Disable coalesce water mark mode of CQ for Lancer
Signed-off-by: NPadmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In Lancer if a frame is DMAed partially due to lack of RX buffers,
an error completion is sent with packet size as zero and num_recvd
indicating number of used buffers. These buffers need to be freed
and packet dropped.
Signed-off-by: NPadmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TTY layer expects 0 if the ldisc->open operation succeeded.
Reported-by: NMatvejchikov Ilya <matvejchikov@gmail.com>
Signed-off-by: NOliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Like other mobile broadband device ethernet interfaces, mark the LG
VL600 with the 'wwan' devtype so userspace knows it needs additional
configuration via the AT port before the interface can be used.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the current logging styles.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert logging messages to more current styles.

Added -DDEBUG to Makefile to maintain current message logging.
This could be converted to a specific CONFIG_TULIP_DEBUG option.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the current more descriptive logging styles.

Add pr_fmt and remove PFX where appropriate.
Use netif_<level>, netdev_<level>
Indent a few blocks in xircom_cb where appropriate.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change the blocks that are guarded by #if DEBUG to
be #if defined DEBUG && DEBUG > 1 so that pr_debug
can be used later.

Remove enter/leave macros and uses.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support new device OKI SEMICONDUCTOR ML7223 IOH(Input/Output Hub).
The ML7223 IOH is for MP(Media Phone) use.
The ML7223 is companion chip for Intel Atom E6xx series.
The ML7223 is completely compatible for Intel EG20T PCH.
Signed-off-by: NTomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mac_pton() parses MAC address in form XX:XX:XX:XX:XX:XX and only in that form.

mac_pton() doesn't dirty result until it's sure string representation is valid.

mac_pton() doesn't care about characters _after_ last octet,
it's up to caller to deal with it.

mac_pton() diverges from 0/-E return value convention.
Target usage:

	if (!mac_pton(str, whatever->mac))
		return -EINVAL;
	/* ->mac being u8 [ETH_ALEN] is filled at this point. */
	/* optionally check str[3 * ETH_ALEN - 1] for termination */

Use mac_pton() in pktgen and netconsole for start.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull read_lock(&bond->lock) and BOND_IS_OK() to bond_start_xmit() from
mode-dependent xmit functions.

netif_running() is always true in hard_start_xmit.
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Unknown 8168 chips did not have any PLL power method set as they
did not inherit a default family soon enough. Fix it.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>

- RTL_GIGA_MAC_NONE is a fake index so put it at the end of the
  enumeration and shift everybody.
- RTL_GIGA_MAC_VER_17 / RTL_GIGA_MAC_VER_16 ordering fixed. Though
  not wrong it was confusing enough to wonder if things were right.

Renaming rtl_chip_info was not strictly necessary. It allows to
check the patch for the correct use of the indexes though.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>

There is no real firmware version yet but the manpage of ethtool
is rather terse about the driver information.

Former output:
$ ethtool -i eth1
driver: r8169
version: 2.3LK-NAPI
firmware-version:
bus-info: 0000:01:00.0
$ ethtool -i eth0
driver: r8169
version: 2.3LK-NAPI
firmware-version:
bus-info: 0000:03:00.0

Current output:
$ ethtool -i eth1
driver: r8169
version: 2.3LK-NAPI
firmware-version: N/A
bus-info: 0000:01:00.0

$ ethtool -i eth0
driver: r8169
version: 2.3LK-NAPI
firmware-version: rtl_nic/rtl8168d-1.fw
bus-info: 0000:03:00.0
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Fixed-by Ciprian Docan <docan@eden.rutgers.edu>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Cc: Fejes József <fejes@joco.name>
Cc: Borislav Petkov <borislav.petkov@amd.com>

Invocation of rtl8169_rx_interrupt from rtl8169_reset_task was originally
intended to retrieve as much packets as possible from the rx ring when a
reset was needed. Nowadays rtl8169_reset_task is only scheduled, with
some delay
a. from the tx timeout watchdog
b. when resuming
c. from rtl8169_rx_interrupt itself

It's dubious that the loss of outdated packets will matter much for a)
and b). c) does not need to call itself again.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>

The implementation was a bit krusty.

The 10s rtl8169_phy_timer timer has been (was ?) required with older
8169 for adequate phy operation when full gigabit is advertised in
autonegotiated mode. The timer does nothing if the link is up.
Otherwise it keeps resetting the phy until things improve.

- the device private data field phy_1000_ctrl_reg was used to
  schedule the timer. Avoid it and save a few bytes.

- rtl8169_set_settings
  pending timer is disabled before changing the link settings as
  rtl8169_phy_timer is not always needed (see the removed test in
  rtl8169_phy_timer).

