This patch adds a generic variant of
amd_iommu_flush_all_devices function which flushes only the
DTEs for a given protection domain.
Signed-off-by: NJoerg Roedel <joerg.roedel@amd.com>

Don't reimplement the page table walker in this function.
Use the generic one.
Signed-off-by: NJoerg Roedel <joerg.roedel@amd.com>

Instead of reimplementing existing logic use fetch_pte to
walk the page table in iommu_unmap_page.
Signed-off-by: NJoerg Roedel <joerg.roedel@amd.com>

This patch changes the fetch_pte function in the AMD IOMMU
driver to support dynamic mapping levels.
Signed-off-by: NJoerg Roedel <joerg.roedel@amd.com>

2.6.31-rc7 does not boot on vSMP systems:

[    8.501108] CPU31: Thermal monitoring enabled (TM1)
[    8.501127] CPU 31 MCA banks SHD:2 SHD:3 SHD:5 SHD:6 SHD:8
[    8.650254] CPU31: Intel(R) Xeon(R) CPU           E5540  @ 2.53GHz stepping 04
[    8.710324] Brought up 32 CPUs
[    8.713916] Total of 32 processors activated (162314.96 BogoMIPS).
[    8.721489] ERROR: parent span is not a superset of domain->span
[    8.727686] ERROR: domain->groups does not contain CPU0
[    8.733091] ERROR: groups don't span domain->span
[    8.737975] ERROR: domain->cpu_power not set
[    8.742416]

Ravikiran Thirumalai bisected it to:

| commit 2759c328
| x86: don't call read_apic_id if !cpu_has_apic

The problem is that on vSMP systems the CPUID derived
initial-APICIDs are overlapping - so we need to fall
back on hard_smp_processor_id() which reads the local
APIC.

Both come from the hardware (influenced by firmware
though) so it's a tough call which one to trust.

Doing the quirk expresses the vSMP property properly
and also does not affect other systems, so we go for
this solution instead of a revert.
Reported-and-Tested-by: NRavikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Shai Fultheim <shai@scalex86.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <4A944D3C.5030100@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

binutils prior to 2.17 can't deal with the currently possible
situation of a new segment following the per-CPU segment, but
that new segment being empty - objcopy misplaces the .bss (and
perhaps also the .brk) sections outside of any segment.

However, the current ordering of sections really just appears
to be the effect of cumulative unrelated changes; re-ordering
things allows to easily guarantee that the segment following
the per-CPU one is non-empty, and at once eliminates the need
for the bogus data.init2 segment.

Once touching this code, also use the various data section
helper macros from include/asm-generic/vmlinux.lds.h.

-v2: fix !SMP builds.
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Cc: <sam@ravnborg.org>
LKML-Reference: <4A94085D02000078000119A5@vpn.id2.novell.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

The default_send_IPI_mask_logical() function uses the "flat" APIC mode
to send an IPI to a set of CPU's at once, but if that set happens to be
empty, some older local APIC's will apparently be rather unhappy.  So
just warn if a caller gives us an empty mask, and ignore it.

This fixes a regression in 2.6.30.x, due to commit 4595f962 ("x86:
change flush_tlb_others to take a const struct cpumask"), documented
here:

	http://bugzilla.kernel.org/show_bug.cgi?id=13933

which causes a silent lock-up.  It only seems to happen on PPro, P2, P3
and Athlon XP cores.  Most developers sadly (or not so sadly, if you're
a developer..) have more modern CPU's.  Also, on x86-64 we don't use the
flat APIC mode, so it would never trigger there even if the APIC didn't
like sending an empty IPI mask.
Reported-by: NPavel Vilim <wylda@volny.cz>
Reported-and-tested-by: NThomas Björnell <thomas.bjornell@gmail.com>
Reported-and-tested-by: NMartin Rogge <marogge@onlinehome.de>
Cc: Mike Travis <travis@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: stable@kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

load_percpu_segment() is used to set up the per-cpu segment registers,
which are also used for -fstack-protector.  Make sure that the
load_percpu_segment() function doesn't have stackprotector enabled.

