Since kernel 3.8, the initialization for Stellar (sms1000)
devices are broken.
Those devices have a behaviour different than usual sms1100
and sms2270: they start with one USB ID (devices in cold state),
but after firmware load, they get a different USB ID.
This weren't docummented at the driver. So, the patches that added
support for sms2270 broke it.
Properly documment it, and provide a debug log that allows to
follow all phases of the device initialization:
	smsusb_probe: board id=13, interface number 0
	smsusb_probe: interface 0 won't be used. Expecting interface 1 to popup
	smsusb_probe: board id=13, interface number 1
	smsusb_probe: smsusb_probe 1
	smsusb_probe: endpoint 0 81 02 64
	smsusb_probe: endpoint 1 02 02 64
	smsusb_probe: stellar device in cold state was found at usb\4-2.
	smsusb1_load_firmware: sent 38144(38144) bytes, rc 0
	smsusb1_load_firmware: read FW dvbt_bda_stellar_usb.inp, size=38144
	smsusb_probe: stellar device now in warm state
	usbcore: registered new interface driver smsusb
	usb 4-2: USB disconnect, device number 52
	usb 4-2: new full-speed USB device number 53 using uhci_hcd
	usb 4-2: New USB device found, idVendor=187f, idProduct=0100
	usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
	usb 4-2: Product: SMS DVBT-BDA Receiver
	usb 4-2: Manufacturer: Siano Mobile Silicon
	smsusb_probe: board id=1, interface number 0
	smsusb_probe: smsusb_probe 0
	smsusb_probe: endpoint 0 81 02 64
	smsusb_probe: endpoint 1 02 02 64
	smsusb_init_device: in_ep = 81, out_ep = 02
	smscore_register_device: allocated 50 buffers
	smscore_register_device: device ffff88012a00bc00 created
	smsusb_init_device: smsusb_start_streaming(...).
	smscore_set_device_mode: set device mode to 4
	smsusb1_detectmode: 4 "SMS DVBT-BDA Receiver"
	smsusb_sendrequest: sending MSG_SMS_INIT_DEVICE_REQ(578) size: 12
	smsusb_onresponse: received MSG_SMS_INIT_DEVICE_RES(579) size: 12
	smscore_set_device_mode: Success setting device mode.
	smscore_init_ir: IR port has not been detected
	smscore_start_device: device ffff88012a00bc00 started, rc 0
	smsusb_init_device: device 0xffff88002cfa6000 created
	smsusb_probe: Device initialized with return code 0
	DVB: registering new adapter (Siano Stellar Digital Receiver)
	usb 4-2: DVB: registering adapter 0 frontend 0 (Siano Mobile Digital MDTV Receiver)...
	smscore_register_client: ffff88012174a000 693 1
	sms_board_dvb3_event: DVB3_EVENT_HOTPLUG
	smsdvb_hotplug: success
	smsdvb_module_init:
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>
Tested-by: NAndré Roth <neolynx@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Some messages are not clear, some are debug data, but are
shown as errors, and one message is duplicated.
Cleanup that mess in order to provide a cleaner log.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>
Tested-by: NAndré Roth <neolynx@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

At this bugzilla and similar ones:
   https://bugzilla.kernel.org/show_bug.cgi?id=60645
Those debug messages were seen as errors, but they're just debug
data, and are OK to appear on sms1100 and sms2270. Re-tag them
to appear only if debug is enabled.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>
Tested-by: NAndré Roth <neolynx@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This patch will fix the situation where the mutex was left in a
locked state if for some reason the FE init failed.
Signed-off-by: NLuis Alves <ljalvs@gmail.com>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

On certain platforms a sequence of dma_map_sg() and dma_unmap_sg()
discards data previously stored in the buffers. Build video headers
only after the DMA is completed.
Signed-off-by: NKrzysztof Ha?asa <khalasa@piap.pl>
[hans.verkuil@cisco.com: fix merge problems due to the recent solo sg_table changes]
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Signed-off-by: NKrzysztof Ha?asa <khalasa@piap.pl>
[hans.verkuil@cisco.com: fix merge problems due to the recent solo sg_table changes]
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Signed-off-by: NKrzysztof Ha?asa <khalasa@piap.pl>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

