This commit removes USB_GADGET_DUALSPEED and USB_GADGET_SUPERSPEED
Kconfig options.  Since now kernel allows many UDC drivers to be
compiled, those options may turn to no longer be valid.  For
instance, if someone decides to build UDC that supports super
speed and UDC that supports high speed only, the latter will be
"assumed" to support super speed since USB_GADGET_SUPERSPEED will
be selected by the former.

The test of whether CONFIG_USB_GADGET_*SPEED was defined was just
an optimisation which removed otherwise dead code (ie. if UDC is
not dual speed, there is no need to handle cases that can happen
if speed is high).  This commit removes those checks.
Signed-off-by: NMichal Nazarewicz <mina86@mina86.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Enabled the flag so that musb_dsps glue file can be used for am335x
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

TI81XX platform has two musb interfaces and uses CPPI4.1 DMA engine.
It has builtin USB PHYs as AM35x. The current set of patches adds support
for one instance and only in PIO mode.

[ balbi@ti.com : make it compile and solve a "may be used
	uninitialized" warning ]
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NRavi Babu <ravibabu@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The whole thing depends on USB_MUSB_HDRC, just add an 'if'.
Signed-off-by: NFelipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Shuffle the code a bit so the description is at the top.
Signed-off-by: NFelipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

musb core driver and tusb6010 glue layer don't
depend on anything which is ARCH-specific. It
builds fine on x86 and ARM. Dropping the dependency
so we can compile-test on linux-next.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The logic to allow only one DMA driver in MUSB is currently
flawed, because it also allows picking no DMA driver at all
and also not selecting PIO mode.

Using a choice statement makes this foolproof for now and
also simplifies the Makefile.

Unfortunately, we will have to revisit this when we start
supporting multiple ARM platforms in a single kernel binary,
because at that point we will actually need to select
multiple DMA drivers and pick the right one at run-time.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

USB_MUSB_HDRC depends on USB_GADGET_DUALSPEED.  If HDRC is selected
but DUALSPEED is not, the kernel oopses:

[    3.132781] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[    3.141296] pgd = c0004000
[    3.144134] [00000000] *pgd=00000000
[    3.147918] Internal error: Oops: 5 [#1] SMP
[    3.152404] Modules linked in:
[    3.155609] CPU: 0    Not tainted  (3.1.0-rc9-wl+ #417)
[    3.161132] PC is at composite_setup+0x738/0xbb4
[    3.165985] LR is at vprintk+0x400/0x47c
[    3.170135] pc : [<c031df90>]    lr : [<c004c150>]    psr: 60000093
[    3.170135] sp : c065dd50  ip : dfb1f0fc  fp : c065ddbc
[    3.182220] r10: 00000000  r9 : df8fcae8  r8 : df8fcaa0
[    3.187713] r7 : 00000000  r6 : df8eaa20  r5 : dfae8ea0  r4 : 00000000
[    3.194580] r3 : df8fcae8  r2 : 00010002  r1 : c065dc40  r0 : 00000047
[    3.201446] Flags: nZCv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
[    3.209228] Control: 10c53c7d  Table: 8000404a  DAC: 00000015
[    3.215270] Process swapper (pid: 0, stack limit = 0xc065c2f8)
[    3.221405] Stack: (0xc065dd50 to 0xc065e000)
[...]
[    3.415405] [<c031df90>] (composite_setup+0x738/0xbb4) from [<c0310d18>] (musb_g_ep0_irq+0x9d0/0xaf8)
[    3.425109] [<c0310d18>] (musb_g_ep0_irq+0x9d0/0xaf8) from [<c030fb04>] (musb_interrupt+0xb48/0xc74)
[    3.434722] [<c030fb04>] (musb_interrupt+0xb48/0xc74) from [<c030fc98>] (generic_interrupt+0x68/0x80)
[    3.444458] [<c030fc98>] (generic_interrupt+0x68/0x80) from [<c0095204>] (handle_irq_event_percpu+0x9c/0x234)
[    3.454925] [<c0095204>] (handle_irq_event_percpu+0x9c/0x234) from [<c00953e8>] (handle_irq_event+0x4c/0x6c)
[    3.465270] [<c00953e8>] (handle_irq_event+0x4c/0x6c) from [<c0097e10>] (handle_fasteoi_irq+0xd8/0x110)
[    3.475158] [<c0097e10>] (handle_fasteoi_irq+0xd8/0x110) from [<c0094d2c>] (generic_handle_irq+0x34/0x3c)
[    3.485260] [<c0094d2c>] (generic_handle_irq+0x34/0x3c) from [<c0014ae4>] (handle_IRQ+0x88/0xc8)
[    3.494537] [<c0014ae4>] (handle_IRQ+0x88/0xc8) from [<c00085b0>] (asm_do_IRQ+0x18/0x1c)
[    3.503051] [<c00085b0>] (asm_do_IRQ+0x18/0x1c) from [<c0429e78>] (__irq_svc+0x38/0xc0)

This patch changes Kconfig so that USB_GADGET_DUALSPEED is selected
automatically by USB_MUSB_HDRC.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

ARCH_U8500 covers both MACH_U8500 and MACH_U5500
Reported-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NMian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

After 62285963 (usb: musb: drop a gigantic amount of ifdeferry):

 - USB_GADGET_MUSB_HDRC is no longer selectable because it
   depends on the removed USB_MUSB_PERIPHERAL and USB_MUSB_OTG
   options

 - The Kconfig comment still says "Enable Host or Gadget support
   to see Inventra options", even though you now need to enable
   both of them to see Inventra options.

