When a device with an isochronous endpoint is behind a hub plugged into
the Intel Panther Point xHCI host controller, and the driver submits
multiple frames per URB, the xHCI driver will set the Block Event
Interrupt (BEI) flag on all but the last TD for the URB.  This causes
the host controller to place an event on the event ring, but not send an
interrupt.  When the last TD for the URB completes, BEI is cleared, and
we get an interrupt for the whole URB.

However, under a Panther Point xHCI host controller, if the parent hub
is unplugged when one or more events from transfers with BEI set are on
the event ring, a port status change event is placed on the event ring,
but no interrupt is generated.  This means URBs stop completing, and the
USB device disconnect is not noticed.  Something like a USB headset will
cause mplayer to hang when the device is disconnected.

If another transfer is sent (such as running `sudo lsusb -v`), the next
transfer event seems to "unstick" the event ring, the xHCI driver gets
an interrupt, and the disconnect is reported to the USB core.

The fix is not to use the BEI flag under the Panther Point xHCI host.
This will impact power consumption and system responsiveness, because
the xHCI driver will receive an interrupt for every frame in all
isochronous URBs instead of once per URB.

Intel chipset developers confirm that this bug will be hit if the BEI
flag is used on any endpoint, not just ones that are behind a hub.

This patch should be backported to kernels as old as 3.0, that contain
the commit 69e848c2 "Intel xhci: Support
EHCI/xHCI port switching."
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

In 71c731a2: usb: host: xhci: Fix Compliance Mode on SN65LVPE502CP Hardware
when extracting DMI strings (vendor or product_name) to mark them as quirk
we may get NULL pointer in case of non-x86 systems which won't define
CONFIG_DMI. Hence susbsequent strstr() calls crash while driver probing.

So, returning 'false' here in case we get a NULL vendor or product_name.

This is tested with ARM (exynos) system.

This patch should be backported to stable kernels as old as 3.6, that
contain the commit 71c731a2 "usb: host:
xhci: Fix Compliance Mode on SN65LVPE502CP Hardware"
Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: NSebastian Gottschall (DD-WRT) <s.gottschall@dd-wrt.com>
Cc: stable@vger.kernel.org

The Intel XHCI specification says that after clearing the run/stop bit
the controller may take up to 16ms to halt. We've seen a device take
14ms, which with the current timeout of 10ms causes the kernel to
abort the suspend. Increasing the timeout to the recommended value
fixes the problem.

This patch should be backported to kernels as old as 2.6.37, that
contain the commit 5535b1d5 "USB: xHCI:
PCI power management implementation".
Signed-off-by: NMichael Spang <spang@chromium.org>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