[m.chehab@samsung.com: Fix CodingStyle: don't use 2 statements on just one line]
Signed-off-by: NKrzysztof Ha?asa <khalasa@piap.pl>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The "|" operation has higher precedence that "?:" so this couldn't
return both flags set at once as intended.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Fix to return -ENOMEM in the new i2c client and create workqueue error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This patch proposes to remove the IRQF_DISABLED flag from
davinci media platform drivers.
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: NMichael Opdenacker <michael.opdenacker@free-electrons.com>
Acked-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

If NO_DMA=y:
warning: (... && VIDEO_RENESAS_VSP1 && ...) selects VIDEOBUF2_DMA_CONTIG which has unmet direct dependencies (MEDIA_SUPPORT && HAS_DMA)
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_mmap’:
drivers/media/v4l2-core/videobuf2-dma-contig.c:202: error: implicit declaration of function ‘dma_mmap_coherent’
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_get_base_sgt’:
drivers/media/v4l2-core/videobuf2-dma-contig.c:385: error: implicit declaration of function ‘dma_get_sgtable’
make[7]: *** [drivers/media/v4l2-core/videobuf2-dma-contig.o] Error 1
VIDEO_RENESAS_VSP1 (which doesn't have a platform dependency) selects
VIDEOBUF2_DMA_CONTIG, but the latter depends on HAS_DMA.
Make VIDEO_RENESAS_VSP1 depend on HAS_DMA to fix this.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

We must not assume that the PCI device is already enabled.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

We must call iounmap() and pci_dev_put() when removed and on
the probe failure path.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Use phys_addr_t and log format %pa.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Reviewed-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Fix to return -ENODEV in the subdevice register error handling.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

...and remove the frontend pointer param from cx24117_attach()
Signed-off-by: NLuis Alves <ljalvs@gmail.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Signed-off-by: NLuis Alves <ljalvs@gmail.com>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add support for the cx24117 dual DVB-S/S2 frontend.
Signed-off-by: NLuis Alves <ljalvs@gmail.com>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

There is an asymmetry in ttusb_dec_init_usb()-ttusb_init_rc()
and ttusb_dec_exit_usb()-ttusb_dec_exit_rc() in terms of resources
allocated-deallocated. irq_urb and irq_buffer are allocated in
ttusb_dec_init_usb(), while they are deallocated in ttusb_dec_exit_rc().
As a result there is a leak of them in ttusb_dec_probe().
The patch fixes the asymmetry and a leak on a failure path in ttusb_dec_init_usb().
By the way, it
- removes usage of -1 as a custom error code,
- replaces GFP_ATOMIC by GFP_KERNEL in usb_alloc_coherent() in ttusb_dec_init_usb()
  as soon as all other memory allocation done with GFP_KERNEL;
- refactors ttusb_dec_boot_dsp() in an equivalent way except for returning 0
  instead of 1 if ttusb_dec_boot_dsp() succeed in (!mode) branch.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Changeset 9e8da9e8 added a parameter to specify the frequency
divisor, used by the driver. However, not all places are passing
this parameter. So, preserve the previous default, to avoid breaking
the existing drivers.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

[media] media: dvb-frontends: ts2020: Added in a option for frequency divider value for s600 devices

When the tuner part of the ds3000 driver was split to share code with the m88rs2000 driver, the ts2020 driver used
the frequency divider value from the m88rs2000 driver.  However the ds3000 driver requires a different value, and this
resulted in some frequecies being invisible to the tuner.  This patch adds back in the value needed for the ds3000 driver
and configured as an option in the dw2102 frontend driver.
It may also apply to su3000 devices, which use the same ds3000 driver, but for now it is only applied to the s660 device.
Signed-off-by: NJohn Horan <knasher@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Thanks-to: Joe Perches <joe@perches.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Make sure that a format string cannot accidentally
leak into the printk buffer.
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

