x86: Fix serialization in pit_expect_msb()

Wei Chong Tan reported a fast-PIT-calibration corner-case:

| pit_expect_msb() is vulnerable to SMI disturbance corner case
| in some platforms which causes /proc/cpuinfo to show wrong
| CPU MHz value when quick_pit_calibrate() jumps to success
| section.

I think that the real issue isn't even an SMI - but the fact
that in the very last iteration of the loop, there's no
serializing instruction _after_ the last 'rdtsc'. So even in
the absense of SMI's, we do have a situation where the cycle
counter was read without proper serialization.

The last check should be done outside the outer loop, since
_inside_ the outer loop, we'll be testing that the PIT has
the right MSB value has the right value in the next iteration.

So only the _last_ iteration is special, because that's the one
that will not check the PIT MSB value any more, and because the
final 'get_cycles()' isn't serialized.

In other words:

 - I'd like to move the PIT MSB check to after the last
   iteration, rather than in every iteration

 - I think we should comment on the fact that it's also a
   serializing instruction and so 'fences in' the TSC read.

Here's a suggested replacement.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
Reported-by: N"Tan, Wei Chong" <wei.chong.tan@intel.com>
Tested-by: N"Tan, Wei Chong" <wei.chong.tan@intel.com>
LKML-Reference: <B28277FD4E0F9247A3D55704C440A140D5D683F3@pgsmsx504.gar.corp.intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

arch/x86/kernel/tsc.c

@@ -275,15 +275,20 @@ static unsigned long pit_calibrate_tsc(u32 latch, unsigned long ms, int loopmin)
  * use the TSC value at the transitions to calculate a pretty
  * good value for the TSC frequencty.
  */
+static inline int pit_verify_msb(unsigned char val)
+{
+	/* Ignore LSB */
+	inb(0x42);
+	return inb(0x42) == val;
+}
+
 static inline int pit_expect_msb(unsigned char val, u64 *tscp, unsigned long *deltap)
 {
 	int count;
 	u64 tsc = 0;
 
 	for (count = 0; count < 50000; count++) {
-		/* Ignore LSB */
-		inb(0x42);
-		if (inb(0x42) != val)
+		if (!pit_verify_msb(val))
 			break;
 		tsc = get_cycles();
 	}
@@ -336,8 +341,7 @@ static unsigned long quick_pit_calibrate(void)
 	 * to do that is to just read back the 16-bit counter
 	 * once from the PIT.
 	 */
-	inb(0x42);
-	inb(0x42);
+	pit_verify_msb(0);
 
 	if (pit_expect_msb(0xff, &tsc, &d1)) {
 		for (i = 1; i <= MAX_QUICK_PIT_ITERATIONS; i++) {
@@ -348,8 +352,19 @@ static unsigned long quick_pit_calibrate(void)
 			 * Iterate until the error is less than 500 ppm
 			 */
 			delta -= tsc;
-			if (d1+d2 < delta >> 11)
-				goto success;
+			if (d1+d2 >= delta >> 11)
+				continue;
+
+			/*
+			 * Check the PIT one more time to verify that
+			 * all TSC reads were stable wrt the PIT.
+			 *
+			 * This also guarantees serialization of the
+			 * last cycle read ('d2') in pit_expect_msb.
+			 */
+			if (!pit_verify_msb(0xfe - i))
+				break;
+			goto success;
 		}
 	}
 	printk("Fast TSC calibration failed\n");