Fixes the following NULL pointer dereference:
[    7.740000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    7.810000] Unable to handle kernel NULL pointer dereference at virtual address 00000028
[    7.810000] pgd = c3a38000
[    7.810000] [00000028] *pgd=23a8c831, *pte=00000000, *ppte=00000000
[    7.810000] Internal error: Oops: 17 [#1] PREEMPT ARM
[    7.810000] Modules linked in: ohci_hcd(+) regmap_i2c snd_pcm usbcore snd_page_alloc at91_cf snd_timer pcmcia_rsrc snd soundcore gpio_keys regmap_spi pcmcia_core usb_common nls_base
[    7.810000] CPU: 0    Not tainted  (3.6.0-rc6-mpa+ #264)
[    7.810000] PC is at __gpio_to_irq+0x18/0x40
[    7.810000] LR is at ohci_hcd_at91_overcurrent_irq+0x24/0xb4 [ohci_hcd]
[    7.810000] pc : [<c01392d4>]    lr : [<bf08f694>]    psr: 40000093
[    7.810000] sp : c3a11c40  ip : c3a11c50  fp : c3a11c4c
[    7.810000] r10: 00000000  r9 : c02dcd6e  r8 : fefff400
[    7.810000] r7 : 00000000  r6 : c02cc928  r5 : 00000030  r4 : c02dd168
[    7.810000] r3 : c02e7350  r2 : ffffffea  r1 : c02cc928  r0 : 00000000
[    7.810000] Flags: nZcv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment user
[    7.810000] Control: c000717f  Table: 23a38000  DAC: 00000015
[    7.810000] Process modprobe (pid: 285, stack limit = 0xc3a10270)
[    7.810000] Stack: (0xc3a11c40 to 0xc3a12000)
[    7.810000] 1c40: c3a11c6c c3a11c50 bf08f694 c01392cc c3a11c84 c2c38b00 c3806900 00000030
[    7.810000] 1c60: c3a11ca4 c3a11c70 c0051264 bf08f680 c3a11cac c3a11c80 c003e764 c3806900
[    7.810000] 1c80: c2c38b00 c02cb05c c02cb000 fefff400 c3806930 c3a11cf4 c3a11cbc c3a11ca8
[    7.810000] 1ca0: c005142c c005123c c3806900 c3805a00 c3a11cd4 c3a11cc0 c0053f24 c00513e4
[    7.810000] 1cc0: c3a11cf4 00000030 c3a11cec c3a11cd8 c005120c c0053e88 00000000 00000000
[    7.810000] 1ce0: c3a11d1c c3a11cf0 c00124d0 c00511e0 01400000 00000001 00000012 00000000
[    7.810000] 1d00: ffffffff c3a11d94 00000030 00000000 c3a11d34 c3a11d20 c005120c c0012438
[    7.810000] 1d20: c001dac4 00000012 c3a11d4c c3a11d38 c0009b08 c00511e0 c00523fc 60000013
[    7.810000] 1d40: c3a11d5c c3a11d50 c0008510 c0009ab4 c3a11ddc c3a11d60 c0008eb4 c00084f0
[    7.810000] 1d60: 00000000 00000030 00000000 00000080 60000013 bf08f670 c3806900 c2c38b00
[    7.810000] 1d80: 00000030 c3806930 00000000 c3a11ddc c3a11d88 c3a11da8 c0054190 c00523fc
[    7.810000] 1da0: 60000013 ffffffff c3a11dec c3a11db8 00000000 c2c38b00 bf08f670 c3806900
[    7.810000] 1dc0: 00000000 00000080 c02cc928 00000030 c3a11e0c c3a11de0 c0052764 c00520d8
[    7.810000] 1de0: c3a11dfc 00000000 00000000 00000002 bf090f61 00000004 c02cc930 c02cc928
[    7.810000] 1e00: c3a11e4c c3a11e10 bf090978 c005269c bf090f61 c02cc928 bf093000 c02dd170
[    7.810000] 1e20: c3a11e3c c02cc930 c02cc930 bf0911d0 bf0911d0 bf093000 c3a10000 00000000
[    7.810000] 1e40: c3a11e5c c3a11e50 c0155b7c bf090808 c3a11e7c c3a11e60 c0154690 c0155b6c
[    7.810000] 1e60: c02cc930 c02cc964 bf0911d0 c3a11ea0 c3a11e9c c3a11e80 c015484c c01545e8
[    7.810000] 1e80: 00000000 00000000 c01547e4 bf0911d0 c3a11ec4 c3a11ea0 c0152e58 c01547f4
[    7.810000] 1ea0: c381b88c c384ab10 c2c10540 bf0911d0 00000000 c02d7518 c3a11ed4 c3a11ec8
[    7.810000] 1ec0: c01544c0 c0152e0c c3a11efc c3a11ed8 c01536cc c01544b0 bf091075 c3a11ee8
[    7.810000] 1ee0: bf049af0 bf09120c bf0911d0 00000000 c3a11f1c c3a11f00 c0154e9c c0153628
[    7.810000] 1f00: bf049af0 bf09120c 000ae190 00000000 c3a11f2c c3a11f20 c0155f58 c0154e04
[    7.810000] 1f20: c3a11f44 c3a11f30 bf093054 c0155f1c 00000000 00006a4f c3a11f7c c3a11f48
[    7.810000] 1f40: c0008638 bf093010 bf09120c 000ae190 00000000 c00093c4 00006a4f bf09120c
[    7.810000] 1f60: 000ae190 00000000 c00093c4 00000000 c3a11fa4 c3a11f80 c004fdc4 c000859c
[    7.810000] 1f80: c3a11fa4 000ae190 00006a4f 00016eb8 000ad018 00000080 00000000 c3a11fa8
[    7.810000] 1fa0: c0009260 c004fd58 00006a4f 00016eb8 000ae190 00006a4f 000ae100 00000000