[ Impact: allow percpu setup before calling stack-protected functions ]
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>

Currently clockevents_notify() is called with interrupts enabled at
some places and interrupts disabled at some other places.

This results in a deadlock in this scenario.

cpu A holds clockevents_lock in clockevents_notify() with irqs enabled
cpu B waits for clockevents_lock in clockevents_notify() with irqs disabled
cpu C doing set_mtrr() which will try to rendezvous of all the cpus.

This will result in C and A come to the rendezvous point and waiting
for B. B is stuck forever waiting for the spinlock and thus not
reaching the rendezvous point.

Fix the clockevents code so that clockevents_lock is taken with
interrupts disabled and thus avoid the above deadlock.

Also call lapic_timer_propagate_broadcast() on the destination cpu so
that we avoid calling smp_call_function() in the clockevents notifier
chain.

This issue left us wondering if we need to change the MTRR rendezvous
logic to use stop machine logic (instead of smp_call_function) or add
a check in spinlock debug code to see if there are other spinlocks
which gets taken under both interrupts enabled/disabled conditions.
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: "Pallipadi Venkatesh" <venkatesh.pallipadi@intel.com>
Cc: "Brown Len" <len.brown@intel.com>
LKML-Reference: <1250544899.2709.210.camel@sbs-t61.sc.intel.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Commit 0e83815b changed the
section the initial_code variable gets allocated in, in an
attempt to address a section conflict warning. This, however
created a new section conflict when building without
HOTPLUG_CPU. The apparently only (reasonable) way to address
this is to always use __REFDATA.

Once at it, also fix a second section mismatch when not using
HOTPLUG_CPU.
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Cc: Robert Richter <robert.richter@amd.com>
LKML-Reference: <4A8AE7CD020000780001054B@vpn.id2.novell.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

An older test-box started hanging at the following point during
bootup:

 [    0.022996] Mount-cache hash table entries: 512
 [    0.024996] Initializing cgroup subsys debug
 [    0.025996] Initializing cgroup subsys cpuacct
 [    0.026995] Initializing cgroup subsys devices
 [    0.027995] Initializing cgroup subsys freezer
 [    0.028995] mce: CPU supports 5 MCE banks

I've bisected it down to commit 4efc0670 ("x86, mce: use 64bit
machine check code on 32bit"), which utilizes the MCE code on
32-bit systems too.

The problem is caused by this detail in my config:

  # CONFIG_CPU_SUP_INTEL is not set

This disables the quirks in mce_cpu_quirks() but still enables
MCE support - which then hangs due to the missing quirk
workaround needed on this CPU:

	if (c->x86 == 6 && c->x86_model < 0x1A && banks > 0)
		mce_banks[0].init = 0;

The safe solution is to not initialize MCEs if we dont know on
what CPU we are running (or if that CPU's support code got
disabled in the config).

Also be a bit more defensive on 32-bit systems: dont do a
boot-time dump of pending MCEs not just on the specific system
that we found a problem with (Pentium-M), but earlier ones as
well.

Now this problem is probably not common and disabling CPU
support is rare - but still being more defensive in something
we turned on for a wide range of CPUs is prudent.

Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
LKML-Reference: Message-ID: <4A88E3E4.40506@jp.fujitsu.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

On my legacy Pentium M laptop (Acer Extensa 2900) I get bogus MCE on a cold
boot with CONFIG_X86_NEW_MCE enabled, i.e. (after decoding it with mcelog):

MCE 0
HARDWARE ERROR. This is *NOT* a software problem!
Please contact your hardware vendor
CPU 0 BANK 1 MCG status:
MCi status:
Error overflow
Uncorrected error
Error enabled
Processor context corrupt
MCA: Data CACHE Level-1 UNKNOWN Error
STATUS f200000000000195 MCGSTATUS 0

[ The other STATUS values observed: f2000000000001b5 (... UNKNOWN error)
  and f200000000000115 (... READ Error).

