So far the modeset code enabled all power domains if it needed any. It
wasn't a problem since HW generations so far only had one always-on
power well and one dynamic power well that can be enabled/disabled. For
domains powered by always-on power wells (panel fitter on pipe A and the
eDP transcoder) we didn't do anything, for all other domains we just
enabled the single dynamic power well.

Future HW generations will change this, as they add multiple dynamic
power wells. Support for these will be added later, this patch prepares
for those by making sure we only enable the required domains.

Note that after this change on HSW we'll enable all power domains even
if it was the domain for the panel fitter on pipe A or the eDP
transcoder. This isn't a problem since the power domain framework
already checks if the domain is on an always-on power well and doesn't
do anything in this case.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Fill out the HSW watermark s/w tracking structures with the current
hardware state in intel_modeset_setup_hw_state(). This allows us to skip
the HW state readback during watermark programming and just use the values
we keep around in dev_priv->wm. Reduces the overhead of the watermark
programming quite a bit.

v2: s/init_wm/wm_get_hw_state
    Remove stale comment about sprites
    Make DDB partitioning readout safer
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Fix whitespace fail.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Introduce a new struct intel_pipe_wm which contains all the
watermarks for a single pipe. Use it to unify the LP0 and LP1+
watermark computations so that we can just iterate through the
watermark levels neatly and call ilk_compute_wm_level() for each.

Also add another tool ilk_wm_merge() that merges the LP1+ watermarks
from all pipes. For that, embed one intel_pipe_wm inside intel_crtc that
contains the currently valid watermarks for each pipe.

This is mainly preparatory work for pre-computing the watermarks for
each pipe and merging them at a later time. For now the merging still
happens immediately.

v2: Add some comments about level 0 DDB split and intel_wm_config
    Add WARN_ON for level 0 being disabled
    s/lp_wm/merged
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This file is all about the legacy fbdev support. If we want to extract
framebuffer functions, we better put those into a separate file.

Also rename functions accordingly, only two have used the intel_fb_
prefix anyway.
Reviewed-by: NChon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Boots Just Fine (tm)!

The only glitch seems to be that at least on Fedora the boot splash
gets confused and doesn't display much at all.

And since there's no ugly console flickering anymore in between, the
flicker while switching between X servers (VT support is still enabled)
is even more jarring.

Also, I'm unsure whether we don't need to somehow kick out vgacon, now
that nothing else gets in the way. But stuff seems to work, so I
don't care. Also everything still works as well with VGA_CONSOLE=n

Also the #ifdef mess needs a bit of a cleanup, follow-up patches will
do just that.

To keep the Kconfig tidy, extract all the i915 options into its own
file.

v2:
- Rebase on top of the preliminary hw support option and the
  intel_drv.h cleanup.
- Shut up warnings in i915_debugfs.c

v3: Use the right CONFIG variable, spotted by Chon Ming.

Cc: Lee, Chon Ming <chon.ming.lee@intel.com>
Cc: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NChon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Let's try to avoid these confusing negated booleans.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Something already got misplaced (although it's from a patch from
before Paulo's cleanup). Move it to the right spot.

v2: Remove the line to keep a neat block, requested by Paulo.
Reported-by: NPaulo Zanoni <przanoni@gmail.com>
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: NPaulo Zanoni <przanoni@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The intel_flush_primary_plane name actually tells us which plane
we're talking about.

Also reorganize the internals a bit and add a missing POSTING_READ()
to make sure the hardware has seen the changes by the time we
return from the function.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

IPS should be OK as long as one plane is enabled on the pipe, but
it does seem to cause problems when going between primary only and
sprite only.

This needs more investigations, but for now just disable IPS whenever
the primary plane is disabled.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It's not really needed, rather just adds another place to hold
intermediate values that could go wrong, and it's not clear that the
training pattern set or training lane set should be written at this
point at all.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

If we encounter a situation where the CPU blocks waiting for results
from the GPU, give the GPU a kick to boost its the frequency.

