Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Trivial coding style cleanups.
Signed-off-by: NMichael Trimarchi <trimarchimichael@yahoo.it>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Under qemu there is a race between the TDxE read-and-clear and the SCxTDR
write. While on hardware it can be gauranteed that the read-and-clear
will happen prior to the character being written out, no such assumption
can be made under emulation. As this path happens with IRQs off and the
hardware itself doesn't care about the ordering, move the SCxTDR write
until after the read-and-clear.
Signed-off-by: NVladimir Prus <vladimir@codesourcery.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

SH7723 has SCIFA. This module is similer SCI register map, but it has FIFO.
So this patch adds new type(PORT_SCIFA) and change some type checking.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Correct the interrupt handler in sh4 serial device, return the correct
value and check for what is anabled in the SCSCR register. The sh7722 is
broken just sending a break using minicom.
Signed-off-by: NMichael Trimarchi <trimarchimichael@yahoo.it>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NYinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

This was added at a time when the compiler did a less than stellar job of
optimizing out dead code. These days this tends to be less of a concern,
so kill it all off.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Presently this is conditionalized on sh, and disabled for sh64.
Now that SH-5 ties in to the clock framework, the sh64 exception
can be dropped. Additionally, ARM will want to use the same hooks
once SH-Mobile G3 grows clock framework support, so switch these
paths over to HAVE_CLK now.

Once the H8 and ARM sh-sci users hook up HAVE_CLK, the driver can
be switched over to having an outright dependency on it and the
ifdefs can go away.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Presently we don't do much with UPF_IOREMAP other than special case it
for SH-5's onchip_remap() on the early console. Tie this in generically
for platforms that need the remap.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

SH7763 has 3 SCIF device. Current code supports SCIF0 and 1.
SCIF0 and 1 are same register constitution, but only SCIF2 is different.
I added support of SCIF2.
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The below is the patch to replace blindly all possible places,
including Jack's fixes.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
(Reviewed and checked rather than blindly added)
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Improve sh7722 support for SCIF1 and SCIF2 and separate code
from sh7366 implementation.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This adds basic support for the SH7723 MobileR2 CPU.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Since 43cc71ee, the platform modalias is
prefixed with "platform:".  Add MODULE_ALIAS() to the hotpluggable serial
platform drivers, to re-enable auto loading.

NOTE that Kconfig for some of these drivers doesn't allow modular builds, and
thus doesn't match the driver source's unload support.  Presumably their
unload code is buggy and/or weakly tested...

[dbrownell@users.sourceforge.net: more drivers, registration fixes]
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There was an off-by-1 in the SCRFDR calculation that caused writes over
128-bytes to hang in the FIFO. Fix it up.
Signed-off-by: NYutaro Ebihara <ebiharaml@si-linux.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This header is needed on other architectures as well (namely h8300),
which currently fails to build without this in place. Rather than
duplicating the port definition completely there, just move this to a
common location instead.

This should get h8300 working again for 2.6.25, in addition to the
changes already pushed by Sato-san in -rc2.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds sh7366 cpu supports. Just the most basic things like interrupt
controller, clocks and serial port are included at this point.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The kgdb console code requires uart_set_options() and friends, which
are only provided by the serial core when console support is enabled.
These were sitting under CONFIG_SH_KGDB and resulted in a link error
when console support wasn't enabled, work that by rolling the console
routines under CONFIG_SH_KGDB_CONSOLE, which they should have been
all along.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds support for the SH7720 (SH3-DSP) CPU.

Signed-off by: Markus Brunner <super.firetwister@gmail.com>
Signed-off by: Mark Jonas <toertel@gmail.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This was a bit more verbose than it needed to be.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch removes old dead code:
- kill off sh7300 cpu support
- get rid of broken solution engine 7300 board support
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds basic support for UP SH-X3.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds the enable/disable hooks for the port clock to sh-sci.
Signed-off-by: Ndmitry pervushin <dimka@nomadgs.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Support the SH7712 (SH3-DSP) Solution Engine reference board.
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

With the GDB stub being entered via a special sysrq trigger,
we don't want to hit it directly from sci_br_interrupt().
Without this, there is access to the other sysrq triggers when
kgdb is enabled.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds preliminary support for the SH7785-based Highlander board.
Some of the Highlander support code is reordered so that most of it
can be reused directly.

This also plugs in missing SH7785 checks in the places that need it,
as this is the first board to support the CPU.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This code has suffered quite a bit of bitrot, do some basic
tidying to get it to a reasonably functional state again.
This gets the basic support and the console working again.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The sh-sci sci_br_interrupt() handler was failing to call
in to uart_handle_break(), which was something that only
the SH-3 path was doing, fix that up.

Additionally, SUPPORT_SYSRQ seems to have moved down too
far, move it back to the top so uart_handle_break() and
friends aren't no-ops.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds CPU support for the SH7722.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This is the grungy swap all the occurrences in the right places patch that
goes with the updates.  At this point we have the same functionality as
before (except that sgttyb() returns speeds not zero) and are ready to
begin turning new stuff on providing nobody reports lots of bugs

If you are a tty driver author converting an out of tree driver the only
impact should be termios->ktermios name changes for the speed/property
setting functions from your upper layers.

If you are implementing your own TCGETS function before then your driver
was broken already and its about to get a whole lot more painful for you so
please fix it 8)

Also fill in c_ispeed/ospeed on init for most devices, although the current
code will do this for you anyway but I'd like eventually to lose that extra
paranoia

[akpm@osdl.org: bluetooth fix]
[mp3@de.ibm.com: sclp fix]
[mp3@de.ibm.com: warning fix for tty3270]
[hugh@veritas.com: fix tty_ioctl powerpc build]
[jdike@addtoit.com: uml: fix ->set_termios declaration]
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NMartin Peschke <mp3@de.ibm.com>
Acked-by: NPeter Oberparleiter <oberpar@de.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NHugh Dickins <hugh@veritas.com>
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This syncs up the SH clock framework with the linux/clk.h API,
for which there were only some minor changes required, namely
the clk_get() dev_id and subsequent callsites.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>