[    7.810000] 1fc0: 00006a4f 00016eb8 000ad018 00000080 000adba0 000ad208 00000000 000ad3d8
[    7.810000] 1fe0: beaf7ae8 beaf7ad8 000172b8 b6e4e940 20000010 000ae190 00000000 00000000
[    7.810000] Backtrace:
[    7.810000] [<c01392bc>] (__gpio_to_irq+0x0/0x40) from [<bf08f694>] (ohci_hcd_at91_overcurrent_irq+0x24/0xb4 [ohci_hcd])
[    7.810000] [<bf08f670>] (ohci_hcd_at91_overcurrent_irq+0x0/0xb4 [ohci_hcd]) from [<c0051264>] (handle_irq_event_percpu+0x38/0x1a8)
[    7.810000]  r6:00000030 r5:c3806900 r4:c2c38b00
[    7.810000] [<c005122c>] (handle_irq_event_percpu+0x0/0x1a8) from [<c005142c>] (handle_irq_event+0x58/0x7c)
[    7.810000] [<c00513d4>] (handle_irq_event+0x0/0x7c) from [<c0053f24>] (handle_simple_irq+0xac/0xd8)
[    7.810000]  r5:c3805a00 r4:c3806900
[    7.810000] [<c0053e78>] (handle_simple_irq+0x0/0xd8) from [<c005120c>] (generic_handle_irq+0x3c/0x48)
[    7.810000]  r4:00000030
[    7.810000] [<c00511d0>] (generic_handle_irq+0x0/0x48) from [<c00124d0>] (gpio_irq_handler+0xa8/0xfc)
[    7.810000]  r4:00000000
[    7.810000] [<c0012428>] (gpio_irq_handler+0x0/0xfc) from [<c005120c>] (generic_handle_irq+0x3c/0x48)
[    7.810000] [<c00511d0>] (generic_handle_irq+0x0/0x48) from [<c0009b08>] (handle_IRQ+0x64/0x88)
[    7.810000]  r4:00000012
[    7.810000] [<c0009aa4>] (handle_IRQ+0x0/0x88) from [<c0008510>] (at91_aic_handle_irq+0x30/0x38)
[    7.810000]  r5:60000013 r4:c00523fc
[    7.810000] [<c00084e0>] (at91_aic_handle_irq+0x0/0x38) from [<c0008eb4>] (__irq_svc+0x34/0x60)
[    7.810000] Exception stack(0xc3a11d60 to 0xc3a11da8)
[    7.810000] 1d60: 00000000 00000030 00000000 00000080 60000013 bf08f670 c3806900 c2c38b00
[    7.810000] 1d80: 00000030 c3806930 00000000 c3a11ddc c3a11d88 c3a11da8 c0054190 c00523fc
[    7.810000] 1da0: 60000013 ffffffff
[    7.810000] [<c00520c8>] (__setup_irq+0x0/0x458) from [<c0052764>] (request_threaded_irq+0xd8/0x134)
[    7.810000] [<c005268c>] (request_threaded_irq+0x0/0x134) from [<bf090978>] (ohci_hcd_at91_drv_probe+0x180/0x41c [ohci_hcd])
[    7.810000] [<bf0907f8>] (ohci_hcd_at91_drv_probe+0x0/0x41c [ohci_hcd]) from [<c0155b7c>] (platform_drv_probe+0x20/0x24)
[    7.810000] [<c0155b5c>] (platform_drv_probe+0x0/0x24) from [<c0154690>] (driver_probe_device+0xb8/0x20c)
[    7.810000] [<c01545d8>] (driver_probe_device+0x0/0x20c) from [<c015484c>] (__driver_attach+0x68/0x88)
[    7.810000]  r7:c3a11ea0 r6:bf0911d0 r5:c02cc964 r4:c02cc930
[    7.810000] [<c01547e4>] (__driver_attach+0x0/0x88) from [<c0152e58>] (bus_for_each_dev+0x5c/0x9c)
[    7.810000]  r6:bf0911d0 r5:c01547e4 r4:00000000
[    7.810000] [<c0152dfc>] (bus_for_each_dev+0x0/0x9c) from [<c01544c0>] (driver_attach+0x20/0x28)
[    7.810000]  r7:c02d7518 r6:00000000 r5:bf0911d0 r4:c2c10540
[    7.810000] [<c01544a0>] (driver_attach+0x0/0x28) from [<c01536cc>] (bus_add_driver+0xb4/0x22c)
[    7.810000] [<c0153618>] (bus_add_driver+0x0/0x22c) from [<c0154e9c>] (driver_register+0xa8/0x144)
[    7.810000]  r7:00000000 r6:bf0911d0 r5:bf09120c r4:bf049af0
[    7.810000] [<c0154df4>] (driver_register+0x0/0x144) from [<c0155f58>] (platform_driver_register+0x4c/0x60)
[    7.810000]  r7:00000000 r6:000ae190 r5:bf09120c r4:bf049af0
[    7.810000] [<c0155f0c>] (platform_driver_register+0x0/0x60) from [<bf093054>] (ohci_hcd_mod_init+0x54/0x8c [ohci_hcd])
[    7.810000] [<bf093000>] (ohci_hcd_mod_init+0x0/0x8c [ohci_hcd]) from [<c0008638>] (do_one_initcall+0xac/0x174)
[    7.810000]  r4:00006a4f
[    7.810000] [<c000858c>] (do_one_initcall+0x0/0x174) from [<c004fdc4>] (sys_init_module+0x7c/0x1a0)
[    7.810000] [<c004fd48>] (sys_init_module+0x0/0x1a0) from [<c0009260>] (ret_fast_syscall+0x0/0x2c)
[    7.810000]  r7:00000080 r6:000ad018 r5:00016eb8 r4:00006a4f
[    7.810000] Code: e24cb004 e59f3028 e1a02000 e7930180 (e5903028)
[    7.810000] ---[ end trace 85aa37ed128143b5 ]---
[    7.810000] Kernel panic - not syncing: Fatal exception in interrupt