SIZEOF_ARRAY is not used (anymore). Besides, ARRAY_SIZE, defined in
include/linux/kernel.h, should be used rather than explicitly coding some
variant of it.
Signed-off-by: NChristoph Jaeger <christophjaeger@linux.com>
Reviewed-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Reading firmware status register to detect whether firmware is
running or not didn't work 100% reliably. That register was
likely set by firmware itself which means it could not contain
reasonable values until firmware is up and running. Usually it
just worked as some garbage value was returned accidentally but it
appears that in some cases returned garbage value was 0x00 which
was considered "firmware is up and running" by the driver and
firmware loading was skipped leaving device to non-working state.
Fix problem by removing unreliable check and let the driver keep
count whether firmware is loaded or not.
Signed-off-by: NAndreas Matthies <a.matthies@gmx.net>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The variable vco_select is only assigned the values true and false.
Change its type to bool.
The simplified semantic patch that find this problem is as
follows (http://coccinelle.lip6.fr/):
@exists@
type T;
identifier b;
@@
- T
+ bool
  b = ...;
  ... when any
  b = \(true\|false\)
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Acked-by: NHans-Frieder Vogt <hfvogt@gmx.net>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Complete() will be run with interrupt enabled, so change to
spin_lock_irqsave().
These functions may be called inside URB->complete(), so use
spin_lock_irqsave().
Signed-off-by: NMing Lei <ming.lei@canonical.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

drivers/media/usb/gspca/stk1135.c:615:6: warning: no previous prototype for 'stk1135_try_fmt' [-Wmissing-prototypes]
 void stk1135_try_fmt(struct gspca_dev *gspca_dev, struct v4l2_format *fmt)
      ^
drivers/media/usb/gspca/stk1135.c:627:5: warning: no previous prototype for 'stk1135_enum_framesizes' [-Wmissing-prototypes]
 int stk1135_enum_framesizes(struct gspca_dev *gspca_dev,
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add debug print so it's easier to find any errors resulting from
the planes' configuration checks added in commit 8023ed09
"videobuf2-core: Verify planes lengths for output buffers".
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

__qbuf_userptr checks whether provided buffer is large enough, and
it returns error without any log.
Signed-off-by: NSeung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: NHeejin Woo <heejin.woo@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Replace the private struct vb2_dma_sg_desc with the struct sg_table so
we can benefit from all the helping functions in lib/scatterlist.c for
things like allocating the sg or compacting the descriptor.
marvel-ccic and solo6x10 drivers, that use this API have been updated.
Acked-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: NAndre Heider <a.heider@gmail.com>
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
[s.nawrocki@samsung.com: minor corrections of the changelog]
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Most DMA engines have limitations regarding the number of DMA segments
(sg-buffers) that they can handle. Videobuffers can easily spread
through hundreds of pages.
In the previous aproach, the pages were allocated individually, this
could led to the creation houndreds of dma segments (sg-buffers) that
could not be handled by some DMA engines.
This patch tries to minimize the number of DMA segments by using
alloc_pages. In the worst case it will behave as before, but most
of the times it will reduce the number of dma segments
Acked-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: NAndre Heider <a.heider@gmail.com>
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

struct v4_file_operations defines the data param as
const char __user *data but on vb2 is defined as
char __user *data.
This patch fixes the warnings produced by this. ie:
drivers/qtec/qtec_xform.c:817:2: warning: initialization from
incompatible pointer type [enabled by default]
drivers/qtec/qtec_xform.c:817:2: warning: (near initialization for
		‘qtec_xform_v4l_fops.write’) [enabled by default]
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Instead of passing each byte through stack let's use %*ph specifier to do this
job better.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add variable resolution support to Syntek STK1135 subdriver.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add variable resolution support to gspca by allowing subdrivers to
specify try_fmt and enum_framesizes functions.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Store complete current mode (struct v4l2_pix_format) in struct gspca_dev
instead of separate pixfmt, width and height parameters.
This is a preparation for variable resolution support.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>