- rtl8169_set_speed
  the requested link parameters may not match the chipset : bail out
  early on failure.

- rtl8169_open
  Calling rtl8169_request_timer is redundant with
  -> rtl8169_open
     -> rtl8169_init_phy
        -> rtl8169_set_speed
           -> mod_timer
  The latter always enables the phy timer whereas the former did not
  for RTL_GIGA_MAC_VER_01. It should not make things worse but only
  time will tell if reality agrees.

- rtl8169_request_timer : unused yet. Removed.

- rtl8169_delete_timer : useless. Bloat. Removed.

Side effect : the timer may kick in if the TBI is enabled. I do not
know if the TBI has ever been used in real life.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>

Shorten chipset version test.

No functional change.

Careful readers will notice that the 'supports_gmii' flag is deduced
from the device PCI id. Though less specific than the chipset related
RTL_GIGA_MAC_VER_XY, it is good enough to detect a GMII deprieved 810x.
Some features push for a device specific configuration (improved jumbo
frame support for instance). 'supports_gmii' will follow this path
if / when the device PCI id test stops working.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>

The checksum judgment was mistaken.
  Judgment result
     0:Correct 1:Wrong

This patch fixes the issue.
Signed-off-by: NToshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The collision detection setting was invalid.
When collision occurred, because data was not resent,
there was an issue to which a transmitting throughput falls.

This patch enables the collision detection.
Signed-off-by: NToshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TTY layer expects 0 if the ldisc->open operation succeeded.

Signed-off-by : Matvejchikov Ilya <matvejchikov@gmail.com>
Acked-by: NOliver Hartkopp <socketcan@hartkopp.net>
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixed bug to make sure 'pvid' retrieval will work on big endian hosts.
Fixed incorrect comparison between the Rx Completion's 16-bit VLAN TCI
and the PVID. Now comparing only the relevant 12 bits corresponding to
the VID.
Renamed 'vid' field under Rx Completion to 'vlan_tag' to reflect
accurate description.
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently EHEA reports to ethtool as supporting 10M, 100M, 1G and
10G and connected to FIBRE independent of the hardware configuration.
However, when connected to FIBRE the only supported speed is 10G
full-duplex, and the other speeds and modes are only supported
when connected to twisted pair.
Signed-off-by: NKleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Acked-by: NBreno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

veth devices dont use the batched device unregisters yet.

Since veth are a pair of devices, it makes sense to use a batch of two
unregisters, this roughly divides dismantle time by two.

Fix this by changing dellink() callers to always provide a non NULL
head. (Idea from Michał Mirosław)

This patch also handles macvlan case : We now dismantle all macvlans on
top of a lower dev at once.
Reported-by: NAlex Bligh <alex@alex.org.uk>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Michał Mirosław <mirqus@gmail.com>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enables ethtool to set the loopback mode on a given interface.
By configuring the interface in loopback mode in conjunction with a policy
route / rule, a userland application can stress the egress / ingress path
exposing the flows of the change in progress and potentially help developer(s)
understand the impact of those changes without even sending a packet out
on the network.

Following set of commands illustrates one such example -
    a) ip -4 addr add 192.168.1.1/24 dev eth1
    b) ip -4 rule add from all iif eth1 lookup 250
    c) ip -4 route add local 0/0 dev lo proto kernel scope host table 250
    d) arp -Ds 192.168.1.100 eth1
    e) arp -Ds 192.168.1.200 eth1
    f) sysctl -w net.ipv4.ip_nonlocal_bind=1
    g) sysctl -w net.ipv4.conf.all.accept_local=1
    # Assuming that the machine has 8 cores
    h) taskset 000f netserver -L 192.168.1.200
    i) taskset 00f0 netperf -t TCP_CRR -L 192.168.1.100 -H 192.168.1.200 -l 30
Signed-off-by: NMahesh Bandewar <maheshb@google.com>
Acked-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The USB protocol this driver implements appears to require 2 bytes of
padding in front of each received packet.  This used to be equal to
the value of NET_IP_ALIGN on x86, so the driver abused that constant
and mostly worked, but this is no longer the case.  The driver also
mixed up the URB and packet lengths, resulting in 2 bytes of junk at
the end of the skb.

Introduce a private constant for the 2 bytes of padding; fix this
confusion and check for the under-length case.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I deleted it by mistake in the TX_CHECKSUM removal
commit.
Reported-by: NMichał Mirosław <mirqus@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

OS2BMC registers are available for X540.
This patch adds ethtool counters based on those registers.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NEvan Swanson <evan.swanson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

feed RSS hash into skb->rxhash
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NEvan Swanson <evan.swanson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Based on patch from Stephen Hemminger.
Convert igb driver to use new set_phys_id ethtool interface.

CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Based on the original patch from Stephen Hemminger.
Convert to new LED control infrastucture and remove no longer
necessary bits.

CC: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Based on the original patch from Stephen Hemminger.
Implement set_phys_id to control LED.

CC: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Using the vmxnet3 driver produces a lockdep warning because
vmxnet3_set_mc(), which is called with mc->mca_lock held, takes
adapter->cmd_lock.  However, there are a couple of places where
adapter->cmd_lock is taken with softirqs enabled, lockdep warns that a
softirq that tries to take mc->mca_lock could happen while
adapter->cmd_lock is held, leading to an AB-BA deadlock.

I'm not sure if this is a real potential deadlock or not, but the
simplest and best fix seems to be simply to make sure we take cmd_lock
with spin_lock_irqsave() everywhere -- the places with plain spin_lock
just look like oversights.

The full enormous lockdep warning is:

 =========================================================
 [ INFO: possible irq lock inversion dependency detected ]
 2.6.39-rc6+ #1
 ---------------------------------------------------------
 ifconfig/567 just changed the state of lock:
  (&(&mc->mca_lock)->rlock){+.-...}, at: [<ffffffff81531e9f>] mld_ifc_timer_expire+0xff/0x280
 but this lock took another, SOFTIRQ-unsafe lock in the past:
  (&(&adapter->cmd_lock)->rlock){+.+...}

 and interrupts could create inverse lock ordering between them.

 other info that might help us debug this:
 4 locks held by ifconfig/567:
  #0:  (rtnl_mutex){+.+.+.}, at: [<ffffffff8147d547>] rtnl_lock+0x17/0x20
  #1:  ((inetaddr_chain).rwsem){.+.+.+}, at: [<ffffffff810896cf>] __blocking_notifier_call_chain+0x5f/0xb0
  #2:  (&idev->mc_ifc_timer){+.-...}, at: [<ffffffff8106f21b>] run_timer_softirq+0xeb/0x3f0
  #3:  (&ndev->lock){++.-..}, at: [<ffffffff81531dd2>] mld_ifc_timer_expire+0x32/0x280

