Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

M66592 has the pin of WR0 and WR1. So, if one write-pin of CPU
connects to the pins, we have to change the setting of FIFOSEL
register in the controller. If we don't change the setting,
the controller cannot send the data of odd length.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch adds SuperSpeed descriptors to the
g_zero gadget.

The SuperSpeed descriptors were added both for
f_soursesink and f_loopback function drivers.
Signed-off-by: NTatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: NAmit Blay <ablay@codeaurora.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add SuperSpeed descriptors to the Network USB
function drivers.

This has been lightly tested using a Linux host.
I was able to ssh from device to host and host to
device, no obvious problems seen.
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The USB high speed device must support the TEST_MODE, but the driver
didn't support it. When we sent the SET_FEATURE for TEST_MODE to
the driver, the request was successful, but the module didn't enter
the TEST_MODE.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The USB high speed device must support the TEST_MODE, but the driver
didn't support it. When we sent the SET_FEATURE for TEST_MODE to
the driver, the request was successful, but the module didn't enter
the TEST_MODE.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

BUSWAIT is a 4-bit-wide value that controls the number of access waits
from the CPU to on-chip USB module. b'0000 inserts 0 wait (2 access
cycles) and b'1111 inserts 15 waits (17 access cycles, hardware
initial value), respectively.

BUSWAIT value depends on peripheral clock frequency supplied to on-chip
of each CPU, hence should be configurable through platform data.

Note that this patch assumes that b'0000 (0 wait, 2 access cycles) is
rerely used and considered as invalid. If valid 'buswait' data is not
provided by platform, initial b'1111 (15 waits, 17 access cycles) will
be applied as a safe default.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When we run rmmod a gadget driver, the driver will call
disable_controller(). Then, because the bit of USBE in SYSCFG0 was
cleared in on_chip=1 mode, we could not connect the usb when we run
insmod a gadget driver next time.
This patch also cleans up probe() and ->stop() about unnecessary
init_controller().
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Restoring the missing INDEX register value in musb_restore_context().
Without this suspend resume functionality is broken with offmode
enabled.

Cc: stable@kernel.org
Acked-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Both fusb300 and langwell udcs seem to only
work with 32-bit address space.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

- remove pointer u32 abuse in fusb300_fill_idma_prdtbl().
  It is assigned the dma_addr to a pointer and then back.
  Poor families may have to recycle variables but we don't

- don't free req.buf in error case. We don't do it in the
  ok case so it is probably wrong to do it in error case.

- return in error case. There is no reason to continue
  without data and performing ops on an invalid pointer.

- The if (d) statement is bogus since an invalid DMA pointer
  is ~0 on some architecutres. And since we return for the
  invalid case we don't need it.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Fix the following compile warning:

| usb/gadget/ci13xxx_udc.c: In function 'show_registers':
| usb/gadget/ci13xxx_udc.c:1242:1: warning: the frame size of 2064 bytes is larger than 1024 bytes
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch fixes the following compile warnings:

drivers/usb/gadget/net2272.c: In function ‘net2272_kick_dma’:
drivers/usb/gadget/net2272.c:740:2: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 6 has type ‘dma_addr_t’ [-Wformat]
drivers/usb/gadget/net2272.c: In function ‘net2272_queue’:
drivers/usb/gadget/net2272.c:859:2: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 8 has type ‘dma_addr_t’ [-Wformat]
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch fixes the following compile warnings:

drivers/usb/gadget/langwell_udc.c: In function ‘queue_dtd’:
drivers/usb/gadget/langwell_udc.c:596:2: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/usb/gadget/langwell_udc.c: In function ‘langwell_udc_probe’:
drivers/usb/gadget/langwell_udc.c:3274:2: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has type ‘size_t’ [-Wformat]
drivers/usb/gadget/langwell_udc.c:3289:2: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has type ‘size_t’ [-Wformat]
drivers/usb/gadget/langwell_udc.c: In function ‘langwell_udc_resume’:
drivers/usb/gadget/langwell_udc.c:3473:2: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has type ‘size_t’ [-Wformat]
drivers/usb/gadget/langwell_udc.c:3487:2: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has type ‘size_t’ [-Wformat]
Signed-off-by: NFelipe Balbi <balbi@ti.com>

that code has been dead forever. Since the
first commit (0fe6f1d1) the use of that code
has been commented out. Let's drop the dead
code already and fix the following compile
warning:

| drivers/usb/gadget/fusb300_udc.c: At top level:
| drivers/usb/gadget/fusb300_udc.c:771:13: warning: ‘fusb300_wrfifo’ defined but not used [-Wunused-function]
| drivers/usb/gadget/fusb300_udc.c:1027:13: warning: ‘fusb300_set_ep_bycnt’ defined but not used [-Wunused-function]
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The autosuspend function can be disabled by unchecking the Macro
CONFIG_REALTEK_AUTOPM in kernel config file, by default, this macro is
turned on.
Signed-off-by: Nedwin_rong <edwin_rong@realsil.com.cn>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove Macros wait_timeout() and wait_timeout_x().
Signed-off-by: Nedwin_rong <edwin_rong@realsil.com.cn>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Nedwin_rong <edwin_rong@realsil.com.cn>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There is a bug in Samsung's UDC driver, which is completely disabling
the USB device when a custom UDC command is used.
Following patch seems to get the right behavior (e.g. enabling pull-up
instead of disabling then Vcc is applied).
Signed-off-by: NViliam Mateicka <viliam.mateicka@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

A compilation warning was added by the patch
"usb: gadget: use config_ep_by_speed() instead of ep_choose()".
This patch fixed it.
Signed-off-by: NTatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

With this commit: cccad6d4
usb: otg: notifier: switch to atomic notifier

Following dumps are observed on attach/detach for MUSB HOST
mode and on a detach for MUSB Device mode.

