We now compute the watermarks correctly, so just return an error if we
can't support the configuration.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-15-ville.syrjala@linux.intel.com

On VLV/CHV enabling sprite0 when sprite1 has already been enabled may
lead to an underrun. This only happens when sprite0 FIFO size is zero
prior to enabling it. Hence an effective workaround is to always
allocate at least one cacheline for sprite0 when sprite1 is active.

I've not observed this sort of failure during any other type of plane
enable/disable sequence.

v2: s/noninverted/raw/ for consistency with other platforms

Testcase: igt/kms_plane_blinker
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-14-ville.syrjala@linux.intel.com

Clear out the watermark for all disabled planes to 0. This is required
to avoid falsely thinking that the inherited watermarks are bogus in
case the watermark is actually higher than the FIFO size.

v2: s/noninverted/raw/ for consistency with other platforms
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-13-ville.syrjala@linux.intel.com

Remove crtc->wm.cxsr_allowed and just rely on crtc_state->disable_cxsr
instead. This was used only by vlv/chv to indicate whether to enable
cxsr in the wm computation. That doesn't really work anymore, and as far
as the optimal watermarks go we'll just consider the number of planes
and the current pipe, and for the intermediate watermarks we'll also
start to consider disable_cxsr which is set appropriately when planes
are being enabled/disabled.

We'll also flip over the crtc_state->wm.need_postvbl_update setup so
that it's the wm code that will set it. Previously the generic code set
it up, and then the wm code cleared it again if it thought it's not
needed after all.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-11-ville.syrjala@linux.intel.com

Since the watermark registers arent double buffered on VLV/CHV, we'll
need to play around with intermediate watermarks same was as we do on
ILK-BDW.

The watermark registers on VLV/CHV contain inverted values, so to find
the intermediate watermark value we just take the minimum of the
active and optimal values. This also means that, unlike ILK-BDW,
there's no chance that we'd fail to find a working intermediate
watermarks. As long as both the active and optimal watermarks are valid
the intermediate watermarks will come out valid as well.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-10-ville.syrjala@linux.intel.com

Check whether anything relevant has actually change when we compute new
watermarks for each plane in the state. If the watermarks for no
primary/sprite planes changed we don't have to recompute the FIFO split
or reprogram the DSBARB registers. And even the cursor watermarks didn't
change we can skip the merge+invert step between all the planes on
the pipe as well.

v2: s/noninverted/raw/ for consistency with other platforms
v3: Drop duplicated vlv_get_fifo_size() call during init
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-9-ville.syrjala@linux.intel.com

Start computing the vlv/chv watermarks the atomic way, from the
.compute_pipe_wm() hook. We'll recompute the actual watermarks
for only planes that are part of the state, the other planes will
keep their watermark from the last time it was computed.

And the actual watermark programming will happen from the
.initial_watermarks() hook. For now we'll just compute the
optimal watermarks, and we'll hook up the intermediate
watermarks properly later.

The DSPARB registers responsible for the FIFO paritioning are
double buffered, so they will be programming from
intel_begin_crtc_commit().

v2: s/noninverted/raw/ for consistency with other platforms
    s/vlv_plane_wm_set/vlv_raw_plane_wm_set/ for clarity
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-8-ville.syrjala@linux.intel.com

Let's compute the watermarks first and the FIFO size second. This way we
can make sure the FIFO split is the most accommodating to the watermarks.
Previously we could have potentially computed a FIFO split that couldn't
accommodate the PM2 watermarks simply due to a bad split even if the
total FIFO size would have been sufficient.

It'll also allow us to avoid recomputing the wms for all planes whenever
the FIFO split would change. Thus we don't have to add any extra planes
to the state when the FIFO needs to be repartitioned.

