Blackfin: drop board resources for dead devices (pbx/ad9960)

These hardware devices are dead and the drivers never cleaned up/merged,
so punt the useless board resource info.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

arch/blackfin/mach-bf518/boards/ezbrd.c

@@ -199,15 +199,6 @@ static struct bfin5xx_spi_chip mmc_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_PBX)
-static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
-	.ctl_reg	= 0x4, /* send zero */
-	.enable_dma	= 0,
-	.bits_per_word	= 8,
-	.cs_change_per_word = 1,
-};
-#endif
-
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
 	.enable_dma = 0,
@@ -296,24 +287,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.mode = SPI_MODE_3,
 	},
 #endif
-#if defined(CONFIG_PBX)
-	{
-		.modalias = "fxs-spi",
-		.max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 8 - CONFIG_J11_JUMPER,
-		.controller_data = &spi_si3xxx_chip_info,
-		.mode = SPI_MODE_3,
-	},
-	{
-		.modalias = "fxo-spi",
-		.max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 8 - CONFIG_J19_JUMPER,
-		.controller_data = &spi_si3xxx_chip_info,
-		.mode = SPI_MODE_3,
-	},
-#endif
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 	{
 		.modalias		= "ad7877",

arch/blackfin/mach-bf527/boards/cm_bf527.c

@@ -495,13 +495,6 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
-};
-#endif
-
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 	.enable_dma = 0,
@@ -509,15 +502,6 @@ static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_PBX)
-static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
-	.ctl_reg	= 0x4, /* send zero */
-	.enable_dma	= 0,
-	.bits_per_word	= 8,
-	.cs_change_per_word = 1,
-};
-#endif
-
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
 	.enable_dma = 0,
@@ -591,15 +575,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.controller_data = &ad1836_spi_chip_info,
 	},
 #endif
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-	{
-		.modalias = "ad9960-spi",
-		.max_speed_hz = 10000000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 1,
-		.controller_data = &ad9960_spi_chip_info,
-	},
-#endif
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 	{
 		.modalias = "mmc_spi",
@@ -610,24 +585,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.mode = SPI_MODE_3,
 	},
 #endif
-#if defined(CONFIG_PBX)
-	{
-		.modalias = "fxs-spi",
-		.max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 8 - CONFIG_J11_JUMPER,
-		.controller_data = &spi_si3xxx_chip_info,
-		.mode = SPI_MODE_3,
-	},
-	{
-		.modalias = "fxo-spi",
-		.max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 8 - CONFIG_J19_JUMPER,
-		.controller_data = &spi_si3xxx_chip_info,
-		.mode = SPI_MODE_3,
-	},
-#endif
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 	{
 		.modalias		= "ad7877",

arch/blackfin/mach-bf527/boards/ezbrd.c

@@ -263,15 +263,6 @@ static struct bfin5xx_spi_chip mmc_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_PBX)
-static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
-	.ctl_reg	= 0x4, /* send zero */
-	.enable_dma	= 0,
-	.bits_per_word	= 8,
-	.cs_change_per_word = 1,
-};
-#endif
-
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
 	.enable_dma = 0,
@@ -376,24 +367,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.mode = SPI_MODE_3,
 	},
 #endif
-#if defined(CONFIG_PBX)
-	{
-		.modalias = "fxs-spi",
-		.max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 8 - CONFIG_J11_JUMPER,
-		.controller_data = &spi_si3xxx_chip_info,
-		.mode = SPI_MODE_3,
-	},
-	{
-		.modalias = "fxo-spi",
-		.max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 8 - CONFIG_J19_JUMPER,
-		.controller_data = &spi_si3xxx_chip_info,
-		.mode = SPI_MODE_3,
-	},
-#endif
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 	{
 		.modalias		= "ad7877",

arch/blackfin/mach-bf527/boards/ezkit.c

@@ -512,13 +512,6 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
-};
-#endif
-
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 	.enable_dma = 0,
@@ -526,15 +519,6 @@ static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_PBX)
-static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
-	.ctl_reg	= 0x4, /* send zero */
-	.enable_dma	= 0,
-	.bits_per_word	= 8,
-	.cs_change_per_word = 1,
-};
-#endif
-
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
 	.enable_dma = 0,
@@ -632,15 +616,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.controller_data = &ad1836_spi_chip_info,
 	},
 #endif
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-	{
-		.modalias = "ad9960-spi",
-		.max_speed_hz = 10000000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 1,
-		.controller_data = &ad9960_spi_chip_info,
-	},
-#endif
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 	{
 		.modalias = "mmc_spi",
@@ -652,24 +627,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_PBX)
-	{
-		.modalias = "fxs-spi",
-		.max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 8 - CONFIG_J11_JUMPER,
-		.controller_data = &spi_si3xxx_chip_info,
-		.mode = SPI_MODE_3,
-	},
-	{
-		.modalias = "fxo-spi",
-		.max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 8 - CONFIG_J19_JUMPER,
-		.controller_data = &spi_si3xxx_chip_info,
-		.mode = SPI_MODE_3,
-	},
-#endif
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 	{
 		.modalias		= "ad7877",

arch/blackfin/mach-bf533/boards/H8606.c

@@ -201,15 +201,6 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_PBX)
-static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
-	.ctl_reg	= 0x1c04,
-	.enable_dma	= 0,
-	.bits_per_word	= 8,
-	.cs_change_per_word = 1,
-};
-#endif
-
 /* Notice: for blackfin, the speed_hz is the value of register
  * SPI_BAUD, not the real baudrate */
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
@@ -248,23 +239,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_PBX)
-	{
-		.modalias	 = "fxs-spi",
-		.max_speed_hz	 = 4,
-		.bus_num	 = 1,
-		.chip_select	 = 3,
-		.controller_data = &spi_si3xxx_chip_info,
-	},
-
-	{
-		.modalias	 = "fxo-spi",
-		.max_speed_hz	 = 4,
-		.bus_num	 = 1,
-		.chip_select	 = 2,
-		.controller_data = &spi_si3xxx_chip_info,
-	},
-#endif
 };
 