  To verify that this is not a CONFIG_X86_NEW_MCE bug I also modified
  the CONFIG_X86_OLD_MCE code (which doesn't log any MCEs) to dump
  content of STATUS MSR before it is cleared during initialization. ]

Since the bogus MCE results in a kernel taint (which in turn disables
lockdep support) don't log boot MCEs on Pentium M (model == 13) CPUs
by default ("mce=bootlog" boot parameter can be be used to get the old
behavior).
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Reviewed-by: NAndi Kleen <andi@firstfloor.org>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

The function uv_acpi_madt_oem_check() has been marked __init,
the struct apic_x2apic_uv_x has been marked __refdata.

The aim is to address the following section mismatch messages:

WARNING: arch/x86/kernel/apic/built-in.o(.data+0x1368): Section mismatch in reference from the variable apic_x2apic_uv_x to the function .cpuinit.text:uv_wakeup_secondary()
The variable apic_x2apic_uv_x references
the function __cpuinit uv_wakeup_secondary()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,

WARNING: arch/x86/kernel/built-in.o(.data+0x68e8): Section mismatch in reference from the variable apic_x2apic_uv_x to the function .cpuinit.text:uv_wakeup_secondary()
The variable apic_x2apic_uv_x references
the function __cpuinit uv_wakeup_secondary()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,

WARNING: arch/x86/built-in.o(.text+0x7b36f): Section mismatch in reference from the function uv_acpi_madt_oem_check() to the function .init.text:early_ioremap()
The function uv_acpi_madt_oem_check() references
the function __init early_ioremap().
This is often because uv_acpi_madt_oem_check lacks a __init
annotation or the annotation of early_ioremap is wrong.

WARNING: arch/x86/built-in.o(.text+0x7b38d): Section mismatch in reference from the function uv_acpi_madt_oem_check() to the function .init.text:early_iounmap()
The function uv_acpi_madt_oem_check() references
the function __init early_iounmap().
This is often because uv_acpi_madt_oem_check lacks a __init
annotation or the annotation of early_iounmap is wrong.

WARNING: arch/x86/built-in.o(.data+0x8668): Section mismatch in reference from the variable apic_x2apic_uv_x to the function .cpuinit.text:uv_wakeup_secondary()
The variable apic_x2apic_uv_x references
the function __cpuinit uv_wakeup_secondary()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: NLeonardo Potenza <lpotenza@inwind.it>
LKML-Reference: <200908161855.48302.lpotenza@inwind.it>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

0d01f314 "x86, mce: therm_throt
- change when we print messages" removed redundant
announcements of "Temperature/speed normal".

They're not worth logging and remove their accompanying
"Machine check events logged" messages as well from the
console.
Signed-off-by: NHugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
LKML-Reference: <Pine.LNX.4.64.0908161544100.7929@sister.anvils>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

The SGI UV Broadcast Assist Unit is used to send TLB shootdown
messages to remote nodes of the system.  The header of the
message must contain the subnode id of the block in the
receiving hub that handles such messages.  It should always be
0x10, the id of the "LB" block.

It had previously been documented as a "must be zero" field.
Signed-off-by: NCliff Wickman <cpw@sgi.com>
Acked-by: NJack Steiner <steiner@sgi.com>
LKML-Reference: <E1Mc1x7-0005Ce-6t@eag09.americas.sgi.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

percpu code has been assuming num_possible_cpus() == nr_cpu_ids which
is incorrect if cpu_possible_map contains holes.  This causes percpu
code to access beyond allocated memories and vmalloc areas.  On a
sparc64 machine with cpus 0 and 2 (u60), this triggers the following
warning or fails boot.

