Changing occurrences of variants of PCI-X and PCIe to the PCI-SIG
terms listed in the "Trademark and Logo Usage Guidelines".
http://www.pcisig.com/developers/procedures/logos/Trademark_and_Logo_Usage_Guidelines_updated_112206.pdf

Patch is limited to drivers/pci/ and changes concern non-comment parts or
anything that might be visible to the user.
Signed-off-by: NStefan Assmann <sassmann@redhat.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Changing occurrences of variants of PCI-X and PCIe to the PCI-SIG
terms listed in the "Trademark and Logo Usage Guidelines".
http://www.pcisig.com/developers/procedures/logos/Trademark_and_Logo_Usage_Guidelines_updated_112206.pdf

Patch is limited to drivers/pci/ and changes concern comments only.
Signed-off-by: NStefan Assmann <sassmann@redhat.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The pci_cleanup_aer_correct_error_status() function has been
#if 0'd out since 2.6.25.  Time to remove the dead code.
Signed-off-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The current implementation of pci_cleanup_aer_uncorrect_error_status
only clears either fatal or non-fatal error status bits depending
on the state of the I/O channel. This implementation will then often
leave some bits set after PCI error recovery completes.  The uncleared bit
settings will then be falsely reported the next time an AER interrupt is
generated for that hierarchy. An easy way to illustrate this issue is to
use the aer-inject module to simultaneously inject both an uncorrectable
non-fatal and uncorrectable fatal error.  One of the errors will not be
cleared.

This patch resolves this issue by unconditionally clearing all bits in
the AER uncorrectable status register. All settings and corrective action
strategies are saved and determined before
pci_cleanup_aer_uncorrect_error_status is called, so this change should not
affect errory handling functionality.
Signed-off-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Remove 'port_type' field in struct pcie_port_data(), because we can
get port type information from struct pci_dev. With this change, this
patch also does followings:

 - Remove struct pcie_port_data because it no longer has any field.
 - Remove portdrv private definitions about port type (PCIE_RC_PORT,
   PCIE_SW_UPSTREAM_PORT and PCIE_SW_DOWNSTREAM_PORT), and use generic
   definitions instead.
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Changes for PCIe AER driver to use pci_is_pcie() instead of checking
pci_dev->is_pcie.
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Use pcie_cap() instead of pci_find_capability() to get PCIe capability
offset in PCIe AER driver. This avoids unnecessary search in PCI
configuration space.
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Fixed probable typo in aer_inject cleanup code resulting in a memory
leak.
Acked-by: NHuang Ying <ying.huang@intel.com>
Signed-off-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Replaced some error return values in aer_inject. Use -ENODEV when we
can't find a device and -ENOTTY when the device does not support PCIe AER.
Acked-by: NHuang Ying <ying.huang@intel.com>
Signed-off-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Add support for PCI domains (segments) to aer_inject.
Acked-by: NHuang Ying <ying.huang@intel.com>
Signed-off-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Feedback from Hidetoshi Seto and Kenji Kaneshige incorporated.  This
correctly handles PCI-X bridges, PCIe root ports and endpoints, and
prints debug messages when invalid/reserved types are found in the
HEST.  PCI devices not in domain/segment 0 are not represented in
HEST, thus will be ignored.

Today, the PCIe Advanced Error Reporting (AER) driver attaches itself
to every PCIe root port for which BIOS reports it should, via ACPI
_OSC.

However, _OSC alone is insufficient for newer BIOSes.  Part of ACPI
4.0 is the new APEI (ACPI Platform Error Interfaces) which is a way
for OS and BIOS to handshake over which errors for which components
each will handle.  One table in ACPI 4.0 is the Hardware Error Source
Table (HEST), where BIOS can define that errors for certain PCIe
devices (or all devices), should be handled by BIOS ("Firmware First
mode"), rather than be handled by the OS.

Dell PowerEdge 11G server BIOS defines Firmware First mode in HEST, so
that it may manage such errors, log them to the System Event Log, and
possibly take other actions.  The aer driver should honor this, and
not attach itself to devices noted as such.