Commit 6fffb77c (USB: ohci-at91: fix PIO handling in relation with number of
ports) started setting unused pins to EINVAL. But this exposed a bug in the
ohci_hcd_at91_overcurrent_irq function where the gpio was used without being
checked to see if it is valid.

This patches fixed the issue by adding the gpio valid check.
Signed-off-by: NJoachim Eastwood <joachim.eastwood@jotron.com>
Cc: stable <stable@vger.kernel.org> # [3.4+] whereever 6fffb77c went
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add support for USB controller version 2.4
Signed-off-by: NRamneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1606) converts two warning messages in the ehci-hcd
driver to debug messages, and adds a little extra information to each.

The log messages occur when an EHCI controller takes too long (more
than 20 ms) to turn its async or periodic schedule on or off.  If this
happens at all, it's liable to happen quite often and there's no point
spamming the system log with these warnings.  Furthermore, there's
nothing much we can do about it when the problem happens.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: NThomas Voegtle <tv@lio96.de>
Cc: stable <stable@vger.kernel.org> # [3.6]
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1605) removes a useless test from the EHCI debugfs
code.  There's no point checking whether p.qh is non-NULL; we already
know it is and in any case it gets dereferenced aerlier in the
function.

The useless test was identified by smatch.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Just like for the in-tree early console debug port driver, the
hypervisor - when using a debug port based console - also needs to be
told about controller resets, so it can suppress using and then
re-initialize the debug port accordingly.

Other than the in-tree driver, the hypervisor driver actually cares
about doing this only for the device where the debug is port actually
in use, i.e. it needs to be told the coordinates of the device being
reset (quite obviously, leveraging the addition done for that would
likely benefit the in-tree driver too).
Signed-off-by: NJan Beulich <jbeulich@suse.com>
Acked-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

As discussed at the kernel summit this year, CONFIG_EXPERIMENTAL means
nothing, so let's get rid of it.
Acked-by: NFelipe Balbi <balbi@ti.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: David Herrmann <dh.herrmann@googlemail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Neil Zhang <zhangwm@marvell.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

removes unnecessary semicolon

Found by Coccinelle: http://coccinelle.lip6.fr/Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

removes unnecessary semicolon

Found by Coccinelle: http://coccinelle.lip6.fr/Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

The comment is a quote of Alan Stern and reflects the data structure
better than the the initial comment.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

drivers/usb/host/xhci.c:1826:14: warning: symbol 'xhci_get_block_size' was not declared. Should it be static?
drivers/usb/host/xhci.c:1844:14: warning: symbol 'xhci_get_largest_overhead' was not declared. Should it be static?
drivers/usb/host/xhci-ring.c:2304:36: warning: context imbalance in 'handle_tx_event' - unexpected unlock
drivers/usb/host/xhci-hub.c:425:6: warning: symbol 'xhci_set_remote_wake_mask' was not declared. Should it be static?
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