This should work to reduce user interface stalls and to quickly promote
mesa to high frequencies - but the cost is that our requested frequency
stalls high (as we do not idle for long enough before rc6 to start
reducing frequencies, nor are we aggressive at down clocking an
underused GPU). However, this should be mitigated by rc6 itself powering
off the GPU when idle, and that energy use is dependent upon the workload
of the GPU in addition to its frequency (e.g. the math or sampler
functions only consume power when used). Still, this is likely to
adversely affect light workloads.

In particular, this nearly eliminates the highly noticeable wake-up lag
in animations from idle. For example, expose or workspace transitions.
(However, given the situation where we fail to downclock, our requested
frequency is almost always the maximum, except for Baytrail where we
manually downclock upon idling. This often masks the latency of
upclocking after being idle, so animations are typically smooth - at the
cost of increased power consumption.)

Stéphane raised the concern that this will punish good applications and
reward bad applications - but due to the nature of how mesa performs its
client throttling, I believe all mesa applications will be roughly
equally affected. To address this concern, and to prevent applications
like compositors from permanently boosting the RPS state, we ratelimit the
frequency of the wait-boosts each client recieves.

Unfortunately, this techinique is ineffective with Ironlake - which also
has dynamic render power states and suffers just as dramatically. For
Ironlake, the thermal/power headroom is shared with the CPU through
Intelligent Power Sharing and the intel-ips module. This leaves us with
no GPU boost frequencies available when coming out of idle, and due to
hardware limitations we cannot change the arbitration between the CPU and
GPU quickly enough to be effective.

v2: Limit each client to receiving a single boost for each active period.
    Tested by QA to only marginally increase power, and to demonstrably
    increase throughput in games. No latency measurements yet.

v3: Cater for front-buffer rendering with manual throttling.

v4: Tidy up.

v5: Sadly the compositor needs frequent boosts as it may never idle, but
due to its picking mechanism (using ReadPixels) may require frequent
waits. Those waits, along with the waits for the vrefresh swap, conspire
to keep the GPU at low frequencies despite the interactive latency. To
overcome this we ditch the one-boost-per-active-period and just ratelimit
the number of wait-boosts each client can receive.
Reported-and-tested-by: NPaul Neumann <paul104x@yahoo.de>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=68716Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Kenneth Graunke <kenneth@whitecape.org>
Cc: Stéphane Marchesin <stephane.marchesin@gmail.com>
Cc: Owen Taylor <otaylor@redhat.com>
Cc: "Meng, Mengmeng" <mengmeng.meng@intel.com>
Cc: "Zhuang, Lena" <lena.zhuang@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[danvet: No extern for function prototypes in headers.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

struct drm_mode_display now has a separate crtc_ version of the clock to
be used when we're talking about the timings given to the harwadre (was
far as the mode is concerned).

This commit is really the result of a git grep adjusted_mode.*clock and
replacing those by adjusted_mode.crtc_clock. No functional change.

v2: Rebased on drm-intel-queued-next
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Acked-by: NDave Airlie <airlied@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Since I already reorganized the header file, Daniel requested me to
remove those keywords. It seems "checkpath.pl --strict" also doesn't
like "extern" on header files.

At least now we're consistent :)
Requested-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

These functions were added before the final PC8 implementation, and
their callers moved to intel_display.c during the code review.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

By moving them to intel_fb.c.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

And move it so it doesn't need a forward declaration.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Also move it to the top of the file so we can remove the forward
declaration.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Daniel complained that we keep adding stuff to the bottom of the file,
so we constantly have conflicts. So reorganize everything and split
them file-by-file, also sorting the files in alphabetical order. This
way, patches touching different files will have a smaller chance of
conflicting. Of course, this commit will conflict with everybody on
the list :)

Also remove a few useless comments and make some things fit into 80
lines.

v2: - Conflict with intel_ddi_get_config
Requested-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Call intel_ddi_get_config() to get the pipe_bpp settings from
DDI.