Furthermore, Kenji Kaneshige reminded us to disallow changing the AER
registers when respecting Firmware First mode.  Platform firmware is
expected to manage these, and if changes to them are allowed, it could
break that firmware's behavior.

The HEST parsing code may be replaced in the future by a more
feature-rich implementation.  This patch provides the minimum needed
to prevent breakage until that implementation is available.
Reviewed-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Reviewed-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NMatt Domsch <Matt_Domsch@dell.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>

A bug was seen on boards using a PLX 8518 switch device which advertises
AER on each of it's transparent bridges. The AER driver was loaded for
each bridge and this driver tried to access the AER source ID register
whenever an interrupt occured on the shared PCI INTX lines. The source
ID register does not exist on non root port PCIE device's  which
advertise AER and trying to access this register causes a unsupported
request error on the bridge. Thus, when the next interrupt occurs,
another error is found and the non existent source ID register is
accessed again, and so it goes on.

The result is a spammed dmesg with unsupported request PCI express
errors on the bridge device that the AER driver is loaded against.
Reported-by: NMalcolm Crossley <malcolm.crossley2@gefanuc.com>
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: NMalcolm Crossley <malcolm.crossley2@gefanuc.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

When booting with pci=nomsi aer causes lost interrupts and
lockdep inversions.

So check if MSIs are not disabled before initializing the aer
driver.
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This patch is required not to lost error records by action invoked on
error recovery, such as slot reset etc.

Following sample (real machine + dummy record injected by aer-inject)
shows that record of 28:00.1 could not be retrieved by recovery of 28:00.0:

- Before:

pcieport-driver 0000:00:02.0: AER: Multiple Uncorrected (Non-Fatal) error received: id=2801
e1000e 0000:28:00.0: PCIE Bus Error: severity=Uncorrected (Non-Fatal), type=Transaction Layer, id=2800(Receiver ID)
e1000e 0000:28:00.0:   device [8086:1096] error status/mask=00001000/00100000
e1000e 0000:28:00.0:    [12] Poisoned TLP           (First)
e1000e 0000:28:00.0:   TLP Header: 00000000 00000001 00000002 00000003
e1000e 0000:28:00.0: broadcast error_detected message
e1000e 0000:28:00.0: broadcast slot_reset message
e1000e 0000:28:00.0: setting latency timer to 64
e1000e 0000:28:00.0: restoring config space at offset 0x1 (was 0x100547, writing 0x100147)
e1000e 0000:28:00.0: PME# disabled
e1000e 0000:28:00.0: PME# disabled
e1000e 0000:28:00.1: setting latency timer to 64
e1000e 0000:28:00.1: restoring config space at offset 0x1 (was 0x100547, writing 0x100147)
e1000e 0000:28:00.1: PME# disabled
e1000e 0000:28:00.1: PME# disabled
e1000e 0000:28:00.0: broadcast resume message
e1000e 0000:28:00.0: AER driver successfully recovered
e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX

- After:

pcieport-driver 0000:00:02.0: AER: Multiple Uncorrected (Non-Fatal) error received: id=2801
e1000e 0000:28:00.0: PCIE Bus Error: severity=Uncorrected (Non-Fatal), type=Transaction Layer, id=2800(Receiver ID)
e1000e 0000:28:00.0:   device [8086:1096] error status/mask=00001000/00100000
e1000e 0000:28:00.0:    [12] Poisoned TLP           (First)
e1000e 0000:28:00.0:   TLP Header: 00000000 00000001 00000002 00000003
e1000e 0000:28:00.1: PCIE Bus Error: severity=Uncorrected (Non-Fatal), type=Transaction Layer, id=2801(Receiver ID)
e1000e 0000:28:00.1:   device [8086:1096] error status/mask=00081000/00100000
e1000e 0000:28:00.1:    [12] Poisoned TLP           (First)
e1000e 0000:28:00.1:    [19] ECRC
e1000e 0000:28:00.1:   TLP Header: 00000000 00000001 00000002 00000003
e1000e 0000:28:00.1:   Error of this Agent(2801) is reported first
e1000e 0000:28:00.0: broadcast error_detected message
e1000e 0000:28:00.0: broadcast slot_reset message
e1000e 0000:28:00.0: setting latency timer to 64
e1000e 0000:28:00.0: restoring config space at offset 0x1 (was 0x100547, writing 0x100147)
e1000e 0000:28:00.0: PME# disabled
e1000e 0000:28:00.0: PME# disabled
e1000e 0000:28:00.1: setting latency timer to 64
e1000e 0000:28:00.1: restoring config space at offset 0x1 (was 0x100547, writing 0x100147)
e1000e 0000:28:00.1: PME# disabled
e1000e 0000:28:00.1: PME# disabled
e1000e 0000:28:00.0: broadcast resume message
e1000e 0000:28:00.0: AER driver successfully recovered
e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Use dev_printk like format.