According to xHCI spec section 4.6.1.1 and section 4.6.1.2,
after aborting a command on the command ring, xHC will
generate a command completion event with its completion
code set to Command Ring Stopped at least. If a command is
currently executing at the time of aborting a command, xHC
also generate a command completion event with its completion
code set to Command Abort. When the command ring is stopped,
software may remove, add, or rearrage Command Descriptors.

To cancel a command, software will initialize a command
descriptor for the cancel command, and add it into a
cancel_cmd_list of xhci. When the command ring is stopped,
software will find the command trbs described by command
descriptors in cancel_cmd_list and modify it to No Op
command. If software can't find the matched trbs, we can
think it had been finished.

This patch should be backported to kernels as old as 3.0, that contain
the commit 7ed603ec "xhci: Add an
assertion to check for virt_dev=0 bug." That commit papers over a NULL
pointer dereference, and this patch fixes the underlying issue that
caused the NULL pointer dereference.
Signed-off-by: NElric Fu <elricfu1@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: NMiroslav Sabljic <miroslav.sabljic@avl.com>
Cc: stable@vger.kernel.org

The patch is used to cancel command when the command isn't
acknowledged and a timeout occurs.

This patch should be backported to kernels as old as 3.0, that contain
the commit 7ed603ec "xhci: Add an
assertion to check for virt_dev=0 bug." That commit papers over a NULL
pointer dereference, and this patch fixes the underlying issue that
caused the NULL pointer dereference.
Signed-off-by: NElric Fu <elricfu1@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: NMiroslav Sabljic <miroslav.sabljic@avl.com>
Cc: stable@vger.kernel.org

Software have to abort command ring and cancel command
when a command is failed or hang. Otherwise, the command
ring will hang up and can't handle the others. An example
of a command that may hang is the Address Device Command,
because waiting for a SET_ADDRESS request to be acknowledged
by a USB device is outside of the xHC's ability to control.

To cancel a command, software will initialize a command
descriptor for the cancel command, and add it into a
cancel_cmd_list of xhci.

Sarah: Fixed missing newline on "Have the command ring been stopped?"
debugging statement.

This patch should be backported to kernels as old as 3.0, that contain
the commit 7ed603ec "xhci: Add an
assertion to check for virt_dev=0 bug." That commit papers over a NULL
pointer dereference, and this patch fixes the underlying issue that
caused the NULL pointer dereference.
Signed-off-by: NElric Fu <elricfu1@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: NMiroslav Sabljic <miroslav.sabljic@avl.com>
Cc: stable@vger.kernel.org

Adding cmd_ring_state for command ring. It helps to verify
the current command ring state for controlling the command
ring operations.

This patch should be backported to kernels as old as 3.0.  The commit
7ed603ec "xhci: Add an assertion to
check for virt_dev=0 bug." papers over the NULL pointer dereference that
I now believe is related to a timed out Set Address command.  This (and
the four patches that follow it) contain the real fix that also allows
VIA USB 3.0 hubs to consistently re-enumerate during the plug/unplug
stress tests.
Signed-off-by: NElric Fu <elricfu1@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: NMiroslav Sabljic <miroslav.sabljic@avl.com>
Cc: stable@vger.kernel.org

Because the IRQF_DISABLED as the flag is now a NOOP and has been
deprecated and in hardirq context the interrupt is disabled.

so in usb/host code:
Removing the usage of flag IRQF_DISABLED;
Removing the calling local_irq save/restore actions in irq
handler usb_hcd_irq();
Signed-off-by: Nliu chuansheng <chuansheng.liu@intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There is a possibility of QH overlay region having reference to a stale
qTD pointer during unlink.

