Disable coalesce water mark mode of CQ for Lancer
Signed-off-by: NPadmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixed bug to make sure 'pvid' retrieval will work on big endian hosts.
Fixed incorrect comparison between the Rx Completion's 16-bit VLAN TCI
and the PVID. Now comparing only the relevant 12 bits corresponding to
the VID.
Renamed 'vid' field under Rx Completion to 'vlan_tag' to reflect
accurate description.
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Same WRB entry was being reused over different iterations of a
loop while issuing non-embedded IOCTL requests.Fixed couple of minor bugs
in this path as well.
Re-factored code to alloc/free memory for DMA outside of loop
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

eth_get_statistics and vlan_config command have same opcode.
Use opcode subsystem id to differentiate one from other.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>

Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

So far be2net has been using BE3 in legacy mode. It now checks for native
 mode capability and if available it sets it. In native mode, the RX_COMPL
 structure is different from that in legacy mode.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change f/w command versions for Lancer
Signed-off-by: NPadmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NSubramanian Seetharaman <subbu.seetharaman@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use hba_port_num for phy loopback and ethtool phy identification.

From: Suresh R <suresh.reddy@emulex.com>
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to display temperature of ASIC via ethtool -S

From: Somnath K <somnath.kotur@emulex.com>
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With transparent VLAN tagging, the ASIC wrongly indicates packets with VLAN ID.
Strip them off in the driver. The VLAN Tag to be stripped will be given to the host
as an async message.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

change occurances of stats_ioctl_sent to stats_cmd_sent
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Avoid accessing the hardware when UE is detected.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

be_cmd_pmac_add/del functions need to pass domain number to the firmware.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Found by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the mbox polling uses the schedule_timeout, the mbox_lock should be
a mutex and not a spin lock.
The commit f25b03a7 replaced udelay() with schedule_timeout() but didn't
change mbox_lock to semaphore or mutex.
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Regarding  benet be_cmd_multicast_set() function, now using
netdev_for_each_mc_addr() helper for mac address copy, but
when copying to req->mac[] did not increase of the index.

Cc: Sathya Perla <sathyap@serverengines.com>
Cc: Subbu Seetharaman <subbus@serverengines.com>
Cc: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Cc: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: NJoe Jin <joe.jin@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Lancer can use the same pattern as BE to indicate a driver load
to the FW.
Signed-off-by: NPadmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Key changes are:
- EQ ids are not assigned consecutively in Lancer. So, fix mapping of MSIx
  vector to EQ-id.
- BAR mapping and some req locations different for Lancer.
- TCP,UDP,IP checksum fields must be compulsorily set in TX wrb for TSO in
  Lancer.
- CEV_IST reg not present in Lancer; so, peek into event queue to check for
  new entries
- cq_create and mcc_create cmd interface is different for Lancer; handle
  accordingly
Signed-off-by: NPadmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The following code and data are defined but never used in current
driver.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changes to use one of the priority codes allowed by CNA f/w for NIC traffic
from host. The driver gets the bit map of the priority codes allowed for
host traffic through a asynchronous message from the f/w that the driver
subscribes to.
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds multiple RX queue support to be2net. There are
upto 4 extra rx-queues per port into which TCP/UDP traffic can be hashed into.
Some of the ethtool stats are now displayed on a per queue basis.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change "return (EXPR);" to "return EXPR;"

return is not a function, parentheses are not required.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Async notifications other than link status are possible in certain
configurations. Remove the BUG_ON in the mcc completion processing path.
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ONLINE registers can return 0xFFFFFFFF on more than one
occassion. On systems that care, reading these registers could
lead to problems.

So the new code decides that the ASIC has encountered and error
by reading the UE_STATUS_LOW/HIGH registers. AND them with
the mask values and a non-zero result indicates an error.
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

GET_STATS request uses the same memory region as the response.
If a new request for get stats is fired before the response for
the previous get_stats request is received, the response will
corrupt the new request, causing the f/w to misbehave.
Signed-off-by: NSomnath K <somnathk@serverengines.com>
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

when the BE device becomes unresponsive, dump the registers to help debugging
Signed-off-by: NSomnath K <somnathk@serverengines.com>
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes names of some variables.
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a virtual function driver in initialized, the network mac
query command can fail. Skip display of error message in that case.
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

be2net driver is currently not showing correct phy details in certain cases.
This patch fixes it.
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ibm p7 architecure seems to reorder memory accesses more
aggressively than previous ppc64 architectures. This requires memory
barriers to ensure that rx/tx doorbells are pressed only after
memory to be DMAed is written.
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current code fails on ppc as hdr.timeout is not being converted
to le32.
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As mbox polling is done only in process context, it is better to
use schedule_timeout() instead of udelay().
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes some sparse warnings:
drivers/net/benet/be_cmds.c:1503:12: warning: function
	'be_cmd_enable_magic_wol' with external linkage has definition
drivers/net/benet/be_cmds.c:1668:12: warning: function
	'be_cmd_get_seeprom_data' with external linkage has definition
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NSarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>