 WARNING: at /devel/tj/os/work/mm/vmalloc.c:106 vmap_page_range_noflush+0x1f0/0x240()
 Modules linked in:
 Call Trace:
  [00000000004b17d0] vmap_page_range_noflush+0x1f0/0x240
  [00000000004b1840] map_vm_area+0x20/0x60
  [00000000004b1950] __vmalloc_area_node+0xd0/0x160
  [0000000000593434] deflate_init+0x14/0xe0
  [0000000000583b94] __crypto_alloc_tfm+0xd4/0x1e0
  [00000000005844f0] crypto_alloc_base+0x50/0xa0
  [000000000058b898] alg_test_comp+0x18/0x80
  [000000000058dad4] alg_test+0x54/0x180
  [000000000058af00] cryptomgr_test+0x40/0x60
  [0000000000473098] kthread+0x58/0x80
  [000000000042b590] kernel_thread+0x30/0x60
  [0000000000472fd0] kthreadd+0xf0/0x160
 ---[ end trace 429b268a213317ba ]---

This patch fixes generic percpu functions and sparc64
setup_per_cpu_areas() so that they handle sparse cpu_possible_map
properly.

Please note that on x86, cpu_possible_map() doesn't contain holes and
thus num_possible_cpus() == nr_cpu_ids and this patch doesn't cause
any behavior difference.
Signed-off-by: NTejun Heo <tj@kernel.org>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Cc: Ingo Molnar <mingo@elte.hu>

Johannes Stezenbach reported that his Pentium-M based
laptop does not have the local APIC enabled by default,
and hence perfcounters do not get initialized.

Add a fallback for this case: allow non-sampled counters
and return with an error on sampled counters. This allows
'perf stat' to work out of box - and allows 'perf top'
and 'perf record' to fall back on a hrtimer based sampling
method.

( Passing 'lapic' on the boot line will allow hardware
  sampling to occur - but if the APIC is disabled
  permanently by the hardware then this fallback still
  allows more systems to use perfcounters. )

Also decouple perfcounter support from X86_LOCAL_APIC.

-v2: fix typo breaking counters on all other systems ...
Reported-by: NJohannes Stezenbach <js@sig21.net>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Kernel is broken for x86 CPUs without CPUID since 2.6.28. It
crashes with NULL pointer dereference in identify_cpu():

766        generic_identify(c);
767
768-->     if (this_cpu->c_identify)
769               this_cpu->c_identify(c);

this_cpu is NULL. This is because it's only initialized in
get_cpu_vendor() function, which is not called if the CPU has
no CPUID instruction.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
LKML-Reference: <200908112000.15993.linux@rainbow-software.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Due to an erratum with certain AMD Athlon 64 processors, the
BIOS may need to force enable the LAHF_LM capability.
Unfortunately, in at least one case, the BIOS does this even
for processors that do not support the functionality.

Add a specific check that will clear the feature bit for
processors known not to support the LAHF/SAHF instructions.
Signed-off-by: NKevin Winchester <kjwinchester@gmail.com>
Acked-by: NBorislav Petkov <petkovbb@googlemail.com>
LKML-Reference: <4A80A5AD.2000209@gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Johannes Stezenbach reported that 'perf stat' does not count
cache-miss and cache-references events on his Pentium-M based
laptop.

This is because we left them blank in p6_perfmon_event_map[],
fill them in.
Reported-by: NJohannes Stezenbach <js@sig21.net>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Instead of this garbled bootup on UP Pentium-M systems:

[    0.015048] Performance Counters:
[    0.016004] no Local APIC, try rebooting with lapicno PMU driver, software counters only.

Print:

[    0.015050] Performance Counters:
[    0.016004] no APIC, boot with the "lapic" boot parameter to force-enable it.
[    0.017003] no PMU driver, software counters only.

Cf: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

My Latitude d630 seems to be handling thermal events in SMI by
lowering the max frequency of the CPU till it cools down but
still leaks the "everything is normal" events.

This spams the console and with high priority printks.

Adjust therm_throt driver to only print messages about the fact
that temperatire returned back to normal when leaving the
throttling state.

