Gadget must be informed about disconnection when pullup is
removed.
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

After all endpoints are disabled, fifo_map should have reached 0.
Its a bug if if didn't, so warn about it and reset it to 0 so that
driver can continue using all the fifos.
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When selecting different alt setting, s3c_hsotg_ep_enable can be
called with fifo already allocated. Allocate fifo again only if
required and after deallocating the previous fifo.
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Current algorithm picks the first fifo which is equal to or greater
than the required size. This can result in bigger fifos assigned to
endpoints with smaller maxps. Change the algorithm to pick the
smallest fifo which is greater than or equal to the required size.

Moreover, only use signed variables when required.
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This flag is set before sending the zlp. So use present tense instead
of the past tense.
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Enable phy driver to report vbus session. This allows us to remove
D+ pullup when vbus is not present.
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Can't stay in the loop forever. Break it after timeout.
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The warning is probably good but it has false positives in both dma and non-dma
cases. So its not very helpful in either.
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

According to programming guide, zero length packet should be
programmed on its own and should not be counted in DIEPTSIZ.PktCnt
with other packets.

For ep0, this is the zlp for DATA IN stage (if required) and not for
the STATUS stage.
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Manage ep0 state in software to add handling of status OUT stage.
Just toggling hsotg->setup in s3c_hsotg_handle_outdone leaves it in
wrong state in 2-stage control transfers.
Moreover, ensure that for setup-packet s3c_hsotg_handle_outdone is
called either from SetupDone or OutDone but not both. Dwc2 ip v3.00a
generates both SetupDone and OutDone on setup packets.
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

kill_all_requests() can flush the fifo. Call it after disabling the
endpoint.
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When matching tx fifo to endpoint, consider all fifos instead of
hard limiting to 8
Moreover, print error in case no fifo could be found.
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

< 15 check doesn't show debug information for endpoint 15.
It is possible to have less than 15 endpoints so use limit
provided by hardware configuration.
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

These members are only occupying space.
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

As fifo size can vary between SOCs, add possibility to configure
them from device tree. Fifo sizes used by the legacy driver will
be used If they are not provided by the device tree.
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Reviewed-by: NRobert Baldyga <r.baldyga@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Current code does not check endpoint 15 interrupt. Use number
of endpoint configured in hardware instead of the hardcoded value.
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

GHWCFG1 provides hardware configuration of each endpoint. Use
it to configure the endpoints instead of assuming all even
endpoint are OUT and all odd endpoints are IN.
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Indicate if gadget driver must use dma for usb transfers.
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

* Add an of specific function to parse device node properties.
* Enable dma usage only if device tree property 'g_use_dma' is present.
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Do a read-modify-write instead of only setting DMAEn bit.
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

HBstLen is GAHBCFG[4:1]. Use GAHBCFG_HBSTLEN_SHIFT to write burst-
length at correct position.
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

In the error path, s3c_hsotg_phy_disable should be called after a
call to s3c_hsotg_phy_enable is made.
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When using DMA, data of the previous setup packet can be read back
from cache because ep0 and ctrl buffers are embedded in struct s3c_hsotg.
Allocate buffers instead of embedding them.
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Reviewed-by: NRobert Baldyga <r.baldyga@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Only process DOEPINT.XferCompl on data packet as DOEPINTn.SetUp can
occur with or without DOEPINT.XferCompl. When DOEPINT.SetUp occurs
with DOEPINT.XferCompl, only DOEPINT.SetUp needs to be handled.

Moreover, ignore DOEPINT.XferCompl when it occurs with
DOEPINT.StupPktRcvd as driver needs to wait for DOEPINT.SetUp to
continue.
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When using DMA, keep fifo empty interrupt disabled. Otherwise
core is flooded by interrupts.
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Bind peripheral controller to the phy on udc_start. Unbind on
udc_stop.
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

UDC core has already done it after .udc_start.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

UDC core has already done it before .udc_stop and after .udc_start.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

UDC core has already done it before .udc_stop and after .udc_start.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Instead of using variable length array, use a static length equal to
the size of the ffs->ev.types array.  This gets rid of a sparse warning:

	drivers/usb/gadget/function/f_fs.c:401:44: warning:
	Variable length array is used.

and makes it more explicit that the array has a very tight upper size
limit.  Also add some more documentation about the ev.types array and
how its size is limited and affects the rest of the code.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Reported-by: NRohith Seelaboyina <rseelaboyina@nvidia.com>
Signed-off-by: NMichal Nazarewicz <mina86@mina86.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

It's needed, to have more than 64 bytes of maxpacketsize.
Signed-off-by: NRobert Baldyga <r.baldyga@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add support for vbus detection and power supply. This code is more or
less stolen from phy-gpio-vbus-usb.c, and aims at providing a detection
mechanism for VBus (ie. usb cable plug) based on a GPIO line, and a
power supply activation which draws current from the VBus.

[ balbi@ti.com : fix build break ]
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Enhance the phy documentation by adding 2 new optional bindings :
 - the vbus gpio, which detects usb insertion
 - the vbus regulator, which provides current drawn from the usb cable
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Change internal gpio handling from integer gpios into gpio
descriptors. This change only addresses the internal API and
device-tree/ACPI, while the legacy platform data remains integer space
based.

This change is only build compile tested, and very prone to error. I
leave this comment for now in the commit message so that this patch gets
some testing as I'm pretty sure it's buggy.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Cache INT_ENB register value in order to avoid uncached iomem access, and
thus improve access time to INT_ENB value.
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Avoid interpreting useless status flags when we're not waiting for such
events by masking the status variable with the interrupt enabled register
value.
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Reported-by: NPatrice VILCHEZ <patrice.vilchez@atmel.com>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

at91sam9g45 and at91sam9x5 SoCs have an hardware bug forcing us to
generate a pulse on the BIAS signal on "USB end of reset” and
“USB end of resume" events.
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Reported-by: NPatrice VILCHEZ <patrice.vilchez@atmel.com>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

at91sam9rl SoC has an erratum forcing us to toggle the BIAS on USB
suspend/resume events.

This specific handling is only activated when CONFIG_ARCH_AT91SAM9RL is
set and this option is only set when building a non-DT kernel, which is
problematic since non-DT support for at91sam9rl SoC has been removed.

Rework the toggle_bias implementation to attach it to the "at91sam9rl-udc"
compatible string.

Add new compatible strings to avoid executing at91sam9rl erratum handling
on other SoCs.
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Removes some functions that are not used anywhere:
fsl_otg_tick_timer() view_ulpi()

This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: NRickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: NFelipe Balbi <balbi@ti.com>