Consider an endpoint having two pending qTD before unlink process begins.
The endpoint's QH queue looks like this.

qTD1 --> qTD2 --> Dummy

To unlink qTD2, QH is removed from asynchronous list and Asynchronous
Advance Doorbell is programmed.  The qTD1's next qTD pointer is set to
qTD2'2 next qTD pointer and qTD2 is retired upon controller's doorbell
interrupt.  If QH's current qTD pointer points to qTD1, transfer overlay
region still have reference to qTD2. But qtD2 is just unlinked and freed.
This may cause EHCI system error.  Fix this by updating qTD next pointer
in QH overlay region with the qTD next pointer of the current qTD.
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Upcoming Intel systems will have an ACPI method to control whether a USB
port can be completely powered off.  The implication of powering off a
USB port is that the device and host sees a physical disconnect, and
subsequent port connections and remote wakeups will be lost.

Add a new function, usb_acpi_power_manageable(), that can be used to
find whether the usb port has ACPI power resources that can be used to
power on and off the port on these machines. Also add a new function
called usb_acpi_set_power_state() that controls the port power via these
ACPI methods.

When the USB core calls into the xHCI hub driver to power off a port,
check whether the port can be completely powered off via this new ACPI
mechanism.  If so, call into these new ACPI methods.  Also use the ACPI
methods when the USB core asks to power on a port.
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch makes the xHCI roothub code handle the clear PORT_POWER
feature request.  Setting port power is already handled.
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The usb_device structure contains an array of usb_device "children".
This array is only valid if the usb_device is a hub, so it makes no
sense to store it there.  Instead, store the usb_device child
in its parent usb_port structure.

Since usb_port is an internal USB core structure, add a new function to
get the USB device child, usb_hub_find_child().  Add a new macro,
usb_hub_get_each_child(), to iterate over all the children attached to a
particular USB hub.

Remove the printing the USB children array pointer from the usb-ip
driver, since it's really not necessary.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If the number of ports present on the SoC/board is not the maximum
and that the platform data is not filled with all data, there is
an easy way to mess the PIO setup for this interface.
This quick fix addresses mis-configuration in USB host platform data
that is common in at91 boards since commit 0ee6d1ee (USB: ohci-at91:
change maximum number of ports) that did not modified the associatd
board files.
Reported-by: NKlaus Falkner <klaus.falkner@solectrix.de>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: Stable <stable@vger.kernel.org> [3.4+]
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Using list_move_tail() instead of list_del() + list_add_tail().

spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Change the call to PTR_ERR to access the value just tested by IS_ERR.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression e,e1;
@@

(
if (IS_ERR(e)) { ... PTR_ERR(e) ... }
|
if (IS_ERR(e=e1)) { ... PTR_ERR(e) ... }
|
*if (IS_ERR(e))
 { ...
*  PTR_ERR(e1)
   ... }
)
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

With "select USB_ISP1301 ...", it could happen that I2C isn't selected although
USB_ISP1301 depends on it. Fixing with "depends on ..." and emulating the
condition via "|| !()".
Signed-off-by: NRoland Stigge <stigge@antcom.de>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

when missing USB PHY clock, kernel booting up will hang during USB
initialization. We should check USBGP[PHY_CLK_VALID] bit to avoid
CPU hanging in this case.
Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NPeter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

For non PCI-based stacks, this function call
usb_disable_xhci_ports(to_pci_dev(hcd->self.controller));
made from xhci_shutdown is not applicable.

Ideally, we wouldn't have any PCI-specific code on
a generic driver such as the xHCI stack, but it looks
like we should just stub usb_disable_xhci_ports() out
for non-PCI devices.

[ balbi@ti.com: slight improvement to commit log ]

This patch should be backported to kernels as old as 3.0, since the
commit it fixes (e95829f4 "xhci: Switch
PPT ports to EHCI on shutdown.") was marked for stable.

Signed-off-by: Moiz Sonasath<m-sonasath@ti.com>
Signed-off-by: NRuchika Kharwar <ruchika@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

Use the ioremap_nocache variant of the ioremap API in
order to make sure our memory will be marked uncachable.

This patch should be backported to kernels as old as 3.4, that contain
the commit 3429e91a "usb: host: xhci:
add platform driver support".
Signed-off-by: NRuchika Kharwar <ruchika@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

This patch is intended to work around a known issue on the
SN65LVPE502CP USB3.0 re-driver that can delay the negotiation
between a device and the host past the usual handshake timeout.

If that happens on the first insertion, the host controller
port will enter in Compliance Mode and NO port status event will
be generated (as per xHCI Spec) making impossible to detect this
event by software. The port will remain in compliance mode until
a warm reset is applied to it.

