drm/i915: Add HSW CRT output readout support

Call intel_ddi_get_config() to get the pipe_bpp settings from
DDI.

The sync polarity settings from DDI are irrelevant for CRT
output, so override them with data from the ADPA register.

v2: Extract intel_crt_get_flags()

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=69691Tested-by: NQingshuai Tian <qingshuai.tian@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

drivers/gpu/drm/i915/intel_crt.c

@@ -83,13 +83,11 @@ static bool intel_crt_get_hw_state(struct intel_encoder *encoder,
 	return true;
 }
 
-static void intel_crt_get_config(struct intel_encoder *encoder,
-				 struct intel_crtc_config *pipe_config)
+static unsigned int intel_crt_get_flags(struct intel_encoder *encoder)
 {
 	struct drm_i915_private *dev_priv = encoder->base.dev->dev_private;
 	struct intel_crt *crt = intel_encoder_to_crt(encoder);
 	u32 tmp, flags = 0;
-	int dotclock;
 
 	tmp = I915_READ(crt->adpa_reg);
 
@@ -103,16 +101,37 @@ static void intel_crt_get_config(struct intel_encoder *encoder,
 	else
 		flags |= DRM_MODE_FLAG_NVSYNC;
 
-	pipe_config->adjusted_mode.flags |= flags;
+	return flags;
+}
+
+static void intel_crt_get_config(struct intel_encoder *encoder,
+				 struct intel_crtc_config *pipe_config)
+{
+	struct drm_device *dev = encoder->base.dev;
+	int dotclock;
+
+	pipe_config->adjusted_mode.flags |= intel_crt_get_flags(encoder);
 
 	dotclock = pipe_config->port_clock;
 
-	if (HAS_PCH_SPLIT(dev_priv->dev))
+	if (HAS_PCH_SPLIT(dev))
 		ironlake_check_encoder_dotclock(pipe_config, dotclock);
 
 	pipe_config->adjusted_mode.clock = dotclock;
 }
 
+static void hsw_crt_get_config(struct intel_encoder *encoder,
+			       struct intel_crtc_config *pipe_config)
+{
+	intel_ddi_get_config(encoder, pipe_config);
+
+	pipe_config->adjusted_mode.flags &= ~(DRM_MODE_FLAG_PHSYNC |
+					      DRM_MODE_FLAG_NHSYNC |
+					      DRM_MODE_FLAG_PVSYNC |
+					      DRM_MODE_FLAG_NVSYNC);
+	pipe_config->adjusted_mode.flags |= intel_crt_get_flags(encoder);
+}
+
 /* Note: The caller is required to filter out dpms modes not supported by the
  * platform. */
 static void intel_crt_set_dpms(struct intel_encoder *encoder, int mode)
@@ -804,7 +823,10 @@ void intel_crt_init(struct drm_device *dev)
 	crt->base.mode_set = intel_crt_mode_set;
 	crt->base.disable = intel_disable_crt;
 	crt->base.enable = intel_enable_crt;
-	crt->base.get_config = intel_crt_get_config;
+	if (IS_HASWELL(dev))
+		crt->base.get_config = hsw_crt_get_config;
+	else
+		crt->base.get_config = intel_crt_get_config;
 	if (I915_HAS_HOTPLUG(dev))
 		crt->base.hpd_pin = HPD_CRT;
 	if (HAS_DDI(dev))

drivers/gpu/drm/i915/intel_ddi.c

@@ -1269,8 +1269,8 @@ static void intel_ddi_hot_plug(struct intel_encoder *intel_encoder)
 		intel_dp_check_link_status(intel_dp);
 }
 
-static void intel_ddi_get_config(struct intel_encoder *encoder,
-				 struct intel_crtc_config *pipe_config)
+void intel_ddi_get_config(struct intel_encoder *encoder,
+			  struct intel_crtc_config *pipe_config)
 {
 	struct drm_i915_private *dev_priv = encoder->base.dev->dev_private;
 	struct intel_crtc *intel_crtc = to_intel_crtc(encoder->base.crtc);

drivers/gpu/drm/i915/intel_drv.h

@@ -828,5 +828,7 @@ extern void ironlake_check_encoder_dotclock(const struct intel_crtc_config *pipe
 
 extern bool intel_crtc_active(struct drm_crtc *crtc);
 extern void i915_disable_vga_mem(struct drm_device *dev);
+extern void intel_ddi_get_config(struct intel_encoder *encoder,
+				 struct intel_crtc_config *pipe_config);
 
 #endif /* __INTEL_DRV_H__ */