To help with this we'll keep around copies of the non-inverted
watermarks in the crtc state. For now that doesn't help too much, but
once we start to do the watermark computation only for the planes
that change we'll need the non-inverted values around for the other
planes.

v2: s/noninverted/raw/ for consistency with other platforms
    Fix the memset() of the "raw" watermarks
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-7-ville.syrjala@linux.intel.com

Move the vlv/chv FIFO size tracking into the crtc_state. As with the wms
for now this just acts as temporary storage.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-6-ville.syrjala@linux.intel.com

Relocate the vlv/chv wm state to live under intel_crtc_state. Note
that for now this just behaves as a temporary storage. But it'll be
easier to conver the thing over to properly pre-computing the state
when it's already in the right place.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-5-ville.syrjala@linux.intel.com

In an effort to make the vlv/chv wm code look and behave more like the
ilk+ code, let's move the current active wms next to the
corresponding ilk wms.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-4-ville.syrjala@linux.intel.com

Track the plane fifo sizes under intel_crtc instead of under each
intel_plane. Avoids looping over the planes in a bunch of places,
and later we'll move this tracking into the crtc state properly.

v2: Nuke intel_plane_wm_parameters (Maarten)
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-3-ville.syrjala@linux.intel.com

assert_spin_locked() becomes an unconditionally compiled BUG_ON(),
adding debug code right into the heart of critical routines like
interrupt handlers.

   text	   data	    bss	    dec	    hex
1296480	  19944	   2272	1318696	 141f28	before (lockdep disabled)
1295984	  19944	   2272	1318200	 141d38	after

1336261	  21139	   3208	1360608	 14c2e0	before (lockdep enabled)
1339920	  21139	   3208	1364267	 14d12b	after

Small saving for release; hopefully more instructive in debug.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302132801.599-1-chris@chris-wilson.co.ukReviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

In order to make cursor updates actually safe wrt. watermark programming
we have to clear the legacy_cursor_update flag in the atomic state. That
will cause the regular atomic update path to do the necessary vblank
wait after the plane update if needed, otherwise the vblank wait would
be skipped and we'd feed the optimal watermarks to the hardware before
the plane update has actually happened.

To make the slow vs. fast path determination in
intel_legacy_cursor_update() a little simpler we can ignore the actual
visibility of the plane (which can only get computed once we've already
chosen out path) and instead we simply check whether the fb is being
set or cleared by the user. This means a fully clipped but logically
visible cursor will be considered visible as far as watermark
programming is concerned. We can do that for the cursor since it's a
fixed size plane and the clipped size doesn't play a role in the
watermark computation.

This should fix underruns that can occur when the cursor gets
enable/disabled or the size gets changed. Hopefully it's good enough
that only pure cursor movement and flips go through unthrottled.

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Reported-by: NUwe Kleine-König <uwe@kleine-koenig.org>
Fixes: f79f2692 ("drm/i915: Add a cursor hack to allow converting legacy page flip to atomic, v3.")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170217150159.11683-1-ville.syrjala@linux.intel.comReviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Tested-by: NRafael Ristovski <rafael.ristovski@gmail.com>

After
commit 2c7d0602
Author: Imre Deak <imre.deak@intel.com>
Date:   Mon Dec 5 18:27:37 2016 +0200

    drm/i915/gen9: Fix PCODE polling during CDCLK change notification

there is still one report of the CDCLK-change request timing out on a
KBL machine, see the Reference link. On that machine the maximum time
the request took to succeed was 34ms, so increase the timeout to 50ms.

v2:
- Change timeout from 100 to 50 ms to maintain the current 50 ms limit
  for atomic waits in the driver. (Chris, Tvrtko)

Reference: https://bugs.freedesktop.org/show_bug.cgi?id=99345
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1487946730-17162-1-git-send-email-imre.deak@intel.com

Certain Baytrails, namely the 4 cpu core variants, have been
plaqued by spurious system hangs, mostly occurring with light loads.

Multiple bisects by various people point to a commit which changes the
reclocking strategy for Baytrail to follow its bigger brethen:
commit 8fb55197 ("drm/i915: Agressive downclocking on Baytrail")

There is also a review comment attached to this commit from Deepak S
on avoiding punit access on Cherryview and thus it was excluded on
common reclocking path. By taking the same approach and omitting
the punit access by not tweaking the thresholds when the hardware
has been asked to move into different frequency, considerable gains
in stability have been observed.