Sample (real machine + dummy error injected by aer-inject):

- Before:

+------ PCI-Express Device Error ------+
Error Severity          : Corrected
PCIE Bus Error type     : Data Link Layer
Bad TLP                 :
Receiver ID             : 2800
VendorID=8086h, DeviceID=1096h, Bus=28h, Device=00h, Function=00h
+------ PCI-Express Device Error ------+
Error Severity          : Corrected
PCIE Bus Error type     : Data Link Layer
Bad TLP                 :
Bad DLLP                :
Receiver ID             : 2801
VendorID=8086h, DeviceID=1096h, Bus=28h, Device=00h, Function=01h
Error of this Agent(2801) is reported first

- After:

pcieport-driver 0000:00:02.0: AER: Multiple Corrected error received: id=2801
e1000e 0000:28:00.0: PCIE Bus Error: severity=Corrected, type=Data Link Layer, id=2800(Receiver ID)
e1000e 0000:28:00.0:   device [8086:1096] error status/mask=00000040/00000000
e1000e 0000:28:00.0:    [ 6] Bad TLP
e1000e 0000:28:00.1: PCIE Bus Error: severity=Corrected, type=Data Link Layer, id=2801(Receiver ID)
e1000e 0000:28:00.1:   device [8086:1096] error status/mask=000000c0/00000000
e1000e 0000:28:00.1:    [ 6] Bad TLP
e1000e 0000:28:00.1:    [ 7] Bad DLLP
e1000e 0000:28:00.1:   Error of this Agent(2801) is reported first
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Compact struct and codes.
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Cleanup.
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Multiple bits might be set in the Uncorrectable Error Status
register.  But aer_print_error_source() only report a error of
the lowest bit set in the error status register.

So print strings for all bits unmasked and set.

And check First Error Pointer to mark the error occured first.
This FEP is not valid when the corresponing bit of the Uncorrectable
Error Status register is not set, or unimplemented or undefined.
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

ERR_{,UN}CORRECTABLE_ERROR_MASK are set of error bits which linux know,
set of PCI_ERR_COR_* and PCI_ERR_UNC_* defined in linux/pci_regs.h.
This masks make aerdrv not to report errors of unknown bit, while aerdrv
have ability to report such undefined errors as "Unknown Error Bit %2d".

OTOH aerdrv_errprint does not have any check of setting in mask register.
So it could report masked wrong error by finding bit in status without
knowing that the bit is masked in the mask register.

This patch changes aerdrv to use mask state in mask register propely
instead of defined/hardcoded ERR_{,UN}CORRECTABLE_ERROR_MASK.
This change prevents aerdrv from reporting masked error, and also enable
reporting unknown errors.
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The static buffer errmsg_buff[] is used only for building error
message in fixed format, and is protected by a spinlock.

This patch removes this buffer and the spinlock.
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The flag AER_MULTI_ERROR_VALID_FLAG in info->flag does mean that the
root port receives multiple error messages.  Error messages can be
posted from different devices, so it does not mean that each reported
device has multiple errors.