Also lower the severity of "back to normal" message from
KERN_CRIT to KERN_INFO.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
Acked-by: NH. Peter Anvin <hpa@zytor.com>
LKML-Reference: <20090810051513.0558F526EC9@mailhub.coreip.homeip.net>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Reboot does not work on my MacBook Pro 13 inch (MacBookPro5,5)
too. It seems all unibody MacBook and MacBookPro require
PCI reboot handling, i guess.

Following model/machine ID list shows unibody MacBook/Pro have
the 5 series of model number:

   http://www.everymac.com/systems/by_capability/macs-by-machine-model-machine-id.htmlSigned-off-by: NShunichi Fuji <palglowr@gmail.com>
Cc: Ozan Çağlayan <ozan@pardus.org.tr>
LKML-Reference: <30046e3b0908101134p6487ddbftd8776e4ddef204be@mail.gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Wei Chong Tan reported a fast-PIT-calibration corner-case:

| pit_expect_msb() is vulnerable to SMI disturbance corner case
| in some platforms which causes /proc/cpuinfo to show wrong
| CPU MHz value when quick_pit_calibrate() jumps to success
| section.

I think that the real issue isn't even an SMI - but the fact
that in the very last iteration of the loop, there's no
serializing instruction _after_ the last 'rdtsc'. So even in
the absense of SMI's, we do have a situation where the cycle
counter was read without proper serialization.

The last check should be done outside the outer loop, since
_inside_ the outer loop, we'll be testing that the PIT has
the right MSB value has the right value in the next iteration.

So only the _last_ iteration is special, because that's the one
that will not check the PIT MSB value any more, and because the
final 'get_cycles()' isn't serialized.

In other words:

 - I'd like to move the PIT MSB check to after the last
   iteration, rather than in every iteration

 - I think we should comment on the fact that it's also a
   serializing instruction and so 'fences in' the TSC read.

Here's a suggested replacement.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
Reported-by: N"Tan, Wei Chong" <wei.chong.tan@intel.com>
Tested-by: N"Tan, Wei Chong" <wei.chong.tan@intel.com>
LKML-Reference: <B28277FD4E0F9247A3D55704C440A140D5D683F3@pgsmsx504.gar.corp.intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

If the vendor name (from c16) can be longer than 100 bytes (or missing a
terminating null), then the null is written past the end of vendor[].

Found with Parfait, http://research.sun.com/projects/parfait/Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>
Cc: Huang Ying <ying.huang@intel.com>

MacBookPro5,1 is not able to reboot unless reboot=pci is set.
This patch forces it through a DMI quirk specific to this
device.
Signed-off-by: NOzan Çağlayan <ozan@pardus.org.tr>
LKML-Reference: <1249403971-6543-1-git-send-email-ozan@pardus.org.tr>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

found a system where x2apic reports an MSI-X irq initialization
failure:

[  302.859446] igbvf 0000:81:10.4: enabling device (0000 -> 0002)
[  302.874369] igbvf 0000:81:10.4: using 64bit DMA mask
[  302.879023] igbvf 0000:81:10.4: using 64bit consistent DMA mask
[  302.894386] igbvf 0000:81:10.4: enabling bus mastering
[  302.898171] igbvf 0000:81:10.4: setting latency timer to 64
[  302.914050] reserve_memtype added 0xefb08000-0xefb0c000, track uncached-minus, req uncached-minus, ret uncached-minus
[  302.933839] reserve_memtype added 0xefb28000-0xefb29000, track uncached-minus, req uncached-minus, ret uncached-minus
[  302.940367]   alloc irq_desc for 265 on node 4
[  302.956874]   alloc kstat_irqs on node 4
[  302.959452] alloc irq_2_iommu on node 0
[  302.974328] igbvf 0000:81:10.4: irq 265 for MSI/MSI-X
[  302.977778]   alloc irq_desc for 266 on node 4
[  302.980347]   alloc kstat_irqs on node 4
[  302.995312] free_memtype request 0xefb28000-0xefb29000
[  302.998816] igbvf 0000:81:10.4: Failed to initialize MSI-X interrupts.