 the shortest dependencies between 2nd lock and 1st lock:
   -> (&(&adapter->cmd_lock)->rlock){+.+...} ops: 11 {
      HARDIRQ-ON-W at:
                                            [<ffffffff8109ad86>] __lock_acquire+0x7f6/0x1e10
                                            [<ffffffff8109ca4d>] lock_acquire+0x9d/0x130
                                            [<ffffffff81571156>] _raw_spin_lock+0x36/0x70
                                            [<ffffffffa000d212>] vmxnet3_alloc_intr_resources+0x22/0x230 [vmxnet3]
                                            [<ffffffffa0014031>] vmxnet3_probe_device+0x5f6/0x15c5 [vmxnet3]
                                            [<ffffffff812df67f>] local_pci_probe+0x5f/0xd0
                                            [<ffffffff812dfde9>] pci_device_probe+0x119/0x120
                                            [<ffffffff81373df6>] driver_probe_device+0x96/0x1c0
                                            [<ffffffff81373fcb>] __driver_attach+0xab/0xb0
                                            [<ffffffff81372a1e>] bus_for_each_dev+0x5e/0x90
                                            [<ffffffff81373a2e>] driver_attach+0x1e/0x20
                                            [<ffffffff813735b8>] bus_add_driver+0xc8/0x290
                                            [<ffffffff813745b6>] driver_register+0x76/0x140
                                            [<ffffffff812e0046>] __pci_register_driver+0x66/0xe0
                                            [<ffffffffa001b03a>] serio_raw_poll+0x3a/0x60 [serio_raw]
                                            [<ffffffff81002165>] do_one_initcall+0x45/0x190
                                            [<ffffffff810aa76b>] sys_init_module+0xfb/0x250
                                            [<ffffffff8157a142>] system_call_fastpath+0x16/0x1b
      SOFTIRQ-ON-W at:
                                            [<ffffffff8109adb7>] __lock_acquire+0x827/0x1e10
                                            [<ffffffff8109ca4d>] lock_acquire+0x9d/0x130
                                            [<ffffffff81571156>] _raw_spin_lock+0x36/0x70
                                            [<ffffffffa000d212>] vmxnet3_alloc_intr_resources+0x22/0x230 [vmxnet3]
                                            [<ffffffffa0014031>] vmxnet3_probe_device+0x5f6/0x15c5 [vmxnet3]
                                            [<ffffffff812df67f>] local_pci_probe+0x5f/0xd0
                                            [<ffffffff812dfde9>] pci_device_probe+0x119/0x120
                                            [<ffffffff81373df6>] driver_probe_device+0x96/0x1c0
                                            [<ffffffff81373fcb>] __driver_attach+0xab/0xb0
                                            [<ffffffff81372a1e>] bus_for_each_dev+0x5e/0x90
                                            [<ffffffff81373a2e>] driver_attach+0x1e/0x20
                                            [<ffffffff813735b8>] bus_add_driver+0xc8/0x290
                                            [<ffffffff813745b6>] driver_register+0x76/0x140
                                            [<ffffffff812e0046>] __pci_register_driver+0x66/0xe0
                                            [<ffffffffa001b03a>] serio_raw_poll+0x3a/0x60 [serio_raw]
                                            [<ffffffff81002165>] do_one_initcall+0x45/0x190
                                            [<ffffffff810aa76b>] sys_init_module+0xfb/0x250
                                            [<ffffffff8157a142>] system_call_fastpath+0x16/0x1b
      INITIAL USE at:
                                           [<ffffffff8109a9e9>] __lock_acquire+0x459/0x1e10
                                           [<ffffffff8109ca4d>] lock_acquire+0x9d/0x130
                                           [<ffffffff81571156>] _raw_spin_lock+0x36/0x70
                                           [<ffffffffa000d212>] vmxnet3_alloc_intr_resources+0x22/0x230 [vmxnet3]
                                           [<ffffffffa0014031>] vmxnet3_probe_device+0x5f6/0x15c5 [vmxnet3]
                                           [<ffffffff812df67f>] local_pci_probe+0x5f/0xd0
                                           [<ffffffff812dfde9>] pci_device_probe+0x119/0x120
                                           [<ffffffff81373df6>] driver_probe_device+0x96/0x1c0
                                           [<ffffffff81373fcb>] __driver_attach+0xab/0xb0
                                           [<ffffffff81372a1e>] bus_for_each_dev+0x5e/0x90
                                           [<ffffffff81373a2e>] driver_attach+0x1e/0x20
                                           [<ffffffff813735b8>] bus_add_driver+0xc8/0x290
                                           [<ffffffff813745b6>] driver_register+0x76/0x140
                                           [<ffffffff812e0046>] __pci_register_driver+0x66/0xe0
                                           [<ffffffffa001b03a>] serio_raw_poll+0x3a/0x60 [serio_raw]
                                           [<ffffffff81002165>] do_one_initcall+0x45/0x190
                                           [<ffffffff810aa76b>] sys_init_module+0xfb/0x250
                                           [<ffffffff8157a142>] system_call_fastpath+0x16/0x1b
    }
    ... key      at: [<ffffffffa0017590>] __key.42516+0x0/0xffffffffffffda70 [vmxnet3]
    ... acquired at:
    [<ffffffff8109ca4d>] lock_acquire+0x9d/0x130
    [<ffffffff81571bb5>] _raw_spin_lock_irqsave+0x55/0xa0
    [<ffffffffa000de27>] vmxnet3_set_mc+0x97/0x1a0 [vmxnet3]
    [<ffffffff8146ffa0>] __dev_set_rx_mode+0x40/0xb0
    [<ffffffff81470040>] dev_set_rx_mode+0x30/0x50
    [<ffffffff81470127>] __dev_open+0xc7/0x100
    [<ffffffff814703c1>] __dev_change_flags+0xa1/0x180
    [<ffffffff81470568>] dev_change_flags+0x28/0x70
    [<ffffffff814da960>] devinet_ioctl+0x730/0x800
    [<ffffffff814db508>] inet_ioctl+0x88/0xa0
    [<ffffffff814541f0>] sock_do_ioctl+0x30/0x70
    [<ffffffff814542a9>] sock_ioctl+0x79/0x2f0
    [<ffffffff81188798>] do_vfs_ioctl+0x98/0x570
    [<ffffffff81188d01>] sys_ioctl+0x91/0xa0
    [<ffffffff8157a142>] system_call_fastpath+0x16/0x1b