With J1900 box, light render/video load would end up in system hang
in usually less than 12 hours. With this patch applied, the cumulative
uptime has now been 34 days without issues. To provoke system hang,
light loads on both render and bsd engines in parallel have been used:
glxgears >/dev/null 2>/dev/null &
mpv --vo=vaapi --hwdec=vaapi --loop=inf vid.mp4

So far, author has not witnessed system hang with above load
and this patch applied. Reports from the tenacious people at
kernel bugzilla are also promising.

Considering that the punit access frequency with this patch is
considerably less, there is a possibility that this will push
the, still unknown, root cause past the triggering point on most loads.

But as we now can reliably reproduce the hang independently,
we can reduce the pain that users are having and use a
static thresholds until a root cause is found.

v3: don't break debugfs and simplification (Chris Wilson)

References: https://bugzilla.kernel.org/show_bug.cgi?id=109051
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: fritsch@xbmc.org
Cc: miku@iki.fi
Cc: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
CC: Michal Feix <michal@feix.cz>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Deepak S <deepak.s@linux.intel.com>
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.2+
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487166779-26945-1-git-send-email-mika.kuoppala@intel.com

Implement WaDDIIOTimeout to avoid a timeout when enabling the DDI IO
power domains.
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170222063431.10060-5-ander.conselvan.de.oliveira@intel.com

The uncached mmio is sufficient to queue the mmio writes without raising
forcewake. The forced flush along with acquiring forcewake from the
posting read is not required for adjusting the RPS frequency.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170220094713.22874-3-chris@chris-wilson.co.ukReviewed-by: NRadoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>

If intel_set_rps() is called whilst the hw is disabled, just store the
requested frequency (from the user) for application when we wake the hw
up.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170220094713.22874-2-chris@chris-wilson.co.ukReviewed-by: NRadoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>

Instead of having each back-end provide identical guards, just have a
singular set in intel_set_rps() to verify that the caller is obeying the
rules.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NRadoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170220094713.22874-1-chris@chris-wilson.co.uk

No need to cater for old A revisions.
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487172099-24873-2-git-send-email-jani.nikula@intel.com

Currently we apply the jump to rpe if we are below it and the GPU needs
more power. For some GPUs, the rpe is 75% of the maximum range causing
us to dramatically overshoot low power applications *and* unable to
reach the low frequency that can most efficiently deliver their
workload.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170210150348.22146-3-chris@chris-wilson.co.ukReviewed-by: NRadoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>

When the RPS tuning was applied to Baytrail, in commit 8fb55197
("drm/i915: Agressive downclocking on Baytrail"), concern was given that
it might cause Cherryview excess wakeups of the common power well.
However, the static thresholds perform poorly for Kodi, and the GPU is
unable to deliver the video frames on time. Enabling the dynamic, finer
thresholds used on all other platforms (including Skylake and Broxton
that also have the same multiple powerwell concerns) allows the GPU to
pick a more appropriate frequency and not drop frames.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170210150348.22146-1-chris@chris-wilson.co.ukReviewed-by: NRadoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>

With latest Punit FW, vgg input voltag drop falling to minimum is fixed.
So reverting the WA patch & moving to turbo freq opreation range to [RPn -> RP0]

This is not a 1:1 revert of the commit 5b7c91b7.
You can refer to commit 5b5929cb ("drm/i915/chv: remove
pre-production hardware workarounds") as the reason for the discrepancy

commit 5b7c91b7
Author: Deepak S <deepak.s@linux.intel.com>
Date:   Sat May 9 18:15:46 2015 +0530

    drm/i915/chv: Set min freq to efficient frequency on chv

v2: Fix inconsistent return type. (Chris)
v3: drop pre-production hw case (Ville)
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDeepak S <deepak.s@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471007801-86075-1-git-send-email-deepak.s@linux.intel.comReviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

This workaround for BDW was incomplete as it also requires EUTC clock
gating to be disabled via UCGCTL1.

v2: read modify write UCGTL1 in broadwell_init_clock_gating (Ville)
Signed-off-by: NRobert Bragg <robert@sixbynine.org>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170212133252.20990-1-robert@sixbynine.orgReviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

Move ilk_pipe_pixel_rate() next to its only caller
(intel_crtc_compute_pixel_rate()).
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170120182205.8141-15-ville.syrjala@linux.intel.com

The current dev_cdclk vs. cdclk vs. atomic_cdclk_freq is quite a mess.
So here I'm introducing the "actual" and "logical" naming for our
cdclk state. "actual" is what we'll bash into the hardware and "logical"
is what everyone should use for state computaion/checking and whatnot.
We'll track both using the intel_cdclk_state as both will need other
differing parameters than just the actual cdclk frequency.