... it turns out that when trying to enable MSI-X,
__assign_irq_vector(new, cfg_new, apic->target_cpus()) can not
get vector because for x2apic target-cpus returns cpumask_of(0)

Update that to online_mask like xapic.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Acked-by: NSuresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <4A785AFF.3050902@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

With CONFIG_STACK_PROTECTOR turned on, VMI doesn't boot with
more than one processor. The problem is with the gs value not
being initialized correctly when registering the secondary
processor for VMI's case.

The patch below initializes the gs value for the AP to
__KERNEL_STACK_CANARY. Without this the secondary processor
keeps on taking a GP on every gs access.
Signed-off-by: NAlok N Kataria <akataria@vmware.com>
Cc: <stable@kernel.org> # for v2.6.30.x
LKML-Reference: <1249425262.18955.40.camel@ank32.eng.vmware.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

The following fix was initially inspired by David Howells fix
few days back:

  http://lkml.org/lkml/2009/7/9/109

However, Ingo disapproves such fixes as it's dangerous (it can
hide future, relevant warnings) - in something as
performance-uncritical.

So, initialize 'err' to '0' to work around a GCC false positive
warning:

  http://lkml.org/lkml/2009/7/18/89

Signed-off-by: Subrata Modak<subrata@linux.vnet.ibm.com>
Cc: Sachin P Sant <sachinp@linux.vnet.ibm.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
LKML-Reference: <20090721023226.31855.67236.sendpatchset@subratamodak.linux.ibm.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

In uv_setup_irq(), the call to create_irq() initially assigns
IRQ vectors to cpu 0. The subsequent call to
assign_irq_vector() in arch_enable_uv_irq() migrates the IRQ to
another cpu and frees the cpu 0 vector - at least it will be
freed as soon as the "IRQ move" completes.

arch_enable_uv_irq() needs to send a cleanup IPI to complete
the IRQ move. Otherwise, assignment of GRU interrupts on large
systems (>200 cpus) will exhaust the cpu 0 interrupt vectors
and initialization of the GRU driver will fail.
Signed-off-by: NJack Steiner <steiner@sgi.com>
LKML-Reference: <20090720142840.GA8885@sgi.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

One system has socket 1 come up as BSP.

kexeced kernel reports BSP as:

[    1.524550] Initializing cgroup subsys cpuacct
[    1.536064] initial_apicid:20
[    1.537135] ht_mask_width:1
[    1.538128] core_select_mask:f
[    1.539126] core_plus_mask_width:5
[    1.558479] CPU: Physical Processor ID: 0
[    1.559501] CPU: Processor Core ID: 0
[    1.560539] CPU: L1 I cache: 32K, L1 D cache: 32K
[    1.579098] CPU: L2 cache: 256K
[    1.580085] CPU: L3 cache: 24576K
[    1.581108] CPU 0/0x20 -> Node 0
[    1.596193] CPU 0 microcode level: 0xffff0008

It doesn't have correct physical processor id and will get an
error:

[   38.840859] CPU0 attaching sched-domain:
[   38.848287]  domain 0: span 0,8,72 level SIBLING
[   38.851151]   groups: 0 8 72
[   38.858137]   domain 1: span 0,8-15,72-79 level MC
[   38.868944]    groups: 0,8,72 9,73 10,74 11,75 12,76 13,77 14,78 15,79
[   38.881383] ERROR: parent span is not a superset of domain->span
[   38.890724]    domain 2: span 0-7,64-71 level CPU
[   38.899237] ERROR: domain->groups does not contain CPU0
[   38.909229]     groups: 8-15,72-79
[   38.912547] ERROR: groups don't span domain->span
[   38.919665]     domain 3: span 0-127 level NODE
[   38.930739]      groups: 0-7,64-71 8-15,72-79 16-23,80-87 24-31,88-95 32-39,96-103 40-47,104-111 48-55,112-119 56-63,120-127

it turns out: we can not use current_cpu_data in phys_pgd_id
for x2apic.

identify_boot_cpu() is called by check_bugs() before
smp_prepare_cpus() and till smp_prepare_cpus() current_cpu_data
for bsp is assigned with boot_cpu_data.

