- 26 10月, 2011 1 次提交
-
-
由 Thomas Gleixner 提交于
IRQF_SHARED is not part of the IORESOURCE_IRQ bits. It's expressed by IORESOURCE_IRQ_SHAREABLE. IORESOURCE_IRQ_HIGHEDGE and IRQF_TRIGGER_HIGH are contradicting values, an interrupt can hardly be configured for both level and edge at the same time. This was introduced in commit 45138439(Blackfin arch: flash memory map and dm9000 resources updating) of course without any hint in the changelog what the heck this is supposed to do. Acked-by: NJavier Herrero <jherrero@hvsistemas.es> Signed-off-by: NThomas Gleixner <tglx@linutronix.de> Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
- 23 7月, 2011 2 次提交
-
-
由 Mike Frysinger 提交于
The default for the Blackfin SPI driver is 8 bits and dma disabled, so many of the bfin5xx_spi_chip resources are redundant. So punt those parts. Further, drivers should themselves be declaring 16 bit transfers, so for those that do, and for the ones which no longer do 16 bit transfers, drop the bfin5xx_spi_chip resources. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Mike Frysinger 提交于
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
- 18 3月, 2011 1 次提交
-
-
由 Mike Frysinger 提交于
The previous commit that changed this code to the common GPIO layers forgot to delete the local and now unused "i" variable. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
- 10 1月, 2011 3 次提交
-
-
由 Mike Frysinger 提交于
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Sonic Zhang 提交于
The SPORT/UART driver doesn't use the secondary channel pins, so don't try and request them thus keeping other drivers from using them. Signed-off-by: NSonic Zhang <sonic.zhang@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Mike Frysinger 提交于
We don't want people banging on MMRs directly. As for the ip0x board, it shouldn't need to muck with the CS pin directly as the Blackfin SPI bus master driver takes care of driving this. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
- 23 10月, 2010 1 次提交
-
-
由 Mike Frysinger 提交于
Now that the common 8250 serial driver supports an "irqflags" field, we don't need to patch in a custom define into the code. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
- 22 10月, 2010 4 次提交
-
-
由 steven miao 提交于
Signed-off-by: Nsteven miao <realmz6@gmail.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Mike Frysinger 提交于
Rather than use raw numbers for the GPIO pins, use proper GPIO defines. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Michael Hennerich 提交于
With the recent kernel update the isp1362-hcd driver evaluates the IORESOURCE_IRQ resource flags and requests the irq with the given polarity/edge settings. However the ISP1362 config requires low level/edge interrupts. Most of the Blackfin boards use some random flag or no flag at all. Make all boards use a know good flag IORESOURCE_IRQ_LOWEDGE. Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Barry Song 提交于
Make sure we use the right Kconfig names and platform strings. Signed-off-by: NBarry Song <barry.song@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
- 07 10月, 2010 1 次提交
-
-
由 David Howells 提交于
Split the BF532 machine type BFIN_*_FIO_FLAG() functions to their own header file to avoid circular #include problems as these functions require IRQ flag handling, which requires asm/blackfin.h, which otherwise requires the header file that defines these functions. For good measure, also get rid of the inclusion of asm/blackfin.h from mach/cdefBF532.h (which is circular) and defBF532.h (which is included by asm/blackfin.h before including this header). Signed-off-by: NDavid Howells <dhowells@redhat.com>
-
- 09 3月, 2010 5 次提交
-
-
由 Barry Song 提交于
The ASoC codec driver was generalized and renamed, so update the board resources accordingly. Signed-off-by: NBarry Song <barry.song@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Barry Song 提交于
Signed-off-by: NBarry Song <barry.song@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Sonic Zhang 提交于
This lets people easily select the UART/SPORT consoles for early printk while leveraging the pins declared in the boards file. Signed-off-by: NSonic Zhang <sonic.zhang@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Sonic Zhang 提交于
Rather than keeping the pins in the actual driver and worrying about a mess of Kconfig options, declare all the desired pin resources in the boards file. This lets people easily select the specific pins/ports for the normal emulated UART as well as GPIOs for CTS/RTS. Signed-off-by: NSonic Zhang <sonic.zhang@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Sonic Zhang 提交于
Rather than keeping the pins in the actual driver and worrying about a mess of Kconfig options, declare all the desired pin resources in the boards file. This lets people easily select the specific pins/ports for the normal UART as well as GPIOs for CTS/RTS. Signed-off-by: NSonic Zhang <sonic.zhang@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