BUG: sleeping function called from invalid context at kernel/mutex.c:85
where, the source is:
twl6030_usb_irq
->atomic_notifier_call_chain
 ->musb_otg_notifications
  ->twl6030_set_vbus
   ->twl_i2c_write_u8
    ->mutex_lock

This patch moves the i2c writes in set_vbus function to a
work-queue thereby avoiding I2C writes in atomic context.

Tested HOST and Device mode functionality on OMAP4460
Signed-off-by: NMoiz Sonasath <m-sonasath@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The config bind was reported success even if usb_add_function
failed. Fix the return value.
Signed-off-by: NJassi Brar <jaswinder.singh@linaro.org>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The recent commit 2edb11cb fixed req->length in the composite_setup()
function, but that will cause all g_zero tests to fail like:

root#> ./testusb -D /proc/bus/usb/002/021 -t14 -c 15000 -s 256 -v 1
unknown speed   /proc/bus/usb/002/021
/proc/bus/usb/002/021 test 14 --> 32 (Broken pipe)

We need to fix req->length in sourcesink_setup() as well to avoid this.
Signed-off-by: NBob Liu <lliubbo@gmail.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Since printk_ratelimit() shouldn't be used anymore (see comment in
include/linux/printk.h), replace it with printk_ratelimited()
Signed-off-by: NManuel Zerpies <manuel.f.zerpies@ww.stud.uni-erlangen.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Since printk_ratelimit() shouldn't be used anymore (see comment in
include/linux/printk.h), replace it with printk_ratelimited()
Signed-off-by: NManuel Zerpies <manuel.f.zerpies@ww.stud.uni-erlangen.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Since printk_ratelimit() shouldn't be used anymore (see comment in
include/linux/printk.h), replace it with printk_ratelimited()
Signed-off-by: NManuel Zerpies <manuel.f.zerpies@ww.stud.uni-erlangen.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

dev_get_drvdata() is exactly the same as
platform_get_drvdata(). Drop that useless
access to the platform device.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This was somehow forgotten.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

bind() and pull is moved to udc core, call callbacks are verified by the
upper layer.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

udc-core checks for valid callbacks so there is no need for the driver
to do so. Also "can-be-bound-once" is verified by udc-core. The pull-up
callback is called by udc-core afterwords.

[ balbi@ti.com : keep holding gadget_driver pointer for now
		 remove the stupid check for gadget_driver otherwise
		  we don't handle IRQs ]
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

udc_start() should only trigger the internal state machine and make
minimal house keeping. Before that call udc-core calls the bind()
callback and after the callback the pullup().

udc_stop() is simillar, udc-core calls pullup(), unbind() and finally
udc_stop().
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The configuration is static however we only know the speed after we have
connected with the other side.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This value is now assigned during bind(). The configuration depends on
static values assigned by dummy driver itself. So there is no need to
defer this assigment until one know the actuall speed since the
configuration is static and known early.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is only required to be done once. There is no counter part to this
in ->stop() so there is no need to re-do it next time. While here also
init the max_stream size to 0 on SS speed.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

maxpacket is set by the udc driver for ep0 very early. This value is
copied by the function gadget used later for the USB_DT_DEVICE and
USB_DT_DEVICE_QUALIFIER query. This seems to work fine so far. For USB3
we need set a different value here. In SS speed it is 2^x with x=9 and
in HS we set something <= 64. If the UDC starts in SS and continues in
HS after the cable has been plugged it will report a too small value.
There setting of this value is defered and taken automaticly from the
ep0 pointer where the UDC driver can update it according to the speed it
detected _after_ a cable has been plugged.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

now that we have the udc class, we can allow
multiple gadget controller drivers to be
compiled as modules. This will allow for
distro-like kernels for embedded devices.

With this patch, I managed to build an x86
kernel with support for many of the controllers
enabled:

CONFIG_USB_FUSB300=m
CONFIG_USB_R8A66597=m
CONFIG_USB_M66592=m
CONFIG_USB_AMD5536UDC=m
CONFIG_USB_CI13XXX_PCI=m
CONFIG_USB_NET2272=m
CONFIG_USB_NET2280=m
CONFIG_USB_GOKU=m
CONFIG_USB_LANGWELL=m
CONFIG_USB_EG20T=m

Also an ARM kernel with support for many controllers:

CONFIG_USB_FUSB300=m
CONFIG_USB_OMAP=m
CONFIG_USB_R8A66597=m
CONFIG_USB_GADGET_MUSB_HDRC=m
CONFIG_USB_M66592=m
CONFIG_USB_NET2272=m
CONFIG_USB_DUMMY_HCD=m

The next step would be to get rid of the
direct access to arch/ and mach/ directories
on some gadget controllers so that we can
build all of them without depending on their
respective ARCH_* symbols.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>