If there are multiple error devices and the root port has valid error
source ID, it would be nice to report which device is the error source
reported first.
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

In case of multiple errors, struct aer_err_info would be reused among
all reported devices.  So the info->status should be initialized before
recycled.  Otherwise error of one device might be reported as the error
of another device.  Also info->flags has similar problem on reporting
TLP header.
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Definitions of MASK macros in aerdrv_errprint.c are tricky and unsafe.

For example, AER_AGENT_TRANSMITTER_MASK(_sev, _stat) does work like:
  static inline func(int _sev, int _stat)
  {
    if (_sev == AER_CORRECTABLE)
      return (_stat & (PCI_ERR_COR_REP_ROLL|PCI_ERR_COR_REP_TIMER));
    else
      return (_stat & PCI_ERR_COR_REP_ROLL);
  }
In case of else path here, for uncorrectable errors, testing bits in
_stat by PCI_ERR_COR_* does not make sense because _stat should have only
PCI_ERR_UNC_* bits originated in uncorrectable error status register.
But at this time this is safe because uncorrectable error using bit
position same to PCI_ERR_COR_REP_ROLL(= bit position 8) is not defined.
Likewise, AER_AGENT_COMPLETER_MASK is always PCI_ERR_UNC_COMP_ABORT but
it works because bit 15 of correctable error status is not defined.

It means that these MASK macros will turn to be wrong once if new error
is defined. (In fact, bit 15 of correctable is now defined in PCIe 2.1)

This patch changes these MASK macros to be more strict, not to return
PCI_ERR_COR_* bits for uncorrectable error status and vise versa.
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Add workaround macro to reduce the number of checkpatch warning:
 WARNING: printk() should include KERN_ facility level

Before:
  total: 0 errors, 10 warnings, 247 lines checked
After:
  total: 0 errors, 1 warnings, 243 lines checked
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Before:
 drivers/pci/pcie/aer/aer_inject.c
  total: 4 errors, 4 warnings, 473 lines checked
 drivers/pci/pcie/aer/aerdrv.c
  total: 5 errors, 2 warnings, 333 lines checked
 drivers/pci/pcie/aer/aerdrv.h
  total: 1 errors, 0 warnings, 139 lines checked
 drivers/pci/pcie/aer/aerdrv_core.c
  total: 4 errors, 3 warnings, 872 lines checked
 drivers/pci/pcie/aer/aerdrv_errprint.c
  total: 12 errors, 11 warnings, 248 lines checked

After:
 drivers/pci/pcie/aer/aer_inject.c
  total: 0 errors, 0 warnings, 466 lines checked
 drivers/pci/pcie/aer/aerdrv.c
  total: 0 errors, 0 warnings, 335 lines checked
 drivers/pci/pcie/aer/aerdrv.h
  total: 0 errors, 0 warnings, 139 lines checked
 drivers/pci/pcie/aer/aerdrv_core.c
  total: 0 errors, 0 warnings, 869 lines checked
 drivers/pci/pcie/aer/aerdrv_errprint.c
  total: 0 errors, 10 warnings, 247 lines checked
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Acked-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Debugging PCIE AER code can be very difficult because it is hard
to trigger various real hardware errors. This patch provide a
software based error injection tool, which can fake various PCIE
errors with a user space helper tool named "aer-inject". Which
can be gotten from:

  http://www.kernel.org/pub/linux/kernel/people/yhuang/

The patch fakes AER error by faking some PCIE AER related
registers and an AER interrupt for specified the PCIE device.
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

When a root port receives the same errors more than once before the
kernel process them, the Multiple Error Messages Received flags are set
by hardware. Because the root port could only save one kind of
correctable error source id and another uncorrectable error source id at
the same time, the second message sender id is lost if the 2 messages
are sent from 2 different devices. This patch makes the kernel search
all devices under the root port when multiple messages are received.
Reviewed-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NZhang Yanmin <yanmin_zhang@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

When the bus id part of error source id is equal to 0 or nosourceid=1,
make the kernel probe the AER status registers of all devices under the
root port to find the initial error reporter.
Reviewed-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NZhang Yanmin <yanmin_zhang@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Based on PCI Express AER specs, a root port might receive multiple
TLP errors while it could only save a correctable error source id
and an uncorrectable error source id at the same time. In addition,
some root port hardware might be unable to provide a correct source
id, i.e., the source id, or the bus id part of the source id provided
by root port might be equal to 0.