- 15 12月, 2009 3 次提交
-
-
由 Mike Frysinger 提交于
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Mike Frysinger 提交于
No need to set MSTR in .ctl_reg as the Blackfin SPI bus driver does this already for all parts. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Michael Hennerich 提交于
Now that the driver has been updated, convert the board resources to the new i2c framework for managing slaves. For boards that don't actually hook up to this hardware, simply drop the resources altogether. Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
- 08 10月, 2009 4 次提交
-
-
由 Mike Frysinger 提交于
The simple-gpio has been replaced by the gpio sysfs interface, so drop the unused simple-gpio resources from all Blackfin boards. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Mike Frysinger 提交于
Structs get initialized to 0 already, and we want to punt this field, so scrub it from all of our boards. Reported-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Mike Frysinger 提交于
Now that the common jedec_probe supports the ST PSD4256G6V, no need to use the custom stm_flash driver. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Michael Hennerich 提交于
Now that the driver has been updated, convert the board resources to the new i2c framework for managing slaves. Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
- 07 10月, 2009 1 次提交
-
-
由 Robin Getz 提交于
Bill Gatliff & David Brownell pointed out we were missing some copyrights, and licensing terms in some of the files in ./arch/blackfin, so this fixes things, and cleans them up. It also removes: - verbose GPL text(refer to the top level ./COPYING file) - file names (you are looking at the file) - bug url (it's in the ./MAINTAINERS file) - "or later" on GPL-2, when we did not have that right It also allows some Blackfin-specific assembly files to be under a BSD like license (for people to use them outside of Linux). Signed-off-by: NRobin Getz <robin.getz@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
- 17 9月, 2009 7 次提交
-
-
由 Harald Krapfenbauer 提交于
Signed-off-by: NHarald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at> Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Barry Song 提交于
The ASoC drivers have dropped the redundant "-spi" suffix in the driver name, so update the board resources accordingly. Signed-off-by: NBarry Song <barry.song@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Mike Frysinger 提交于
These hardware devices are dead and the drivers never cleaned up/merged, so punt the useless board resource info. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Michael Hennerich 提交于
Latest smc91x driver allows you to specify settings in board resources rather than needing CONFIG_BLACKFIN in the drivers/net/smc91x.h header. Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Cliff Cai 提交于
One too many zeros means we run way faster than the codec can handle. Signed-off-by: NCliff Cai <cliff.cai@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Yi Li 提交于
Signed-off-by: NYi Li <yi.li@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Michael Hennerich 提交于
The "TWI_KEYPAD" driver was renamed to "INPUT_PCF8574", so update the defines in the board resources accordingly. Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
- 16 7月, 2009 1 次提交
-
-
由 Michael Hennerich 提交于
The sed used to rename the bfin-twi-lcd only replaced the first instance rather than all which led to the resources not being enabled when the driver was built as a module. Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
- 23 6月, 2009 1 次提交
-
-
由 Mike Frysinger 提交于
The BF533-EZKIT has two Flash In-System Programming devices hooked up to the async memory bus, so add resources for the primary flashes and the SRAMs on the devices. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
- 13 6月, 2009 1 次提交
-
-
由 Yi Li 提交于
The Blackfin SPI driver can be driven by an IRQ now, so declare it in the board resources. Signed-off-by: NYi Li <yi.li@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
- 12 6月, 2009 1 次提交
-
-
由 Mike Frysinger 提交于
Try to keep the naming conventions consistent, so: SPI_ADC_BF533 -> BFIN_SPI_ADC TWI_LCD -> BFIN_TWI_LCD Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
- 06 3月, 2009 1 次提交
-
-
由 Michael Hennerich 提交于
Signed-off-by: NMike Frysinger <vapier.adi@gmail.com> Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com> Signed-off-by: NBryan Wu <cooloney@kernel.org>
-
- 02 3月, 2009 1 次提交
-
-
由 Mike Frysinger 提交于
Signed-off-by: NMike Frysinger <vapier.adi@gmail.com> Signed-off-by: NBryan Wu <cooloney@kernel.org>
-
- 04 2月, 2009 1 次提交
-
-
由 Mike Frysinger 提交于
Drop CONFIG_I2C_BOARDINFO ifdefs as the common i2c header handles this already by stubbing things out Signed-off-by: NMike Frysinger <vapier.adi@gmail.com> Signed-off-by: NBryan Wu <cooloney@kernel.org>
-