The sync polarity settings from DDI are irrelevant for CRT
output, so override them with data from the ADPA register.

v2: Extract intel_crt_get_flags()

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=69691Tested-by: NQingshuai Tian <qingshuai.tian@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

And the gratious overallocation of crtcs. Seems to go back to the ums
days of yonder ...

We also still need it to make the fbdev emulation happy, but I don't
think there's really a need. Especially since the current fbdev
emulation doesn't actually support cloning.

v2: Use sizeof(*pointer) pattern (Jani).

Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add APIs to get/put power well references for specific purposes.

v2: Split the i915_request change to another patch
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Reorganize the internal i915_request power well handling to use the
reference count just like everyone else. This way all we need to do is
check the reference count and we know whether the power well needs to be
enabled of disabled.

v2: Split he intel_display_power_{get,put} change to another patch.
    Add intel_resume_power_well() to make sure we enable the power
    well on resume
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Determine the need for double wide mode already in compute_config
stage as we need that information to figure out if horizontal
coordinates need to be adjusted.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Try to clarify the purpose of requested_mode.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Rather that mess about with hdisplay/vdisplay from requested_mode, add
explicit pipe src size information to pipe config.

Now requested_mode is only really relevant for dvo/sdvo output timings.
For everything else either adjusted_mode or pipe src size should be
used.

In many places where we end up using pipe source size, we should
actually use the primary plane size, but we don't currently store
that information explicitly. As long as we treat primaries as full
screen only, we can get away with this. Eventually when we move
primaries over to drm_plane, we need to fix it all up.

v2: Add a comment to explain what pipe_src_{w,h} are
    Add a note about primary planes to commit message
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Move intel_crtc_active() to intel_display.c and make it available
elsewhere as well.

intel_edp_psr_match_conditions() already has one open coded copy,
so replace that one with a call to intel_crtc_active().

v2: Copy paste a big comment from danvet's mail explaining
    when we can ditch the extra checks
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Now that adjusted_mode.clock no longer contains the pixel_multiplier, we
can kill the get_clock() callback and instead do the clock readout
in get_pipe_config().

Also i9xx_crtc_clock_get() can now extract the frequency of the PCH
DPLL, so use it to populate port_clock accurately for PCH encoders.
For DP in port A the encoder is still responsible for filling in
port_clock. The FDI adjusted_mode.clock extraction is kept in place
for some extra sanity checking, but we no longer need to pretend it's
also the port_clock.

In the encoder get_config() functions fill out adjusted_mode.clock
based on port_clock and other details such as the DP M/N values,
HDMI 12bpc and SDVO pixel_multiplier. For PCH encoders we will then
do an extra sanity check to make sure the dotclock we derived from
the FDI configuratiuon matches the one we derive from port_clock.

DVO doesn't exist on PCH platforms, so it doesn't need to anything
but assign adjusted_mode.clock=port_clock. And DDI is HSW only, so
none of the changes apply there.

v2: Use hdmi_reg color format to detect 12bpc HDMI case
v3: Set adjusted_mode.clock for LVDS too
v4: Rename ironlake_crtc_clock_get to ironlake_pch_clock_get,
    eliminate the useless link_freq variable.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Extract the code to calculate the dotclock from the link clock and M/N
values into a new function from ironlake_crtc_clock_get().

The new function can be used to calculate the dotclock for both FDI and
DP cases.

Also simplify the code a bit along the way.

v2: Don't forget about non-pch encoders in ironlake_crtc_clock_get()
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add functions to read out the CPU and PCH transcoder M/N values,
and use them to fill out the pipe config dp_m_n information. And
while at it populate has_dp_encoder too.

Also refactor ironlake_get_fdi_m_n_config() to simply call the new
intel_cpu_transcoder_get_m_n() function.

v2: Remember the DDI
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It would be easier if adjusted_mode.clock would be the pipe pixel clock,
and it actually is, except for the cases where pixel_multiplier > 1.