Fix the dependency and drop the anyway unnecessary comment.
Signed-off-by: NRabin Vincent <rabin@rab.in>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

After 62285963 (usb: musb: drop a gigantic amount of ifdeferry):

 - USB_GADGET_MUSB_HDRC is no longer selectable because it
   depends on the removed USB_MUSB_PERIPHERAL and USB_MUSB_OTG
   options

 - The Kconfig comment still says "Enable Host or Gadget support
   to see Inventra options", even though you now need to enable
   both of them to see Inventra options.

Fix the dependency and drop the anyway unnecessary comment.
Signed-off-by: NRabin Vincent <rabin@rab.in>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

the MUSB IP is always OTG, so there's no point
in adding so many ifdefs on the code. Drop those
and always compile the driver for OTG support.

This also allows us to drop the useless "driver
mode" choice. For doing that, we need to make
musb depend on both Host and Peripheral side.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NMian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This in part reverts commit 7a180e70.
(usb: musb: temporarily make it bool) and while
at that we also allow glue layers to be compiled
as modules.

There are still some other changes needed
until we can have a fully functional build
with this setup, but we're getting there.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We have a generic way of enabling/disabling
different debug messages on a driver called
DYNAMIC_PRINTK. Anyone interested in enabling
just part of the debug messages, please read
the documentation under:

Documentation/dynamic-debug-howto.txt

for information on how to use that great
infrastructure.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Due to the recent changes to musb's glue layers,
we can't compile musb-hdrc as a module - compilation
will break due to undefined symbol musb_debug. In
order to fix that, we need a big re-work of the
debug support on the MUSB driver.

Because that would mean a lot of new code coming
into the -rc series, it's best to defer that to
next merge window and for now just disable module
support for MUSB.

Once we get the refactor of the debugging support
done, we can simply revert this patch and things
will go back to normal again.

Cc: stable@kernel.org # v2.6.38
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Selecting the twl6030-usb for OMAP4430SDP and OMAP4PANDA boards and
adding OMAP4 internal phy code for compilation
Signed-off-by: NHema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Initial support for u8500 and u5500 platform.
Signed-off-by: NMian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

change all ocurrences of musb_hdrc to musb-hdrc.

We will call glue layer drivers musb-<glue layer>,
so in order to keep things somewhat standard, let's
change the underscore into a dash.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This will make things simpler when choosing which
glue layer to compile. It avoids a lot of magic
around the "default" Kconfig option and lets the
user choose what exactly s/he wants to compile.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

AM35x has musb interface and uses CPPI4.1 DMA engine.
Current patch supports only PIO mode. DMA support can be
added later once basic CPPI4.1 DMA patch is accepted.

Also added USB_MUSB_AM35X which is required to differentiate musb ips
between OMAP3x and AM35x. This config would be used to for below
purposes,
        - Select am35x.c instead of omap2430.c for compilation
          at drivers/usb/musb directory. Please note there are
          significant differneces in these two files as musb ip
          in quite different on AM35x.

	  Please note that in multi omap configuration only omap2430.c
	  file will get compiled and we would require to select only
	  AM35x based board config to compile am35x.c

        - Select workaround codes applicable for AM35x musb issues.
          one such workaround is for bytewise read issue on AM35x.
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Texas Instruments DA8xx/OMAP-L1x glue layer for the
MUSBMHRDC driver.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NYadviga Grigorieva <yadviga@ru.mvista.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch updates the Makefile to build the
MUSB driver for OMAP4. It also sets the Kconfig
options for OMAP4.
Signed-off-by: NMaulik Mankad <x0082077@ti.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

CONFIG_ARCH_DAVINCI now embraces both the "real" DaVinci and DA8xx/OMAP-L1x --
on which the DaVinci glue layer won't work. Change the Makefile dependency to
CONFIG_ARCH_DAVINCI_DMx which corresponds to "real" DaVinci.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Replace ARCH_OMAP34XX with ARCH_OMAP3
Signed-off-by: NTony Lindgren <tony@atomide.com>

Otherwise we get the link failure:
drivers/built-in.o: In function 'musb_platform_init':
drivers/usb/musb/blackfin.c:300: undefined reference to 'usb_nop_xceiv_register'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: NCliff Cai <cliff.cai@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Do not allow MUSB driver to be selected on derivatives that don't have the
MUSB controller on them.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NCliff Cai <cliff.cai@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The MUSB code relies on platform implementations that currently only
exists for Arm and Blackfin processors, so have the MUSB Kconfig depend
upon those arches.