The patchset implements the support in kernel by searching the device
tree under the root port.

Patch 1 changes parameter cb of function pci_walk_bus to return a value.
When cb return non-zero, pci_walk_bus stops more searching on the
device tree.
Reviewed-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NZhang Yanmin <yanmin_zhang@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This is used by PCIE AER error injection to fake an PCI AER interrupt.
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Adds support for PCI Express transaction layer end-to-end CRC checking
(ECRC).  This patch will enable/disable ECRC checking by setting/clearing
the ECRC Check Enable and/or ECRC Generation Enable bits for devices that
support ECRC.

The ECRC setting is controlled by the "pci=ecrc=<policy>" command-line
option. If this option is not set or is set to 'bios", the enable and
generation bits are left in whatever state that firmware/BIOS set them to.
The "off" setting turns them off, and the "on" option turns them on (if the
device supports it).

Turning ECRC on or off can be a data integrity versus performance
tradeoff.  In theory, turning it on will catch more data errors, turning
it off means possibly better performance since CRC does not need to be
calculated by the PCIe hardware and packet sizes are reduced.
Signed-off-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

When an upstream port reports an AER error to root port, kernel
starts error recovery procedures. The default return value of
function pcie_portdrv_slot_reset is PCI_ERS_RESULT_NONE. If all
port service drivers of the downstream port under the upstream
port have no slot_reset method in pci_error_handlers, AER recovery
would stop without resume. Below patch against 2.6.30-rc3 fixes it.
Signed-off-by: NZhang Yanmin <yanmin.zhang@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Implement pm object for the PCI Express port driver in order to use
the new power management framework and reduce the code size.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

- Rename pci_osc_control_set() to acpi_pci_osc_control_set() according
  to the other API names in drivers/acpi/pci_root.c.

- Move _OSC related definitions to include/linux/acpi.h because _OSC
  related API is implemented in drivers/acpi/pci_root.c now.
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Reviewed-by: NAndrew Patterson <andrew.patterson@hp.com>
Tested-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The PCI Express port driver uses 'struct pcie_port_service_id' for
matching port service devices and drivers, but this structure
contains fields that duplicate information from the port device
itself (vendor, device, subvendor, subdevice) and fields that are not
used by any existing port service driver (class, class_mask,
drvier_data).  Also, both existing port service drivers (AER and
PCIe HP) don't even use the vendor and device fields for device
matching.  Therefore 'struct pcie_port_service_id' can be removed
altogether and the only useful members of it (port_type, service) can
be introduced directly into the port service device and port service
driver structures.  That simplifies the code quite a bit and reduces
its size.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The second argument of the ->probe() callback in
struct pcie_port_service_driver is unnecessary and never used.
Remove it.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Commit 47a8b0cc (Enable PCIe AER only after checking firmware
support) wants to walk the PCI bus in the remove path to disable
AER, and calls pci_walk_bus for downstream bridges.

Unfortunately, in the remove path, we remove devices and bridges
in a depth-first manner, starting with the furthest downstream
bridge and working our way backwards.

The furthest downstream bridges will not have a dev->subordinate,
and we hit a NULL deref in pci_walk_bus.

Check for dev->subordinate first before attempting to walk the
PCI hierarchy below us.
Acked-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>

The PCIe port driver currently sets the PCIe AER error reporting bits for
any root or switch port without first checking to see if firmware will grant
control. This patch moves setting these bits to the AER service driver
aer_enable_port routine.  The bits are then set for the root port and any
downstream switch ports after the check for firmware support (aer_osc_setup)
is made. The patch also unsets the bits in a similar fashion when the AER
service driver is unloaded.
Reviewed-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@hobbes.lan>