Add the SPI controller driver for Freescale i.MX(S/L/1).
Main features summary:

 > Per chip setup via board specific code and/or protocol driver.
 > Per transfer setup.
 > PIO transfers.
 > DMA transfers.
 > Managing of NULL tx / rx buffer for rd only / wr only transfers.

This patch replace patch-2.6.20-rc4-spi_imx with the following changes:
 > Few cosmetic changes.
 > Function map_dma_buffers now return 0 for success and -1 for failure.
 > Solved a bug inside spi_imx_probe function (wrong error path).
 > Solved a bug inside setup function (bad undo setup for max_speed_hz).
 > For read-only transfers, always write zero bytes.

This is almost the same as the 'BIS' version sent by Andrea, except for
updating the 'DUMMY' byte so that read-only transfers shift out zeroes.
That part of the API changed recently, since some half duplex peripheral
chips require that semantic.
Signed-off-by: NAndrea Paterniani <a.paterniani@swapp-eng.it>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This adds a SPI driver for the Microwire controller on OMAP1 chips.  This
driver has been used in the Linux-OMAP tree for some time now, including
with some of those displays using standardized 9-bit commands followed by
data with 8-bit words.

Microwire only supports half duplex transfers, but that's all that most SPI
protocols need.  When full duplex, or higher speeds, are needed there are
several other controllers that can be used on OMAP.

[akpm@osdl.org: cleanups]
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NImre Deak <imre.deak@solidboot.com>
Signed-off-by: NJuha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Hardware based SPI driver for Samsung S3C24XX SoC systems
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

SPI driver for SPI by GPIO on the Samsung S3C24XX series of SoC processors.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Cc: Greg KH <greg@kroah.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This driver supports the SPI controller on the MPC83xx SoC devices from
Freescale.  Note, this driver supports only the simple shift register SPI
controller and not the descriptor based CPM or QUICCEngine SPI controller.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This driver turns a PXA2xx synchronous serial port (SSP) into a SPI master
controller (see Documentation/spi/spi_summary).  The driver has the following
features:

- Support for any PXA2xx SSP
- SSP PIO and SSP DMA data transfers.
- External and Internal (SSPFRM) chip selects.
- Per slave device (chip) configuration.
- Full suspend, freeze, resume support.
Signed-off-by: NStephen Street <stephen@streetfiresound.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This collects some small SPI patches that seem to be missing from the MM tree:

  - spi_butterfly kbuild hooks got dropped somehow; this restores them
  - quick fix for a (theoretical?) m25p80_write() oops noted by Andrew
  - quick fix for a potential config-specific oops for mtd_dataflash()
  - minor doc tweaks
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds a bitbanging spi master, hooking up to board/adapter-specific glue
code which knows how to set and read the signals (gpios etc).

This code kicks in after the glue code creates a platform_device with the
right platform_data.  That data includes I/O loops, which will usually
come from expanding an inline function (provided in the header).  One goal
is that the I/O loops should be easily optimized down to a few GPIO register
accesses, in common cases, for speed and minimized overhead.

This understands all the currently defined protocol tweaking options in the
SPI framework, and might eventually serve as as reference implementation.

  - different word sizes (1..32 bits)
  - differing clock rates
  - SPI modes differing by CPOL (affecting chip select and I/O loops)
  - SPI modes differing by CPHA (affecting I/O loops)
  - delays (usecs) after transfers
  - temporarily deselecting chips in mid-transfer

A lot of hardware could work with this framework, though common types of
controller can't reach peak performance without switching to a driver
structure that supports pipelining of transfers (e.g.  DMA queues) and maybe
controllers (e.g.  IRQ driven).
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is the core of a small SPI framework, implementing the model of a
queue of messages which complete asynchronously (with thin synchronous
wrappers on top).

  - It's still less than 2KB of ".text" (ARM).  If there's got to be a
    mid-layer for something so simple, that's the right size budget.  :)

  - The guts use board-specific SPI device tables to build the driver
    model tree.  (Hardware probing is rarely an option.)

  - This version of Kconfig includes no drivers.  At this writing there
    are two known master controller drivers (PXA/SSP, OMAP MicroWire)
    and three protocol drivers (CS8415a, ADS7846, DataFlash) with LKML
    mentions of other drivers in development.

  - No userspace API.  There are several implementations to compare.
    Implement them like any other driver, and bind them with sysfs.

The changes from last version posted to LKML (on 11-Nov-2005) are minor,
and include:

  - One bugfix (removes a FIXME), with the visible effect of making device
    names be "spiB.C" where B is the bus number and C is the chipselect.

  - The "caller provides DMA mappings" mechanism now has kerneldoc, for
    DMA drivers that want to be fancy.

  - Hey, the framework init can be subsys_init.  Even though board init
    logic fires earlier, at arch_init ... since the framework init is
    for driver support, and the board init support uses static init.

  - Various additional spec/doc clarifications based on discussions
    with other folk.  It adds a brief "thank you" at the end, for folk
    who've helped nudge this framework into existence.

As I've said before, I think that "protocol tweaking" is the main support
that this driver framework will need to evolve.

From: Mark Underwood <basicmark@yahoo.com>

  Update the SPI framework to remove a potential priority inversion case by
  reverting to kmalloc if the pre-allocated DMA-safe buffer isn't available.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>