  -> (_xmit_ETHER){+.....} ops: 6 {
     HARDIRQ-ON-W at:
                                          [<ffffffff8109ad86>] __lock_acquire+0x7f6/0x1e10
                                          [<ffffffff8109ca4d>] lock_acquire+0x9d/0x130
                                          [<ffffffff8157124b>] _raw_spin_lock_bh+0x3b/0x70
                                          [<ffffffff81475618>] __dev_mc_add+0x38/0x90
                                          [<ffffffff814756a0>] dev_mc_add+0x10/0x20
                                          [<ffffffff81532c9e>] igmp6_group_added+0x10e/0x1b0
                                          [<ffffffff81533f2d>] ipv6_dev_mc_inc+0x2cd/0x430
                                          [<ffffffff81515e17>] ipv6_add_dev+0x357/0x450
                                          [<ffffffff81519f27>] addrconf_notify+0x2f7/0xb10
                                          [<ffffffff81575c1c>] notifier_call_chain+0x8c/0xc0
                                          [<ffffffff81089586>] raw_notifier_call_chain+0x16/0x20
                                          [<ffffffff814689b7>] call_netdevice_notifiers+0x37/0x70
                                          [<ffffffff8146a944>] register_netdevice+0x244/0x2d0
                                          [<ffffffff8146aa0f>] register_netdev+0x3f/0x60
                                          [<ffffffffa001419b>] vmxnet3_probe_device+0x760/0x15c5 [vmxnet3]
                                          [<ffffffff812df67f>] local_pci_probe+0x5f/0xd0
                                          [<ffffffff812dfde9>] pci_device_probe+0x119/0x120
                                          [<ffffffff81373df6>] driver_probe_device+0x96/0x1c0
                                          [<ffffffff81373fcb>] __driver_attach+0xab/0xb0
                                          [<ffffffff81372a1e>] bus_for_each_dev+0x5e/0x90
                                          [<ffffffff81373a2e>] driver_attach+0x1e/0x20
                                          [<ffffffff813735b8>] bus_add_driver+0xc8/0x290
                                          [<ffffffff813745b6>] driver_register+0x76/0x140
                                          [<ffffffff812e0046>] __pci_register_driver+0x66/0xe0
                                          [<ffffffffa001b03a>] serio_raw_poll+0x3a/0x60 [serio_raw]
                                          [<ffffffff81002165>] do_one_initcall+0x45/0x190
                                          [<ffffffff810aa76b>] sys_init_module+0xfb/0x250
                                          [<ffffffff8157a142>] system_call_fastpath+0x16/0x1b
     INITIAL USE at:
                                         [<ffffffff8109a9e9>] __lock_acquire+0x459/0x1e10
                                         [<ffffffff8109ca4d>] lock_acquire+0x9d/0x130
                                         [<ffffffff8157124b>] _raw_spin_lock_bh+0x3b/0x70
                                         [<ffffffff81475618>] __dev_mc_add+0x38/0x90
                                         [<ffffffff814756a0>] dev_mc_add+0x10/0x20
                                         [<ffffffff81532c9e>] igmp6_group_added+0x10e/0x1b0
                                         [<ffffffff81533f2d>] ipv6_dev_mc_inc+0x2cd/0x430
                                         [<ffffffff81515e17>] ipv6_add_dev+0x357/0x450
