail2'.
   fail1: releasing platform resource and return code
   fail2: releasing allocated LED devices with handling 'fail1'
 The 'lp5521_init_device()' is called before creating LED devices.
 Thus, 'goto fail1' is proper error handler of this function.
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NBryan Wu <cooloney@gmail.com>

CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Jan-Simon Moeller <jansimon.moeller@gmx.de>
Acked-by: NBryan Wu <cooloney@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Return the value obtained from i2c_smbus_read_byte_data() instead of
-EIO. Silences the following smatch warning:
drivers/leds/leds-lp5523.c:174 lp5523_read() info:
why not propagate 'ret' from i2c_smbus_read_byte_data() instead of -5?
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NBryan Wu <cooloney@gmail.com>

The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NBryan Wu <cooloney@gmail.com>

This patch fixes build warnings as below:

drivers/leds/leds-lp5523.c: In function 'lp5523_selftest':
drivers/leds/leds-lp5523.c:496:18: warning: 'adc' may be used uninitialized in this function [-Wuninitialized]
drivers/leds/leds-lp5523.c:471:5: warning: 'vdd' may be used uninitialized in this function [-Wuninitialized]
drivers/leds/leds-lp5523.c: In function 'lp5523_probe':
drivers/leds/leds-lp5523.c:252:9: warning: 'status' may be used uninitialized in this function [-Wuninitialized]
drivers/leds/leds-lp5523.c:201:5: note: 'status' was declared here

If lp5523_read() returns an error, problems will happen. Thus,
when lp5523_read() returns an error, it should be handled.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NBryan Wu <cooloney@gmail.com>

The last attribute should be terminated as NULL because any member of
attribute structure is accessed while adding the sysfs file.
If not, invalid address may cause the page fault problem.
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NBryan Wu <bryan.wu@canonical.com>

The LP5523 has 3 engines which are used for running LED patterns.
These engines should be off while unloading the driver.
Obviously, LP5523 platform data are used for releasing the resource
such like enable()/release_resource(), but these are not mandatory.
Therefore this patch is required without the platform data dependency.
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NBryan Wu <bryan.wu@canonical.com>

LP5523 driver supports both LP5523 and LP55231. The i2c device id
is one of the two - lp5523 or lp55231. So it's better to use
matching i2c device id while enumerating the device and naming LED
channels.
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NBryan Wu <bryan.wu@canonical.com>

To support LP55231 device, the device id is added. Additionally,
the i2c driver name is changed from lp5523 to lp5523x.
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NBryan Wu <bryan.wu@canonical.com>

(a) use LP5523_ENABLE rather than magic number 0x40
(b) use min_t() in lp5523_mux_parse()
(c) skip while loop and just return if invalid command
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NBryan Wu <bryan.wu@canonical.com>

The return value of this function is not handled any place, so
make it as void type.

And three if-statements are replaced with switch-statements.
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NBryan Wu <bryan.wu@canonical.com>

Turning off the brightness of each channel is required
when removing the driver.

So use flush_work() rather than cancel_work_sync() to execute
remaining brightness works.
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NBryan Wu <bryan.wu@canonical.com>

The name of each led channel is configurable.
If the name is NULL, just use the channel id for making the channel name
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NBryan Wu <bryan.wu@canonical.com>

Cc: Mathias Nyman <mathias.nyman@nokia.com>
Signed-off-by: NBryan Wu <bryan.wu@canonical.com>

Inside the error handling in lp5523_init_led(), there is a place that
calls to led_classdev_unregister().  When we unregister the LED drivers,
it tries to set the brightness to OFF.  In this driver setting the
brightness is done through a work queue and the work queue hasn't been
initialized yet.

The result is that we trigger a WARN_ON() in the __queue_work().

The fix is to move the INIT_WORK() in front of the call to
lp5523_init_led().

Matt Renzelmann found this using a bug finding tool.
Reported-by: NMatt Renzelmann <mjr@cs.wisc.edu>
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NBryan Wu <bryan.wu@canonical.com>

Saves ~50 bytes text and speeds things up.

Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Cc: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>