 /* SPI (0) */

arch/blackfin/mach-bf533/boards/stamp.c

@@ -219,15 +219,6 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_PBX)
-static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
-	.ctl_reg	= 0x4, /* send zero */
-	.enable_dma	= 0,
-	.bits_per_word	= 8,
-	.cs_change_per_word = 1,
-};
-#endif
-
 #if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
 static struct bfin5xx_spi_chip spidev_chip_info = {
 	.enable_dma = 0,
@@ -298,25 +289,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_PBX)
-	{
-		.modalias = "fxs-spi",
-		.max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 8 - CONFIG_J11_JUMPER,
-		.controller_data = &spi_si3xxx_chip_info,
-		.mode = SPI_MODE_3,
-	},
-	{
-		.modalias = "fxo-spi",
-		.max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 8 - CONFIG_J19_JUMPER,
-		.controller_data = &spi_si3xxx_chip_info,
-		.mode = SPI_MODE_3,
-	},
-#endif
-
 #if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
 	{
 		.modalias = "spidev",

arch/blackfin/mach-bf537/boards/cm_bf537.c

@@ -101,13 +101,6 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
-};
-#endif
-
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 	.enable_dma = 0,
@@ -150,16 +143,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-	{
-		.modalias = "ad9960-spi",
-		.max_speed_hz = 10000000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 1,
-		.controller_data = &ad9960_spi_chip_info,
-	},
-#endif
-
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 	{
 		.modalias = "mmc_spi",

arch/blackfin/mach-bf537/boards/pnav10.c

@@ -293,13 +293,6 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
-};
-#endif
-
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 static struct bfin5xx_spi_chip mmc_spi_chip_info = {
 	.enable_dma = 0,
@@ -366,15 +359,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.controller_data = &ad1836_spi_chip_info,
 	},
 #endif
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-	{
-		.modalias = "ad9960-spi",
-		.max_speed_hz = 10000000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 1,
-		.controller_data = &ad9960_spi_chip_info,
-	},
-#endif
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 	{
 		.modalias = "mmc_spi",

arch/blackfin/mach-bf537/boards/stamp.c

@@ -549,13 +549,6 @@ static struct bfin5xx_spi_chip ad1938_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
-};
-#endif
-
 #if defined(CONFIG_INPUT_EVAL_AD7147EBZ)
 #include <linux/input.h>
 #include <linux/input/ad714x.h>
@@ -698,15 +691,6 @@ static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_PBX)
-static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
-	.ctl_reg	= 0x4, /* send zero */
-	.enable_dma	= 0,
-	.bits_per_word	= 8,
-	.cs_change_per_word = 1,
-};
-#endif
-
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 #include <linux/spi/ad7877.h>
 static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
@@ -906,16 +890,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-	{
-		.modalias = "ad9960-spi",
-		.max_speed_hz = 10000000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 1,
-		.controller_data = &ad9960_spi_chip_info,
-	},
-#endif
-
 #if defined(CONFIG_INPUT_EVAL_AD7147EBZ)
 	{
 		.modalias = "ad714x_captouch",
@@ -940,24 +914,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.mode = SPI_MODE_3,
 	},
 #endif
-#if defined(CONFIG_PBX)
-	{
-		.modalias = "fxs-spi",
-		.max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 8 - CONFIG_J11_JUMPER,
-		.controller_data = &spi_si3xxx_chip_info,
-		.mode = SPI_MODE_3,
-	},
-	{
-		.modalias = "fxo-spi",
-		.max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 8 - CONFIG_J19_JUMPER,
-		.controller_data = &spi_si3xxx_chip_info,
-		.mode = SPI_MODE_3,
-	},
-#endif
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 	{
 		.modalias		= "ad7877",

arch/blackfin/mach-bf537/boards/tcm_bf537.c

@@ -101,13 +101,6 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
-};
-#endif
-
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 static struct bfin5xx_spi_chip mmc_spi_chip_info = {
 	.enable_dma = 0,
@@ -150,16 +143,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-	{
-		.modalias = "ad9960-spi",
-		.max_speed_hz = 10000000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 1,
-		.controller_data = &ad9960_spi_chip_info,
-	},
-#endif
-
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 	{
 		.modalias = "mmc_spi",

arch/blackfin/mach-bf561/boards/cm_bf561.c

@@ -98,13 +98,6 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
-};
-#endif
-
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 static struct bfin5xx_spi_chip mmc_spi_chip_info = {
 	.enable_dma = 0,
@@ -146,15 +139,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.controller_data = &ad1836_spi_chip_info,
 	},
 #endif
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-	{
-		.modalias = "ad9960-spi",
-		.max_speed_hz = 10000000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 1,
-		.controller_data = &ad9960_spi_chip_info,
-	},
-#endif
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 	{
 		.modalias = "mmc_spi",