                                         [<ffffffff81519f27>] addrconf_notify+0x2f7/0xb10
                                         [<ffffffff81575c1c>] notifier_call_chain+0x8c/0xc0
                                         [<ffffffff81089586>] raw_notifier_call_chain+0x16/0x20
                                         [<ffffffff814689b7>] call_netdevice_notifiers+0x37/0x70
                                         [<ffffffff8146a944>] register_netdevice+0x244/0x2d0
                                         [<ffffffff8146aa0f>] register_netdev+0x3f/0x60
                                         [<ffffffffa001419b>] vmxnet3_probe_device+0x760/0x15c5 [vmxnet3]
                                         [<ffffffff812df67f>] local_pci_probe+0x5f/0xd0
                                         [<ffffffff812dfde9>] pci_device_probe+0x119/0x120
                                         [<ffffffff81373df6>] driver_probe_device+0x96/0x1c0
                                         [<ffffffff81373fcb>] __driver_attach+0xab/0xb0
                                         [<ffffffff81372a1e>] bus_for_each_dev+0x5e/0x90
                                         [<ffffffff81373a2e>] driver_attach+0x1e/0x20
                                         [<ffffffff813735b8>] bus_add_driver+0xc8/0x290
                                         [<ffffffff813745b6>] driver_register+0x76/0x140
                                         [<ffffffff812e0046>] __pci_register_driver+0x66/0xe0
                                         [<ffffffffa001b03a>] serio_raw_poll+0x3a/0x60 [serio_raw]
                                         [<ffffffff81002165>] do_one_initcall+0x45/0x190
                                         [<ffffffff810aa76b>] sys_init_module+0xfb/0x250
                                         [<ffffffff8157a142>] system_call_fastpath+0x16/0x1b
   }
   ... key      at: [<ffffffff827fd868>] netdev_addr_lock_key+0x8/0x1e0
   ... acquired at:
    [<ffffffff8109ca4d>] lock_acquire+0x9d/0x130
    [<ffffffff8157124b>] _raw_spin_lock_bh+0x3b/0x70
    [<ffffffff81475618>] __dev_mc_add+0x38/0x90
    [<ffffffff814756a0>] dev_mc_add+0x10/0x20
    [<ffffffff81532c9e>] igmp6_group_added+0x10e/0x1b0
    [<ffffffff81533f2d>] ipv6_dev_mc_inc+0x2cd/0x430
    [<ffffffff81515e17>] ipv6_add_dev+0x357/0x450
    [<ffffffff81519f27>] addrconf_notify+0x2f7/0xb10
    [<ffffffff81575c1c>] notifier_call_chain+0x8c/0xc0
    [<ffffffff81089586>] raw_notifier_call_chain+0x16/0x20
    [<ffffffff814689b7>] call_netdevice_notifiers+0x37/0x70
    [<ffffffff8146a944>] register_netdevice+0x244/0x2d0
    [<ffffffff8146aa0f>] register_netdev+0x3f/0x60
    [<ffffffffa001419b>] vmxnet3_probe_device+0x760/0x15c5 [vmxnet3]
    [<ffffffff812df67f>] local_pci_probe+0x5f/0xd0
    [<ffffffff812dfde9>] pci_device_probe+0x119/0x120
    [<ffffffff81373df6>] driver_probe_device+0x96/0x1c0
    [<ffffffff81373fcb>] __driver_attach+0xab/0xb0
    [<ffffffff81372a1e>] bus_for_each_dev+0x5e/0x90
    [<ffffffff81373a2e>] driver_attach+0x1e/0x20
    [<ffffffff813735b8>] bus_add_driver+0xc8/0x290
    [<ffffffff813745b6>] driver_register+0x76/0x140
    [<ffffffff812e0046>] __pci_register_driver+0x66/0xe0
    [<ffffffffa001b03a>] serio_raw_poll+0x3a/0x60 [serio_raw]
    [<ffffffff81002165>] do_one_initcall+0x45/0x190
    [<ffffffff810aa76b>] sys_init_module+0xfb/0x250
    [<ffffffff8157a142>] system_call_fastpath+0x16/0x1b