Just make phys_pkg_id for x2apic is aligned to xapic.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Acked-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <4A6ADD0D.10002@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Change SGI UV default apicid mode to "physical". This is
required to match settings in the UV hub chip.
Signed-off-by: NJack Steiner <steiner@sgi.com>
LKML-Reference: <20090727143856.GA8905@sgi.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

The UV BIOS has added additional MMR ranges that are mapped via
EFI virtual mode mappings. These ranges should be deleted from
ranges mapped by uv_system_init().
Signed-off-by: NJack Steiner <steiner@sgi.com>
Cc: linux-mm@kvack.org
LKML-Reference: <20090727143656.GA7698@sgi.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

UV blades may not have any blade-local memory. Add a field
(nid) to the UV blade structure to indicates whether the node
has local memory. This is needed by the GRU driver (pushed
separately).
Signed-off-by: NJack Steiner <steiner@sgi.com>
Cc: linux-mm@kvack.org
LKML-Reference: <20090727143507.GA7006@sgi.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Older versions of binutils did not accept the naked "ASSERT" syntax;
it is considered an expression whose value needs to be assigned to
something.
Reported-tested-and-fixed-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

Booting current 64-bit x86 kernels on the latest Apple MacBook
(MacBook5,2) via EFI gives the following warning:

[    0.182209] ------------[ cut here ]------------
[    0.182222] WARNING: at arch/x86/mm/pageattr.c:581 __cpa_process_fault+0x44/0xa0()
[    0.182227] Hardware name: MacBook5,2
[    0.182231] CPA: called for zero pte. vaddr = ffff8800ffe00000 cpa->vaddr = ffff8800ffe00000
[    0.182236] Modules linked in:
[    0.182242] Pid: 0, comm: swapper Not tainted 2.6.31-rc4 #6
[    0.182246] Call Trace:
[    0.182254]  [<ffffffff8102c754>] ? __cpa_process_fault+0x44/0xa0
[    0.182261]  [<ffffffff81048668>] warn_slowpath_common+0x78/0xd0
[    0.182266]  [<ffffffff81048744>] warn_slowpath_fmt+0x64/0x70
[    0.182272]  [<ffffffff8102c7ec>] ? update_page_count+0x3c/0x50
[    0.182280]  [<ffffffff818d25c5>] ? phys_pmd_init+0x140/0x22e
[    0.182286]  [<ffffffff8102c754>] __cpa_process_fault+0x44/0xa0
[    0.182292]  [<ffffffff8102ce60>] __change_page_attr_set_clr+0x5f0/0xb40
[    0.182301]  [<ffffffff810d1035>] ? vm_unmap_aliases+0x175/0x190
[    0.182307]  [<ffffffff8102d4ae>] change_page_attr_set_clr+0xfe/0x3d0
[    0.182314]  [<ffffffff8102dcca>] _set_memory_uc+0x2a/0x30
[    0.182319]  [<ffffffff8102dd4b>] set_memory_uc+0x7b/0xb0
[    0.182327]  [<ffffffff818afe31>] efi_enter_virtual_mode+0x2ad/0x2c9
[    0.182334]  [<ffffffff818a1c66>] start_kernel+0x2db/0x3f4
[    0.182340]  [<ffffffff818a1289>] x86_64_start_reservations+0x99/0xb9
[    0.182345]  [<ffffffff818a1389>] x86_64_start_kernel+0xe0/0xf2
[    0.182357] ---[ end trace 4eaa2a86a8e2da22 ]---
[    0.182982] init_memory_mapping: 00000000ffffc000-0000000100000000
[    0.182993]  00ffffc000 - 0100000000 page 4k