While doing that we can at the same time unify the appearance of the
.modeset_calc_cdclk() implementations a little bit.

v2: Commit dev_priv->cdclk.actual since that already has the
    new state by the time .modeset_commit_cdclk() is called.
v3: s/locical/logical/ and improve the docs a bit
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170120182205.8141-9-ville.syrjala@linux.intel.com

Rather than recomputing the pipe pixel rate on demand everywhere, let's
just stick the precomputed value into the crtc state.

v2: Rebase due to min_pixclk[] code movement
    Document the new pixel_rate struct member (Ander)
    Combine vlv/chv with bdw+ in intel_modeset_readout_hw_state()
v3: Fix typos in commit message (David)

Cc: Ander Conselvan De Oliveira <conselvan2@gmail.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170126195031.32343-1-ville.syrjala@linux.intel.com

Apply workarounds to Geminilake, and annotate those that are applied
unconditionally when they apply to GLK based on the workaround database.

v2: Fix commit message typos. (David)
v3: Rebase.
Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NDavid Weinehall <david.weinehall@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485422218-9102-1-git-send-email-ander.conselvan.de.oliveira@intel.com

The write to the punit may fail, so propagate the error code back to its
callers. Of particular interest are the RPS writes, so add appropriate
user error codes and logging.

v2: Add DEBUG for failed frequency changes during RPS.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170126101919.13211-1-chris@chris-wilson.co.ukReviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>

Remove WaGsvDisableTurbo and WaRsUseTimeoutMode as these were only for
pre-production Broxton devices, and this code is now defunct.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

Along with GLK it was introduced the .is_lp and IS_GEN9_LP.
So, following the same simplification standard we can
put Skylake and Kabylake under the same bucket for most
of the things.

So let's add the IS_GEN9_BC for "Big Core" (non Atom based
platforms).

The i915_drv.c was let out of this patch on purpose
because that is really a decision per platform, just like
other cases where IS_KABYLAKE is different from IS_SKYLAKE.

v2: fix conflict with IS_LP and 3 new cases for this
    big core bucket:
    - intel_ddi.c: intel_ddi_get_link_dpll
    - intel_fbc.c: find_compression_threshold
    - i915_gem_gtt.c: gtt_write_workarounds

Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <conselvan2@gmail.com>
Acked-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485196357-30599-2-git-send-email-rodrigo.vivi@intel.com

Ville explained that the wakelock was being acquired during set-idle in
order to flush the voltage change from the punit.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170102152845.32352-1-chris@chris-wilson.co.ukReviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

BSpec says:
"Overlay Clock Gating Must be Disabled: Overlay & L2 Cache clock gating
must be disabled in order to prevent device hangs when turning off overlay.SW
must turn off Ovrunit clock gating (6200h) and L2 Cache clock gating (C8h)."

We only turned off the overlay clock gating (due to lack of docs I
presume). After a bit of experimentation it looks like the the magic
C8h register lives in the PCI config space of device 0, and the magic
bit appears to be bit 2. Or at the very least this eliminates the GPU
death after MI_OVERLAY_OFF.

L2 clock gating seems to save ~80mW, so let's keep it on unless we need
to actually use the overlay.

Also let's move the OVRUNIT clock gating to the same place since we can,
and 845 supposedly doesn't need it.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1481131693-27993-11-git-send-email-ville.syrjala@linux.intel.comAcked-by: NChris Wilson <chris@chris-wilson.co.uk>

According to the previous patch, it's possible atm that we call
intel_do_sagv_disable() only once during the 1ms period and time out if
that call fails. As opposed to this the spec says that we need to keep
retrying this request for a 1ms duration, so let's do this similarly to
the CDCLK change notification request.

v4-5:
- Rebased on the reply_mask, reply change.
v6:
- Remove w/s change. (Lyude)
- Rebased on the timeout_base argument change.