So let's change intel_sdvo to use port_clock as the multiplied clock,
and then we can leave adjusted_mode.clock as pipe pixel clock.

v2: Improve port_clock documentation
    Rebased on top of SDVO pixel_multiplier fixes
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Passing the appropriate crtc to intel_update_watermarks() should help
in avoiding needless work in the future.

v2: Avoid clash with internal 'crtc' variable in some wm functions
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Detangle the additional state of whether or not the hw has the pfit
enabled from whether it has zero size. This allows us to cleanly
distinguish in the code when we expect the pfit to be enabled (for
Haswell pc8), and when the BIOS is confused and needs sanitizing.
Reported-by: Nshui yanwei <yangweix.shui@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=68251Tested-by: Nshui yanwei <yangweix.shui@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When transitioning away from vgacon the system tries to save the
current contents of the VGA memory, so that it can be cleanly handed
off to fbcon (or whatever comes afterwards).

The recent change

 commit 81b5c7bc
 Author: Alex Williamson <alex.williamson@redhat.com>
 Date:   Wed Aug 28 09:39:08 2013 -0600

    i915: Update VGA arbiter support for newer devices

caused i915 to disable VGA memory decode for the IGD when i915 is
initializing. Unfortunately that happens before the vgacon->fbcon
handoff so vgacon_save_screen() will read out all ones from the
VGA memory.

After the handoff fbcon will inherit the bogus state from vgacon,
and pre-fills the fb with matching contents. The end result is
a white rectangle in the top left corner of the screen, the size
of which matches the now inactive VGA console.

To remedy the situation delay the disabling of VGA memory until
the vgacon->fbcon handoff has happened.

Also rename i915_enable_vga to i915_enable_vga_mem to make
the relationship between these functions clearer.

Cc: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In preparation for followup work.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This does not include any panel specific sub-encoders yet.

v2: Fix fixed mode handling (Daniel)

v3: Mostly based on Ville's review comments.
 - Fix MIPI_HS_TX_TIMEOUT.
 - DPI_ENABLE only for video mode.
 - Drop ULPS usage for now, use DEVICE_READY only.
 - Set MIPI_INIT_COUNT based on txclkesc.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

intel_fixed_panel_mode() overwrote the adjusted_mode with the fixed mode
only partially. Notably it forgot to copy over the sync flags. The LVDS code however programmed the hardware with the sync flags from fixed mode, and then later the pipe config comparison obviously failed as we
filled out the adjusted_mode in get_config from the real registers.

Just call drm_mode_copy() in intel_fixed_panel_mode() to copy over the
whole thing, and then just use adjusted_mode in the LVDS code to figure
out which sync settings the hardware needs.

Also constify the fixed_mode argument to intel_fixed_panel_mode().
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch allows PC8+ states on Haswell. These states can only be
reached when all the display outputs are disabled, and they allow some
more power savings.

The fact that the graphics device is allowing PC8+ doesn't mean that
the machine will actually enter PC8+: all the other devices also need
to allow PC8+.

For now this option is disabled by default. You need i915.allow_pc8=1
if you want it.

This patch adds a big comment inside i915_drv.h explaining how it
works and how it tracks things. Read it.

v2: (this is not really v2, many previous versions were already sent,
     but they had different names)
    - Use the new functions to enable/disable GTIMR and GEN6_PMIMR
    - Rename almost all variables and functions to names suggested by
      Chris
    - More WARNs on the IRQ handling code
    - Also disable PC8 when there's GPU work to do (thanks to Ben for
      the help on this), so apps can run caster
    - Enable PC8 on a delayed work function that is delayed for 5
      seconds. This makes sure we only enable PC8+ if we're really
      idle
    - Make sure we're not in PC8+ when suspending
v3: - WARN if IRQs are disabled on __wait_seqno
    - Replace some DRM_ERRORs with WARNs
    - Fix calls to restore GT and PM interrupts
    - Use intel_mark_busy instead of intel_ring_advance to disable PC8
v4: - Use the force_wake, Luke!
v5: - Remove the "IIR is not zero" WARNs
    - Move the force_wake chunk to its own patch
    - Only restore what's missing from RC6, not everything
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Just like we're doing with the other IMR changes.

One of the functional changes is that not every caller was doing the
POSTING_READ.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>