This happens because the 64-bit version of efi_ioremap calls
init_memory_mapping for all addresses, regardless of whether they are
RAM or MMIO.  The EFI tables on this machine ask for runtime access to
some MMIO regions:

[    0.000000] EFI: mem195: type=11, attr=0x8000000000000000, range=[0x0000000093400000-0x0000000093401000) (0MB)
[    0.000000] EFI: mem196: type=11, attr=0x8000000000000000, range=[0x00000000ffc00000-0x00000000ffc40000) (0MB)
[    0.000000] EFI: mem197: type=11, attr=0x8000000000000000, range=[0x00000000ffc40000-0x00000000ffc80000) (0MB)
[    0.000000] EFI: mem198: type=11, attr=0x8000000000000000, range=[0x00000000ffc80000-0x00000000ffca4000) (0MB)
[    0.000000] EFI: mem199: type=11, attr=0x8000000000000000, range=[0x00000000ffca4000-0x00000000ffcb4000) (0MB)
[    0.000000] EFI: mem200: type=11, attr=0x8000000000000000, range=[0x00000000ffcb4000-0x00000000ffffc000) (3MB)
[    0.000000] EFI: mem201: type=11, attr=0x8000000000000000, range=[0x00000000ffffc000-0x0000000100000000) (0MB)

This arranges to pass the EFI memory type through to efi_ioremap, and
makes efi_ioremap use ioremap rather than init_memory_mapping if the
type is EFI_MEMORY_MAPPED_IO.  With this, the above warning goes away.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
LKML-Reference: <19062.55858.533494.471153@cargo.ozlabs.ibm.com>
Cc: Huang Ying <ying.huang@intel.com>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

The latest Apple MacBook (MacBook5,2) doesn't reboot successfully
under Linux; neither the EFI reboot method nor the default method
using the keyboard controller works (the system just hangs and doesn't
reset).  However, the method using the "PCI reset register" at 0xcf9
does work.

This adds a quirk to detect this machine via DMI and force the
reboot_type to BOOT_CF9.  With this it reboots successfully without
requiring a command-line option.  Note that the EFI code forces
reboot_type to BOOT_EFI when the machine is booted via EFI, but this
overrides that since the core_initcall runs after the EFI
initialization code.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
LKML-Reference: <19062.56420.501516.316181@cargo.ozlabs.ibm.com>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

Startup code for i386 in arch/x86/kernel/head_32.S is using the
reference variable initial_code that is located in the .cpuinit.data
section. If CONFIG_HOTPLUG_CPU is enabled, startup code is not in an
init section and can be called later too. In this case the reference
initial_code must be kept too. This patch fixes this. See below for
the section mismatch warning.

 WARNING: vmlinux.o(.cpuinit.data+0x0): Section mismatch in reference
 from the variable initial_code to the function
 .init.text:i386_start_kernel()
 The variable __cpuinitdata initial_code references
 a function __init i386_start_kernel().
 If i386_start_kernel is only used by initial_code then
 annotate i386_start_kernel with a matching annotation.
Signed-off-by: NRobert Richter <robert.richter@amd.com>
LKML-Reference: <1248716632-26844-1-git-send-email-robert.richter@amd.com>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

Timer interrupts are excluded from being disabled during suspend. The
clock events code manages the disabling of clock events on its own
because the timer interrupt needs to be functional before the resume
code reenables the device interrupts.

The mfgpt timer request its interrupt without setting the IRQF_TIMER
flag so suspend_device_irqs() disables it as well which results in a
fatal resume failure.

Adding IRQF_TIMER to the interupt flags when requesting the mrgpt
timer interrupt solves the problem.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
LKML-Reference: <new-submission>
Cc: Andres Salomon <dilinger@debian.org>
Cc: stable@kernel.org

If we've logically disabled apics, don't probe the PCI space for the
AMD extended APIC ID.

[ Impact: prevent boot crash under Xen. ]
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Reported-by: NBastian Blank <bastian@waldi.eu.org>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>