This should prevent other arches from building MUSB via randconfig.
Reported-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The Blackfin port doesn't support HAVE_CLK and the musb driver works fine
with support stubbed out, so take the existing Blackfin clk stubs and move
them to common musb code so we can drop the Kconfig dependency.
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

OMAP3EVM uses ISP1504 phy which doesn't require any programming and
thus has to use NOP otg transceiver.

Cleanups being done:
	- Remove unwanted code in usb-musb.c file
	- Register NOP in OMAP3EVM board file using
	  usb_nop_xceiv_register().
	- Select NOP_USB_XCEIV for OMAP3EVM boards.
	- Don't enable TWL4030_USB in omap3_evm_defconfig
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NEino-Ville Talvala <talvala@stanford.edu>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Let the otg_transceiver in MUSB be managed by an external driver;
don't assume it's integrated.  OMAP3 chips need it to be external,
and there may be ways to interact with the transceiver which add
functionality to the system.

Platform init code is responsible for setting up the transeciver,
probably using the NOP transceiver for integrated transceivers.
External ones will use whatever the board init code provided,
such as twl4030 or something more hands-off.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Partial support for DaVinci DM355, on the EVM board; peripheral
mode should work, once mainline merges DM355 support.  Missing:

  (a) renumbering the GPIO for DRVVBUS on the DM6446 EVM,
      when DAVINCI_N_GPIO increases;

  (b) disabling DM355_DEEPSLEEP.DRVVBUS_OVERRIDE so VBUS is
      driven according to the ID signal, if cpu_is_..._dm355()

The new PHY control bits are ignored on DM6446.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Blackfin MUSB Kconfig text didn't properly parenthesise its
dependencies.  This was visible in non-Blackfin configs by the
way the user interfaces lost track of dependencies, when doing
a bunch of test builds.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The DaVinci code had an implementation of the OTG transceiver glue
too; make it use the new-standard one.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Minor musb_hdrc updates:

  - so it'll build on DaVinci, given relevant platform updates;
      * remove support for an un-shipped OTG prototype
      * rely on gpiolib framework conversion for the I2C GPIOs
      * the <asm/arch/hdrc_cnf.h> mechanism has been removed

  - catch comments up to the recent removal of the per-SOC header
    with the silicon configuration data;

  - and remove two inappropriate "inline" declarations which
    just bloat host side code.

There are still some more <asm/arch/XYZ.h> ==> <mach/XYZ.h>
changes needed in this driver, catching up to the relocation
of most of the include/asm-arm/arch-* contents.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Cc: stable <stable@kernel.org> [2.6.27]
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In file included from drivers/usb/musb/musb_core.h:59,
                 from drivers/usb/musb/musb_core.c:108:
drivers/usb/musb/musb_io.h:42: error: conflicting types for '__raw_readsl'
/usr/src/devel/arch/sh/include/asm/io.h:112: error: previous declaration of '__raw_readsl' was here
drivers/usb/musb/musb_io.h:42: error: conflicting types for '__raw_readsl'
/usr/src/devel/arch/sh/include/asm/io.h:112: error: previous declaration of '__raw_readsl' was here
drivers/usb/musb/musb_io.h:44: error: conflicting types for 'readsw'
/usr/src/devel/arch/sh/include/asm/io.h:164: error: previous definition of 'readsw' was here
drivers/usb/musb/musb_io.h:46: error: conflicting types for 'readsb'
/usr/src/devel/arch/sh/include/asm/io.h:163: error: previous definition of 'readsb' was here
drivers/usb/musb/musb_io.h:49: error: conflicting types for '__raw_writesl'
/usr/src/devel/arch/sh/include/asm/io.h:111: error: previous declaration of '__raw_writesl' was here
drivers/usb/musb/musb_io.h:49: error: conflicting types for '__raw_writesl'
/usr/src/devel/arch/sh/include/asm/io.h:111: error: previous declaration of '__raw_writesl' was here
drivers/usb/musb/musb_io.h:51: error: conflicting types for 'writesw'
/usr/src/devel/arch/sh/include/asm/io.h:164: error: previous definition of 'writesw' was here
drivers/usb/musb/musb_io.h:53: error: conflicting types for 'writesb'
/usr/src/devel/arch/sh/include/asm/io.h:163: error: previous definition of 'writesb' was here

Cc: Karsten Keil <kkeil@suse.de>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We can change debugging level on the fly via
/sys/module/musb_hdrc/parameters/debug.

We can also get rid of the LOGLEVEL facility in Kconfig
and rely only in module parameter.

Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds support for MUSB and TUSB controllers
integrated into omap2430 and davinci. It also adds support
for external tusb6010 controller.

Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>