Cc: Lyude <cpaul@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Fixes: 656d1b89 ("drm/i915/skl: Add support for the SAGV, fix underrun hangs")
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: Lyude <lyude@redhat.com> (v4)
Link: http://patchwork.freedesktop.org/patch/msgid/1480955258-26311-2-git-send-email-imre.deak@intel.com
(cherry picked from commit b3b8e999)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

commit 848496e5
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date:   Wed Jul 13 16:32:03 2016 +0300

    drm/i915: Wait up to 3ms for the pcu to ack the cdclk change request on SKL

increased the timeout to match the spec, but we still see a timeout on
at least one SKL. A CDCLK change request following the failed one will
succeed nevertheless.

I could reproduce this problem easily by running kms_pipe_crc_basic in a
loop. In all failure cases _wait_for() was pre-empted for >3ms and so in
the worst case - when the pre-emption happened right after calculating
timeout__ in _wait_for() - we called skl_cdclk_wait_for_pcu_ready() only
once which failed and so _wait_for() timed out. As opposed to this the
spec says to keep retrying the request for at most a 3ms period.

To fix this send the first request explicitly to guarantee that there is
3ms between the first and last request. Though this matches the spec, I
noticed that in rare cases this can still time out if we sent only a few
requests (in the worst case 2) _and_ PCODE is busy for some reason even
after a previous request and a 3ms delay. To work around this retry the
polling with pre-emption disabled to maximize the number of requests.
Also increase the timeout to 10ms to account for interrupts that could
reduce the number of requests. With this change I couldn't trigger
the problem.

v2:
- Use 1ms poll period instead of 10us. (Chris)
v3:
- Poll with pre-emption disabled to increase the number of request
  attempts. (Ville, Chris)
- Factor out a helper to poll, it's also needed by the next patch.
v4:
- Pass reply_mask, reply to skl_pcode_request(), instead of assuming the
  reply is generic. (Ville)
v5:
- List the request specific timeout values as code comment. (Ville)
v6:
- Try the poll first with preemption enabled.
- Add code comment about first request being queued by PCODE. (Art)
- Add timeout_base_ms argument. (Ville)
v7:
- Clarify code comment about first queued request. (Chris)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Art Runyan <arthur.j.runyan@intel.com>
Cc: <stable@vger.kernel.org> # v4.2- : 3b2c1710 : drm/i915: Wait up to 3ms
Cc: <stable@vger.kernel.org> # v4.2-
Fixes: 5d96d8af ("drm/i915/skl: Deinit/init the display at suspend/resume")
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=97929
Testcase: igt/kms_pipe_crc_basic/suspend-read-crc-pipe-B
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1480955258-26311-1-git-send-email-imre.deak@intel.com
(cherry picked from commit a0b8a1fe)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

The requests conversion introduced a nasty bug where we could generate a
new request in the middle of constructing a request if we needed to idle
the system in order to evict space for a context. The request to idle
would be executed (and waited upon) before the current one, creating a
minor havoc in the seqno accounting, as we will consider the current
request to already be completed (prior to deferred seqno assignment) but
ring->last_retired_head would have been updated and still could allow
us to overwrite the current request before execution.

We also employed two different mechanisms to track the active context
until it was switched out. The legacy method allowed for waiting upon an
active context (it could forcibly evict any vma, including context's),
but the execlists method took a step backwards by pinning the vma for
the entire active lifespan of the context (the only way to evict was to
idle the entire GPU, not individual contexts). However, to circumvent
the tricky issue of locking (i.e. we cannot take struct_mutex at the
time of i915_gem_request_submit(), where we would want to move the
previous context onto the active tracker and unpin it), we take the
execlists approach and keep the contexts pinned until retirement.
The benefit of the execlists approach, more important for execlists than
legacy, was the reduction in work in pinning the context for each
request - as the context was kept pinned until idle, it could short
circuit the pinning for all active contexts.

We introduce new engine vfuncs to pin and unpin the context
respectively. The context is pinned at the start of the request, and
only unpinned when the following request is retired (this ensures that
the context is idle and coherent in main memory before we unpin it). We
move the engine->last_context tracking into the retirement itself
(rather than during request submission) in order to allow the submission
to be reordered or unwound without undue difficultly.