 -> (&(&mc->mca_lock)->rlock){+.-...} ops: 6 {
    HARDIRQ-ON-W at:
                                        [<ffffffff8109ad86>] __lock_acquire+0x7f6/0x1e10
                                        [<ffffffff8109ca4d>] lock_acquire+0x9d/0x130
                                        [<ffffffff8157124b>] _raw_spin_lock_bh+0x3b/0x70
                                        [<ffffffff81532bd5>] igmp6_group_added+0x45/0x1b0
                                        [<ffffffff81533f2d>] ipv6_dev_mc_inc+0x2cd/0x430
                                        [<ffffffff81515e17>] ipv6_add_dev+0x357/0x450
                                        [<ffffffff81ce0d16>] addrconf_init+0x4e/0x183
                                        [<ffffffff81ce0ba1>] inet6_init+0x191/0x2a6
                                        [<ffffffff81002165>] do_one_initcall+0x45/0x190
                                        [<ffffffff81ca4d3f>] kernel_init+0xe3/0x168
                                        [<ffffffff8157b2e4>] kernel_thread_helper+0x4/0x10
    IN-SOFTIRQ-W at:
                                        [<ffffffff8109ad5e>] __lock_acquire+0x7ce/0x1e10
                                        [<ffffffff8109ca4d>] lock_acquire+0x9d/0x130
                                        [<ffffffff8157124b>] _raw_spin_lock_bh+0x3b/0x70
                                        [<ffffffff81531e9f>] mld_ifc_timer_expire+0xff/0x280
                                        [<ffffffff8106f2a9>] run_timer_softirq+0x179/0x3f0
                                        [<ffffffff810666d0>] __do_softirq+0xc0/0x210
                                        [<ffffffff8157b3dc>] call_softirq+0x1c/0x30
                                        [<ffffffff8100d42d>] do_softirq+0xad/0xe0
                                        [<ffffffff81066afe>] irq_exit+0x9e/0xb0
                                        [<ffffffff8157bd40>] smp_apic_timer_interrupt+0x70/0x9b
                                        [<ffffffff8157ab93>] apic_timer_interrupt+0x13/0x20
                                        [<ffffffff8149d857>] rt_do_flush+0x87/0x2a0
                                        [<ffffffff814a16b6>] rt_cache_flush+0x46/0x60
                                        [<ffffffff814e36e0>] fib_disable_ip+0x40/0x60
                                        [<ffffffff814e5447>] fib_inetaddr_event+0xd7/0xe0
                                        [<ffffffff81575c1c>] notifier_call_chain+0x8c/0xc0
                                        [<ffffffff810896e8>] __blocking_notifier_call_chain+0x78/0xb0
                                        [<ffffffff81089736>] blocking_notifier_call_chain+0x16/0x20
                                        [<ffffffff814d8021>] __inet_del_ifa+0xf1/0x2e0
                                        [<ffffffff814d8223>] inet_del_ifa+0x13/0x20
                                        [<ffffffff814da731>] devinet_ioctl+0x501/0x800
                                        [<ffffffff814db508>] inet_ioctl+0x88/0xa0
                                        [<ffffffff814541f0>] sock_do_ioctl+0x30/0x70
                                        [<ffffffff814542a9>] sock_ioctl+0x79/0x2f0
                                        [<ffffffff81188798>] do_vfs_ioctl+0x98/0x570
                                        [<ffffffff81188d01>] sys_ioctl+0x91/0xa0
                                        [<ffffffff8157a142>] system_call_fastpath+0x16/0x1b
    INITIAL USE at:
                                       [<ffffffff8109a9e9>] __lock_acquire+0x459/0x1e10
                                       [<ffffffff8109ca4d>] lock_acquire+0x9d/0x130
                                       [<ffffffff8157124b>] _raw_spin_lock_bh+0x3b/0x70
                                       [<ffffffff81532bd5>] igmp6_group_added+0x45/0x1b0
                                       [<ffffffff81533f2d>] ipv6_dev_mc_inc+0x2cd/0x430
                                       [<ffffffff81515e17>] ipv6_add_dev+0x357/0x450
                                       [<ffffffff81ce0d16>] addrconf_init+0x4e/0x183
                                       [<ffffffff81ce0ba1>] inet6_init+0x191/0x2a6
                                       [<ffffffff81002165>] do_one_initcall+0x45/0x190
                                       [<ffffffff81ca4d3f>] kernel_init+0xe3/0x168
                                       [<ffffffff8157b2e4>] kernel_thread_helper+0x4/0x10
  }
  ... key      at: [<ffffffff82801be2>] __key.40877+0x0/0x8
  ... acquired at:
    [<ffffffff810997bc>] check_usage_forwards+0x9c/0x110
    [<ffffffff8109a32c>] mark_lock+0x19c/0x400
    [<ffffffff8109ad5e>] __lock_acquire+0x7ce/0x1e10
    [<ffffffff8109ca4d>] lock_acquire+0x9d/0x130
    [<ffffffff8157124b>] _raw_spin_lock_bh+0x3b/0x70
    [<ffffffff81531e9f>] mld_ifc_timer_expire+0xff/0x280
    [<ffffffff8106f2a9>] run_timer_softirq+0x179/0x3f0
    [<ffffffff810666d0>] __do_softirq+0xc0/0x210
    [<ffffffff8157b3dc>] call_softirq+0x1c/0x30
    [<ffffffff8100d42d>] do_softirq+0xad/0xe0
    [<ffffffff81066afe>] irq_exit+0x9e/0xb0
    [<ffffffff8157bd40>] smp_apic_timer_interrupt+0x70/0x9b
    [<ffffffff8157ab93>] apic_timer_interrupt+0x13/0x20
    [<ffffffff8149d857>] rt_do_flush+0x87/0x2a0
    [<ffffffff814a16b6>] rt_cache_flush+0x46/0x60
    [<ffffffff814e36e0>] fib_disable_ip+0x40/0x60
    [<ffffffff814e5447>] fib_inetaddr_event+0xd7/0xe0
    [<ffffffff81575c1c>] notifier_call_chain+0x8c/0xc0
    [<ffffffff810896e8>] __blocking_notifier_call_chain+0x78/0xb0
    [<ffffffff81089736>] blocking_notifier_call_chain+0x16/0x20
    [<ffffffff814d8021>] __inet_del_ifa+0xf1/0x2e0
    [<ffffffff814d8223>] inet_del_ifa+0x13/0x20
    [<ffffffff814da731>] devinet_ioctl+0x501/0x800
    [<ffffffff814db508>] inet_ioctl+0x88/0xa0
    [<ffffffff814541f0>] sock_do_ioctl+0x30/0x70
    [<ffffffff814542a9>] sock_ioctl+0x79/0x2f0
    [<ffffffff81188798>] do_vfs_ioctl+0x98/0x570
    [<ffffffff81188d01>] sys_ioctl+0x91/0xa0
    [<ffffffff8157a142>] system_call_fastpath+0x16/0x1b

