Watchdog configuration register and timer count register were interchanged,
causing wrong values to be written into both registers.
This caused watchdog triggered resets even if the watchdog was reset in time.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Acked-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Correct fix for the "ioremap() causes build failure on S390" should have been
a dependancy on HAS_IOMEM. So we add this dependancy also (and leave the driver
in the ARM section for now).
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

When shutting down the watchdog timer, special care must be taken
not to overwrite other bits in the register, as it may be shared
with other peripherals.

For example, on the Arcom Vulcan, the register is shared between
the watchdog and the PCI reset line...
Signed-off-by: NMarc Zyngier <maz@misterjones.org>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

A previous fix changed the WDTP function to use the period directly,
rather than subtracting from 63.  However the mask generation was
not changed, so the mask was coming out as 0.  This patch fixes it.
Signed-off-by: NLuuk Paulussen <luuk.paulussen@alliedtelesis.co.nz>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

This patch allows Watchdog timer to be selected for OMAP4 by fixing
Kconfig entry
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

[Novell Bug 581103] HP Watchdog driver has arbitrary (wrong) timeout limits.
Fix the lower timeout limit to a more appropriate value.
Signed-off-by: NThomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@kernel.org>

This patch adds the Intel Cougar Point PCH LPC Controller DeviceIDs for iTCO Watchdog.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@kernel.org>

Use of ioremap() causes build failure on S390.
Restrict the driver to ARM until another architecture comes along
and enables the driver for its own use.
Signed-off-by: NMarc Zyngier <maz@misterjones.org>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>

The watchdog_info struct cannot be a const since we dynamically fill
in the firmware version.
Signed-off-by: NSean MacLennan <smaclennan@pikatech.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h

percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: NTejun Heo <tj@kernel.org>
Guess-its-ok-by: NChristoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>

Since the intel 6300esb platform uses a dedicated PCI ID for
it's watchdog timer (00:1d.4), it's better and easier to have
this as a pci_driver.
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Before you can read or write from the i6300esb memeory mapped registers,
you need to unlock these. This is done by writing the magic numbers 0x80
and 0x86 to the reload register. The size of the reload register is 32bit
though.

Also binary 11 is hex 0x03 and not 0x11.
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Making this instance static exposes the code to SMP races, etc.
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Platform device drivers can use the .shutdown method to handle soft
shutdown's instead of reboot_notifier's.
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

make the watchdog_info struct const where possible.
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

This patch corrects author and copyright notices  following the split-up of
the GE Fanuc joint venture.
Signed-off-by: NMartyn Welch <martyn.welch@ge.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

It's possible that the platform is not allowing reboot via TCO timer
expiration.

Also, differentiate between not finding a chipset that has TCO, and the case
where TCO is present but the driver fails to initialize for some reason.
Signed-off-by: NNaga Chumbalkar <nagananda.chumbalkar@hp.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Clean-up driver:
* make release the reverse of probe so that both are consistent
* add WDIOC_GETSTATUS & WDIOC_GETBOOTSTATUS ioctls.
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

This driver adds support for the max63{69,70,71,72,73,74} family of
watchdog timer chips.

It has been tested on an Arcom Zeus (max6369).
Signed-off-by: NMarc Zyngier <maz@misterjones.org>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Technologic Systems TS-72xx SBCs have external glue logic
CPLD which includes watchdog timer. This driver implements
kernel support for that.
Signed-off-by: NMika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

This patch makes the ar7 clock code implement the Linux clk API. Drivers
using the various clocks available in the SoC are updated accordingly.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Acked-by: NWim Van Sebroeck <wim@iguana.be>
To: linux-mips@linux-mips.org
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: netdev@vger.kernel.org
Cc: David Miller <davem@davemloft.net>
Patchwork: http://patchwork.linux-mips.org/patch/881/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Relying on overflow/wrap around isn't exact because if you wrap far
enough, you get back to "valid" values.
Reported-by: NThorsten Pohlmann <pohlmann@tetronik.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@kernel.org>

Replace ARCH_OMAP34XX with ARCH_OMAP3
Signed-off-by: NTony Lindgren <tony@atomide.com>

Convert ARCH_OMAP24XX to ARCH_OMAP2
Signed-off-by: NTony Lindgren <tony@atomide.com>

clk_set_rate() is not supposed to be used to turn clocks on and off.
That's what clk_enable/clk_disable is for.
Acked-by: NWim Van Sebroeck <wim@iguana.be>
Acked-by: NVitaly Wool <vitalywool@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Acked-by: NWim Van Sebroeck <wim@iguana.be>
Acked-by: NVitaly Wool <vitalywool@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The mdelay function was used between I/O access commands, that causes peak
in CPU usage. Fix it by substitution mdelay to msleep.

Expand usage on fitPC2 compatible boards according to DMI identification.
Signed-off-by: NDenis Turischev <denis@compulab.co.il>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

This patch fixes a build failure[1] caused by the missing include of
timer.h and thus fixes the build failure.

Notably the build failure existed since October 2009! [2]

References:
[1] http://kisskb.ellerman.id.au/kisskb/buildresult/1983339/
[2] http://kisskb.ellerman.id.au/kisskb/buildresult/1351737/Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

This patch adds the Intel Cougar Point and PCH DeviceIDs for iTCO Watchdog.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Use resource_size().
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Kevin Hilman <khilman@ti.deeprootsystems.com>
Cc: Ulrik Bech Hald <ubh@ti.com>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Vincent Sanders <support@simtec.co.uk>
Acked-by: NThierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>

add PCI ID for the Intel EP80579 (Tolapai) SoC
Signed-off-by: NImre Kaloz <kaloz@openwrt.org>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Update to the new cs5535_mfgpt* API.  The geode-specific wording should
eventually be dropped from this driver...
Signed-off-by: NAndres Salomon <dilinger@collabora.co.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The platform has never been fully merged 
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Cc: Thomas Koeller <thomas.koeller@baslerweb.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mtd@lists.infradead.org
Acked-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Acked-by: NWim Van Sebroeck <wim@iguana.be>

Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch renames function names like twl4030_i2c_write_u8,
twl4030_i2c_read_u8 to twl_i2c_write_u8, twl_i2c_read_u8
and also common variable in twl-core.c
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The upcoming TWL6030 is companion chip for OMAP4 like the current TWL4030
for OMAP3. The common modules like RTC, Regulator creates opportunity
to re-use the most of the code from twl4030.

This patch renames few common drivers twl4030* files to twl* to enable
the code re-use.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Remove the old WDT implementation.
Signed-off-by: NAlbrecht Dreß <albrecht.dress@arcor.de>
Acked-by: NWim Van Sebroeck <wim@iguana.be>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

That is "success", "unknown", "through", "performance", "[re|un]mapping"
, "access", "default", "reasonable", "[con]currently", "temperature"
, "channel", "[un]used", "application", "example","hierarchy", "therefore"
, "[over|under]flow", "contiguous", "threshold", "enough" and others.
Signed-off-by: NAndré Goddard Rosa <andre.goddard@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Cleanup the documentation about the supported chipsets.
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Add the Intel Ibex Peak (PCH) Device IDs to iTCO_wdt.c.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>