And finally an ulterior motive for unifying context handling was to
prepare for mock requests.

v2: Rename to last_retired_context, split out legacy_context tracking
for MI_SET_CONTEXT.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161218153724.8439-3-chris@chris-wilson.co.uk

Replace uses of fb->pixel_format with fb->format->format.
Less duplicated information is a good thing.

Note that coccinelle failed to eliminate the
"/* fourcc format */" comment from drm_framebuffer.h, so I had
to do that part manually.

@@
struct drm_framebuffer *FB;
expression E;
@@
 drm_helper_mode_fill_fb_struct(...) {
	...
-	FB->pixel_format = E;
	...
 }

@@
struct drm_framebuffer *FB;
expression E;
@@
 i9xx_get_initial_plane_config(...) {
	...
-	FB->pixel_format = E;
	...
 }

@@
struct drm_framebuffer *FB;
expression E;
@@
 ironlake_get_initial_plane_config(...) {
	...
-	FB->pixel_format = E;
	...
 }

@@
struct drm_framebuffer *FB;
expression E;
@@
 skylake_get_initial_plane_config(...) {
	...
-	FB->pixel_format = E;
	...
 }

@@
struct drm_framebuffer *a;
struct drm_framebuffer b;
@@
(
- a->pixel_format
+ a->format->format
|
- b.pixel_format
+ b.format->format
)

@@
struct drm_plane_state *a;
struct drm_plane_state b;
@@
(
- a->fb->pixel_format
+ a->fb->format->format
|
- b.fb->pixel_format
+ b.fb->format->format
)

@@
struct drm_crtc *CRTC;
@@
(
- CRTC->primary->fb->pixel_format
+ CRTC->primary->fb->format->format
|
- CRTC->primary->state->fb->pixel_format
+ CRTC->primary->state->fb->format->format
)

@@
struct drm_mode_set *set;
@@
(
- set->fb->pixel_format
+ set->fb->format->format
|
- set->crtc->primary->fb->pixel_format
+ set->crtc->primary->fb->format->format
)

@@
@@
 struct drm_framebuffer {
	 ...
-	 uint32_t pixel_format;
	 ...
 };

v2: Fix commit message (Laurent)
    Rebase due to earlier removal of many fb->pixel_format uses,
    including the 'fb->format = drm_format_info(fb->format->format);'
    snafu
v3: Adjusted the semantic patch a bit and regenerated due to code
    changes

Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> (v1)
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1481751175-18463-1-git-send-email-ville.syrjala@linux.intel.com

Replace drm_format_plane_cpp(fb->pixel_format) with just
fb->format->cpp[]. Avoids the expensive format info lookup.

@@
struct drm_framebuffer *a;
struct drm_framebuffer b;
expression E;
@@
(
- drm_format_plane_cpp(a->pixel_format, E)
+ a->format->cpp[E]
|
- drm_format_plane_cpp(b.pixel_format, E)
+ b.format->cpp[E]
)

@@
struct drm_plane_state *a;
struct drm_plane_state b;
expression E;
@@
(
- drm_format_plane_cpp(a->fb->pixel_format, E)
+ a->fb->format->cpp[E]
|
- drm_format_plane_cpp(b.fb->pixel_format, E)
+ b.fb->format->cpp[E]
)

@@
struct drm_framebuffer *a;
identifier T;
expression E;
@@
  T = a->pixel_format
<+...
- drm_format_plane_cpp(T, E)
+ a->format->cpp[E]
...+>

@@
struct drm_framebuffer b;
identifier T;
expression E;
@@
  T = b.pixel_format
<+...
- drm_format_plane_cpp(T, E)
+ b.format->cpp[E]
...+>

v2: Rerun spatch due to code changes

Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Suggested-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1481751057-18123-1-git-send-email-ville.syrjala@linux.intel.com

Don't access plane_state->fb until we know the plane to be visible.
It it's visible, it will have an fb, and thus we don't have to
consider the NULL fb case. Makes the code look nicer.

Cc: intel-gfx@lists.freedesktop.org
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479498793-31021-25-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>