EEE support in the 57765 internal phy will not enable after a phy reset
unless it sees that EEE is supported in the MAC.  This patch moves the
code that programs the CPMU EEE registers to a place before the phy
reset.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit 52b02d04 entitled "tg3: Add
EEE support", Ben Hutchings had commented that the EEE advertisement
register will be in a standard location.  This patch moves that
definition into mdio.h and changes the code to use it.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current transmit routines set the jumbo frame BD flag too
aggressively.  This can reduce performance for common cases.  This patch
raises the jumbo flag threshold to 1518, up from 1500.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new PBA format is stored as a string.  This patch allows the
driver to support both the old and new format.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add both NIC and backplane support for FCoE enabled devices IDs.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch will add wake on LAN support to the dev/sub_dev 10FB 11A9.  This
will also include ixgbe ethtool support for this device.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We have had several requests to have ifconfig down command disable
the SFP+ laser and thus make link go down.  Likewise on ifconfig up
the laser would be enabled and link would come up.  This patch enables
that behavior.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently driver set default eswitch configuration values for PF function,
instead of validating values sent by application.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Loopback mode can not be supported in CNA mode. Removing it until FW is fixed.
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For some reason we failed to make this change when perm_addr was
introduced.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We only have direct access to MDIO on Falcon, so move this out of
struct efx_nic.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We only have direct access to SPI on Falcon, so move all this state
out of struct efx_nic.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ethtool EEPROM interface is really meant for exposing chip
configuration, not BootROM configuration.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the Falcon board config is invalid, we cannot proceed - we do not
have a valid board type to pass to falcon_probe_board(), and if we
kluge that to work with an unknown board then other initialisation
code will crash.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mcfw *never* sends CMDDONE when rebooting. Changing this so that it always
sends CMDDONE *before* REBOOT is easy on Siena, but it's not obvious that we
could guarantee to be able to implement this on future hardware.

Given this, I'm less convinced that the protocol should be changed.

To reiterate the failure mode: The driver sees this:

 issue command
 receive REBOOT event

Was that reboot event sent before the command was issued, or in
response to the command? If the former then there will be a subsequent
CMDDONE event, if the latter, then there will be no CMDDONE event.

Options to resolve this are:

 1. REBOOT always completes an outstanding mcdi request, and we set
    the credits count to ignore a subsequent CMDDONE event with
    mismatching seqno.

 2. REBOOT never completes an outstanding mcdi request. If there is
    no CMDDONE event then we rely on the mcdi timeout code to complete
    the outstanding request, incurring a 10s delay.

I'd argue that (2) is tidier, but that incurring a 10s delay is a little
needless. Let's go with (1).
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we enable PMA/PMD loopback this automatically sets RXIN_SEL
(inverse polarity for RXIN).  We need to clear that bit during the
soft-reset sequence, as it is not done automatically.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We do not want to shut down the board based on a fault that has
already been cleared.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set both the 'maximum' and critical temperature limits for LM87
hardware monitors on Falcon boards.  Do not shut down a port until the
critical temperature is reached, but warn as soon as the 'maximum'
temperature is reached.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some errors are expected, e.g. when sending new commands to an MC
running old firmware.  Only the caller of efx_mcdi_rpc() can decide
what is a real error.  Therefore log the error responses with
netif_dbg().
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Delete unnecessary spin_lock for accessing Message Object.
Since all message objects are divided into tx/rx area completely,
spin_lock processing is unnecessary.
Signed-off-by: NTomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Acked-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For easy to readable, LEC #define macros are replaced to enums.
Signed-off-by: NTomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For easy to readable, add Message Object index like below.
PCH_RX_OBJ_START
PCH_RX_OBJ_END
PCH_TX_OBJ_START
PCH_TX_OBJ_END
Signed-off-by: NTomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CAN register of Intel PCH EG20T has 2 sets of interface register.
To reduce whole of code size, separate interface register.
As a result, the number of function also can be reduced.
Signed-off-by: NTomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Acked-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update vxge driver version
Signed-off-by: NJon Mason <jon.mason@exar.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use strncpy instead of memcpy when working on strings
Signed-off-by: NJon Mason <jon.mason@exar.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove printks for ring blocks, fifo blocks, and rx doorbell mode as
they clutter the dmesg output during modprobe and provide no useful
information.
Signed-off-by: NJon Mason <jon.mason@exar.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NIC partitioning is another flavor of multi function - having few
PCI functions share the same physical port. Unlike the currently
supported mode of multi-function which depends on the switch
configuration and uses outer-VLAN, the NPAR mode is switch independent
and uses the MAC addresses to distribute incoming packets to the different
functions. This patch adds the specific HW setting of the NPAR mode
and some distinctions between switch dependent (SD) and
switch independent (SI) multi-function (MF) modes where the configuration
is not the same.

Advance driver version to 1.60.00-6
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the normal debugging functions.
Print mac address when using random_ether_addr.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These were probably just for initial driver debugging
and have not been enabled in builds in git history.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use vsprintf extension %pM for a mac address in one instance.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Neaten the phy_init function by adding and calling vendor
specific functions.

object size is reduced by ~1kb:

$ size drivers/net/forcedeth.o.*
   text	   data	    bss	    dec	    hex	filename
  83475	   1848	  19304	 104627	  198b3	drivers/net/forcedeth.o.new
  84459	   1848	  19544	 105851	  19d7b	drivers/net/forcedeth.o.old
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>