 stack backtrace:
 Pid: 567, comm: ifconfig Not tainted 2.6.39-rc6+ #1
 Call Trace:
  <IRQ>  [<ffffffff810996f6>] print_irq_inversion_bug+0x146/0x170
  [<ffffffff81099720>] ? print_irq_inversion_bug+0x170/0x170
  [<ffffffff810997bc>] check_usage_forwards+0x9c/0x110
  [<ffffffff8109a32c>] mark_lock+0x19c/0x400
  [<ffffffff8109ad5e>] __lock_acquire+0x7ce/0x1e10
  [<ffffffff8109a383>] ? mark_lock+0x1f3/0x400
  [<ffffffff8109b497>] ? __lock_acquire+0xf07/0x1e10
  [<ffffffff81012255>] ? native_sched_clock+0x15/0x70
  [<ffffffff8109ca4d>] lock_acquire+0x9d/0x130
  [<ffffffff81531e9f>] ? mld_ifc_timer_expire+0xff/0x280
  [<ffffffff8109759d>] ? lock_release_holdtime+0x3d/0x1a0
  [<ffffffff8157124b>] _raw_spin_lock_bh+0x3b/0x70
  [<ffffffff81531e9f>] ? mld_ifc_timer_expire+0xff/0x280
  [<ffffffff8157170b>] ? _raw_spin_unlock+0x2b/0x40
  [<ffffffff81531e9f>] mld_ifc_timer_expire+0xff/0x280
  [<ffffffff8106f2a9>] run_timer_softirq+0x179/0x3f0
  [<ffffffff8106f21b>] ? run_timer_softirq+0xeb/0x3f0
  [<ffffffff810122b9>] ? sched_clock+0x9/0x10
  [<ffffffff81531da0>] ? mld_gq_timer_expire+0x30/0x30
  [<ffffffff810666d0>] __do_softirq+0xc0/0x210
  [<ffffffff8109455f>] ? tick_program_event+0x1f/0x30
  [<ffffffff8157b3dc>] call_softirq+0x1c/0x30
  [<ffffffff8100d42d>] do_softirq+0xad/0xe0
  [<ffffffff81066afe>] irq_exit+0x9e/0xb0
  [<ffffffff8157bd40>] smp_apic_timer_interrupt+0x70/0x9b
  [<ffffffff8157ab93>] apic_timer_interrupt+0x13/0x20
  <EOI>  [<ffffffff81571f14>] ? retint_restore_args+0x13/0x13
  [<ffffffff810974a7>] ? lock_is_held+0x17/0xd0
  [<ffffffff8149d857>] rt_do_flush+0x87/0x2a0
  [<ffffffff814a16b6>] rt_cache_flush+0x46/0x60
  [<ffffffff814e36e0>] fib_disable_ip+0x40/0x60
  [<ffffffff814e5447>] fib_inetaddr_event+0xd7/0xe0
  [<ffffffff81575c1c>] notifier_call_chain+0x8c/0xc0
  [<ffffffff810896e8>] __blocking_notifier_call_chain+0x78/0xb0
  [<ffffffff81089736>] blocking_notifier_call_chain+0x16/0x20
  [<ffffffff814d8021>] __inet_del_ifa+0xf1/0x2e0
  [<ffffffff814d8223>] inet_del_ifa+0x13/0x20
  [<ffffffff814da731>] devinet_ioctl+0x501/0x800
  [<ffffffff8108a3af>] ? local_clock+0x6f/0x80
  [<ffffffff81575898>] ? do_page_fault+0x268/0x560
  [<ffffffff814db508>] inet_ioctl+0x88/0xa0
  [<ffffffff814541f0>] sock_do_ioctl+0x30/0x70
  [<ffffffff814542a9>] sock_ioctl+0x79/0x2f0
  [<ffffffff810dfe87>] ? __call_rcu+0xa7/0x190
  [<ffffffff81188798>] do_vfs_ioctl+0x98/0x570
  [<ffffffff8117737e>] ? fget_light+0x33e/0x430
  [<ffffffff81571ef9>] ? retint_swapgs+0x13/0x1b
  [<ffffffff81188d01>] sys_ioctl+0x91/0xa0
  [<ffffffff8157a142>] system_call_fastpath+0x16/0x1b
Signed-off-by: NRoland Dreier <roland@purestorage.com>
Signed-off-by: NShreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: NScott J. Goldman <scottjg@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TX checksumming support has been ifdef commented out of this driver
for more than 10 years, and it makes references to aspects of the IPv4
stack from back then as well.

If someone has one of these rare cards and wants to properly resurrect
TX checksumming support, they can still get at this code in the
version control history.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RTR frames do have a valid data length code on CAN.
The driver for SJA1000 did not handle that situation properly.
Signed-off-by: NKurt Van Dijck <kurt.van.dijck@eia.be>
Acked-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Force dev_alloc_name() to be called from register_netdevice() by
dev_get_valid_name(). That allows to remove multiple explicit
dev_alloc_name() calls.

The possibility to call dev_alloc_name in advance remains.

This also fixes veth creation regresion caused by
84c49d8cSigned-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>