As a result of this, the port will seem "dead" to the user and no
device connections or disconnections will be detected.

For solving this, the patch creates a timer which polls every 2
seconds the link state of each host controller's port (this
by reading the PORTSC register) and recovers the port by issuing a
Warm reset every time Compliance mode is detected.

If a xHC USB3.0 port has previously entered to U0, the compliance
mode issue will NOT occur only until system resumes from
sleep/hibernate, therefore, the compliance mode timer is stopped
when all xHC USB 3.0 ports have entered U0. The timer is initialized
again after each system resume.

Since the issue is being caused by a piece of hardware, the timer
will be enabled ONLY on those systems that have the SN65LVPE502CP
installed (this patch uses DMI strings for detecting those systems)
therefore making this patch to act as a quirk (XHCI_COMP_MODE_QUIRK
has been added to the xhci stack).

This patch applies for these systems:
Vendor: Hewlett-Packard. System Models: Z420, Z620 and Z820.

This patch should be backported to kernels as old as 3.2, as that was
the first kernel to support warm reset.  The kernels will need to
contain both commit 10d674a8 "USB: When
hot reset for USB3 fails, try warm reset" and commit
8bea2bd3 "usb: Add support for root hub
port status CAS".  The first patch add warm reset support, and the
second patch modifies the USB core to issue a warm reset when the port
is in compliance mode.
Signed-off-by: NAlexis R. Cortes <alexis.cortes@ti.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

My test platform (Intel DX79SI) boots reliably under BIOS, but frequently
crashes when booting via UEFI. I finally tracked this down to the xhci
handoff code. It seems that reads from the device occasionally just return
0xff, resulting in xhci_find_next_cap_offset generating a value that's
larger than the resource region. We then oops when attempting to read the
value. Sanity checking that value lets us avoid the crash.

I've no idea what's causing the underlying problem, and xhci still doesn't
actually *work* even with this, but the machine at least boots which will
probably make further debugging easier.

This should be backported to kernels as old as 2.6.31, that contain the
commit 66d4eadd "USB: xhci: BIOS handoff
and HW initialization."
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

The intent was to test whether the flag was set.

This patch should be backported to stable kernels as old as 3.0, since
it fixes a bug in commit e95829f4 "xhci:
Switch PPT ports to EHCI on shutdown.", which was marked for stable.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

As part of this patch:
	1. Moved existing tegra phy driver to drivers/USB directory.
	2. Added standard USB phy driver APIs to tegra phy driver.
Signed-off-by: NVenu Byravarasu <vbyravarasu@nvidia.com>
Tested-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

With a previous patch to enable the EHCI/XHCI port switching, it switches
all the available ports.

The assumption is not correct because the BIOS may expect some ports
not switchable by the OS.

There are two more registers that contains the information of the switchable
and non-switchable ports.

This patch adds the checking code for the two register so that only the
switchable ports are altered.

This patch should be backported to kernels as old as 3.0, that contain
commit ID 69e848c2 "Intel xhci: Support
EHCI/xHCI port switching."
Signed-off-by: NKeng-Yu Lin <kengyu@canonical.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

On Intel Panther Point chipset USB 3.0 devices show up as
high-speed devices on powerup, but after an s3 cycle they are
correctly recognized as SuperSpeed. At powerup switch the port
to xHCI so that USB 3.0 devices are correctly recognized.

BugLink: http://bugs.launchpad.net/bugs/1000424

This patch should be backported to kernels as old as 3.0, that contain
commit ID 69e848c2 "Intel xhci: Support
EHCI/xHCI port switching."
Signed-off-by: NManoj Iyer <manoj.iyer@canonical.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

Add support for a generic non-pci UHCI companion controller.
Existing board files for arch-vt8500 updated to include UHCI
support.
Signed-off-by: NTony Prisk <linux@prisktech.co.nz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NTony Prisk <linux@prisktech.co.nz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Convert a possibly 0 error return code to a negative one, as returned
elsewhere in the function.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@

(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
    when != ret = e3
*if (x == NULL || ...)
{
  ... when != ret = e4
*  return ret;
}
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Convert a possibly 0 error return code to a negative one, as returned
elsewhere in the function.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@

(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
    when != ret = e3
*if (x == NULL || ...)
{
  ... when != ret = e4
*  return ret;
}
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>